Installation Guide

ManualsBrandsFELYL ManualsBathCaffee 48 in. W x 58 in. H GYM Use Pivot Frameless Tub Door in Bright Gray Finish with Water Repellent Clear Glass

Table Of Contents

Summary of content (12 pages)

PAGE 1
FELL no2 S N wore a OOr Shower Door Instruction Guide Left Hand Install Right Hand Install
PAGE 2
PAGE 3
PART LIST Check all parts according to the list before assembly . Feel free to contact with us if you need assistance .
PAGE 4
Left Hand Assembly STEP 1 1.Put wall-mounted stabilizer strip for fixed panel(3) on bathtub,the distance is 5mm to bathtub. 2. Hold wall-mounted stabilizer strip for fixed panel(3) against the wall, level it vertical and mark the hole positions with pencil. 3. Take off wall-mounted stabilizer strip(3) and drill holes on markings. 4. Hammer the plug into hole. 5. Secure wall-mounted stabilizer strip(3) with 4*30 screws(2). Right Hand Assembly STEP 1 1.
PAGE 5
Left Hand Assembly STEP 2 1. Lay glass clamp(7) on the tile, place the fixed panel(5) base part into glass clamp(7), fit fixed panel(5) into wall-mounted stabilizer strip(3), level it vertical with level and mark the clamp(7) position with distance is 460mm from wall to glass clamp) 2. Take off fixed panel(5), then place glass clamp(7) on the marking and mark the hole position with pencil. 3. Take off clamp(7) and drill holes on the markings. 4. Hammer the plug into the hole. 5.
PAGE 6
Left Hand Assembly STEP 3 1. Loose the rail-side screw of top rail connected glass clamp(16) with Allen wrench, fit top rail(17) into hole and secure with screw, and then assemble wall-mounted top rail connector(19) to the other end of the top rail(21). 2. Loose top screw and fit its slot into fixed panel(5), adjust the position of wall-mounted top rail connector(19), then mark hole position of the connector(19). 3. Take off wall-mounted top rail connector(19) and drill holes on the markings. 4.
PAGE 7
Left Hand Assembly STEP 4 1. Assemble the left-side wall-mounted strip connector(9) and the right-side strip connector(12) to Aluminum strip(10). 2. Fit the slot into fixed panel(5) Right Hand Assembly STEP 4 1. Assemble the right-side wall-mounted strip connector(9) and the left-side strip connector(12) to Aluminum strip(10). 2. Fit the slot into fixed panel(5).
PAGE 8
Left Hand Assembly STEP 5 1. Assemble shower door hinges(6) on the movable shower door(13). Inside View Right Hand Assembly STEP 5 1. Assemble shower door hinges(6) on the movable shower door(13).
PAGE 9
PAGE 10
STEP 7 1. Assemble tubular single-sided towel bar(14) onto Left Hand Assembly movable shower door(13). STEP 7 Right Hand Assembly 1. Assemble tubular single-sided towel bar(14) onto movable shower door(13).
PAGE 11
Left Hand Assembly Right Hand Assembly STEP 8 STEP 8 1. Install Side seal strip(15) .Open the Movable shower 1. Install Side seal strip(15) .Open the Movable shower insert Side seal strip(15) to side of Movable insert Side seal strip(15) to side of Movable shower door(13) . shower door(13) . 2. Install Shower door bottom seal strip(11). Insert Shower 2. Install Shower door bottom seal strip(11).
PAGE 12
Left Hand Assembly STEP 8 1. Apply qualified mildew resistant silicone along the sides of wall-mounted stabilizer strip for fixed panel(3), Aluminum strip(10) and fixed panel(5) base. Allow the silicone to dry for 24 hours before using the shower. Right Hand Assembly STEP 8 1. Apply qualified mildew resistant silicone along the sides of wall-mounted stabilizer strip for fixed panel(3), Aluminum strip(10) and fixed panel(5) base. Allow the silicone to dry for 24 hours before using the shower.