FeiYu Tech FeiYu Y6 scorpion Copter Frame Instruction Manual Please read the manual carefully before using FeiYu Y6 Guilin Feiyu Electronic Technology Co., Ltd 4th Floor,Yu Tai Jie Science&technology Building, Information Industry Park, ChaoYang Road ,Qi Xing District , Guilin 541004, China http://www.feiyudz.cn Email: service@feiyu-tech.
GuiLin FeiYu Electronic Technology Co., Ltd Features 1. Dimensions 450mm 681mm 2. Empty Frame Weight: 630g (receiver and battery not included) 3. Payload Capability: 900g ( battery, receiver, and camera included) 4. Maximum Gross Take-Off Weight: 1430g. DO NOT OVERLOAD ON FeiYu Y6 WHICH CAN LEAD TO DANGER. 5. Airborne period: >10mins (with 3S 2200mAh battery) 6. Cell Chemistry: 3S 1500mAh ~ 5000mAh Lithium Polymer, and instant discharge capacity >15C. Support PWM normal ESC. 7. Can install FY91Q.
GuiLin FeiYu Electronic Technology Co., Ltd Install Tools needed to build the Y6: Soldering Iron Rosen Core Solder Allen Wrench (provided) Step 1:Frame Arm Assembly prop eller Brushless motro M3*5mm Scoket Screw M3×30mm Pillar Right Arm M3×5mm Scoket Screw soldering point Left Arm soldering point Leg Note: There are three LED on the side of arm,The LED should on out side. Unpack the Frames, separate them as to color of l.e.d.’s i.e. Blue, Red, Green. Remove the m3x5mm button head screws.
GuiLin FeiYu Electronic Technology Co., Ltd pillars to the holes in the side frame. Make sure that the led’s are facing to the outside. Take the opposite side frame making sure the led’s are facing outwards and the Weld points are on the same end. Do not tighten the screws yet, Now take the motor with it’s mount and position it in the bottom slots that are cut in the side frames, snug down the button head screws for the motor. Now take the landing gear and position it so the long end is pointing down.
GuiLin FeiYu Electronic Technology Co., Ltd M3×25mm Pillar Fuselage with Electronic components Cross any two wire , change Motor rotation Magic cable tie through square groove welding ESC Step 3: Welding (soldering) the frames to the bottom fuse plate with the electronics. To accomplish this you will need a small soldering iron aprox. 35w. Plug in the soldering iron and while it is coming to temperature, gather your Rosen Core solder and safety glasses. With the soldering iron at temp.
GuiLin FeiYu Electronic Technology Co., Ltd volt meter and on DC range, check for proper voltage Aprox. 2.3vdc is present at the weld points. Once you have the led’s inspected, remove the battery, place the fuselage you removed previously and place eight button head screws in the corresponding holes and tighten them. The Magic cable tie use for fixed battery. The frame Power detection support 3S (11.1V )battery. Connect a 3S Lipo Balance plug to the plug on the bottom of the Fuselage.
GuiLin FeiYu Electronic Technology Co., Ltd Propeller installation Pay attention to the installation of the propeller direction. Front 3 2 5 6 Y6 SCORPION FLYER 1 4 1 (top) = ESC 1 CW 2 (top) = ESC 2 CW 3 (top) = ESC 3 CW 4 (bottom) = ESC 4 CCW 5 (bottom) = ESC 5 CCW 6 (bottom) = ESC 6 CCW cw = clock wise ccw = counter clockwise ——END—— Note: We reserve the right to change this manual at any time! And the newest edition will be shown on our website www.feiyudz.cn.
