Operating Manual
Table Of Contents
- OPERATING MANUAL
- NUMERICAL INDEX
- SAFETY INSTRUCTIONS
- OPERATION
- 1. Driver seat
- 2. Display instruments and operating controls
- 3. Heating and ventilation
- 4. Rearwiew mirror
- 5. Start-up
- 6. Starting and stopping the engine
- 7. Vario transmission
- 8. Fuel consumption measurement
- 9. Tractor Management System (TMS)
- 10. PTO
- 11. Four wheel drive (4-WD)
- 12. Differential lock
- 13. Front axle suspension
- 14. Power lift and PTO automatic mode
- 15. Brakes
- 16. Steering
- 17. Hydraulics
- 18. Electronic lifting gear control, rear
- 19. Three-point link
- 20. Front power lift
- 21. Trailing devices
- 22. Compressed air system
- 23. Additional ballasting
- 24. Track adjustment
- 25. Twin tyres
- 26. On-board computer
- 27. Computer
- 28. Storing the settings
- 29. Implement control
- 30. Variotronic Ti
- CARE AND MAINTENANCE
- 1. General
- 2. Opening the bonnet
- 3. Engine oil change
- 4. Fuel system
- 5. Dry air .lter
- 6. Cooling system
- 7. V belt
- 8. Brake and clutch system
- 9. Front PTO
- 10. Transmission and axle drives
- 11. Four-wheel drive axle
- 12. Power lift
- 13. Hydraulic system
- 14. Steering
- 15. Front wheels
- 16. Heating and ventilation
- 17. Air conditioning
- 18. Windshield washer system
- 19. Cleaning the tractor
- 20. Electrical and electronic systems
- 21. Fuses
- 22. Wiring diagrams
- IMPLEMENTS
- FAULTS AND REMEDIAL ACTIONS
- TECHNICAL DATA
- ALPHABETICAL INDEX
- Important information on service and maintenance
117
OPERATION
Text-module
NOTE:
Press ESC to return to previous menu level.
28. Storing the settings
Text-module
This setting saving function allows four different
sets of parameters to be saved and named un-
der any name and recalled when needed.
28.1 Setting that can be saved
Text-module
Comfort front power lift
● Lock status
● Cross adjustment - floating setting
● Lift flow regulation
● Lower flow regulation
● Maximum lifting height
Text-module
Rear power lift (EPC)
● Lock status
● Slip control status
● Lowering speed
● Mix ratio (position/traction control)
● Wheel slip setting
● Switch-on speed for vibration damping
● Maximum lifting height
● Automatic function
Text-module
Rear PTO
● Rear PTO rpm
● Automatic function
Text-module
Electrical valves 1-4
● Valve priority
● Lock status
● Kick-out status
Activate PTO measurement (can also be
combined with lifting gear measurement
and/or external counter).
To activate, press key (F4) - the
green symbol indicates active
status.
Measuring and counting only
available with rear or front PTO
engaged.
Activating external counter input.
Connect cable (ID. No. 0071 023
100) to blue socket (see picture
OPERATION Fig. 270).
To activate, press key (F5). When
activated, the symbol is lit green.
Measuring and counting only
possible if there is a sealed
counting sensor on the implement
(e.g. hydraulic fertiliser spreader)
and this is connected to the
on-board computer.
● Timer setting
● Lift flow regulation
● Lower flow regulation
● Timer function selection
Text-module
External valve actuation
● Valve selection (3rd valve or 4th valve)
Text-module
Load limit control
● Engine speed drop set value
Text-module
Cruise control
● Tempomat cruise control speed 1
● Tempomat cruise control speed
pre-selection 1
● Speed cruise control 2
● Tempomat cruise control speed
pre-selection 2
Text-module
Quick reverse
● Reversing speed
Text-module
Electronic accelerator
● Min/Max engine speed values
Text-module
4WD
● 4-WD pre-selection
Text-module
Differential lock
● Pre-select differential lock
Text-module
Suspension
● Suspension mode pre-selection
Text-module
Tractor Management System (TMS)
● TMS operation ON
● Accelerator mode ON
● Set engine speed range
● Operating status (PTO, power lift, hydraulic
valve function) of the engine speed control
Text-module
Variotronic Ti
● Stored operating sequences available for
play back