Installation Instructions

ManualsBrandsFeit Electric ManualsIndoor Lighting5"and 6" Deep Baffle LED Recessed Retrofit Downlight

REV003

IMPORTANT SAFETY

INSTRUCTIONS AND

INSTALLATION GUIDE

READ BEFORE INSTALLATION

SAVE THESE INSTRUCTIONS

Questions, problems, missing parts?

Before returning to the store, call Feit Electric Customer Service

8 a.m. - 5 p.m., PST, Monday-Friday 1-866-326-BULB (2852)

ITEM # LEDR56DB/6WYCA

Please read and understand this entire manual before attempting to assemble, operate or install this

product. This product must be installed in accordance with any applicable installation code(s) by a qualified

electrician or person familiar with the construction and operation of the product and the hazards involved.

• RISK OF FIRE OR ELECTRIC SHOCK: The electrical rating

of this product is 120VAC.

• RISK OF FIRE OR ELECTRIC SHOCK: Install this product

only in luminaires that have the construction features and

dimensions shown in the photographs and/or drawings in this

manual.

• To prevent wiring damage or abrasion, do not expose wiring to

edges of sheet metal or other sharp objects.

• RISK OF SHOCK – DISCONNECT POWER BEFORE

INSTALLATION

• Do not make or alter any open holes in an enclosure of wiring

or electrical components during installation.

• THIS DEVICE IS NOT INTENDED FOR USE WITH

EMERGENCY EXITS.

• RISK OF FIRE OR ELECTRIC SHOCK: LED Recessed

Downlight with Trim installation requires knowledge of

luminaires electrical systems. If not qualified, do not attempt

installation. Contact a qualified electrician.

To avoid possible electrical shock, be sure

that the power is turned off at the fuse box

or circuit breaker before installing or

servicing the product. For your safety, read

and understand the instructions completely

before beginning installation.

WARNING

CAUTION

WARRANTY

Supplier’s Declaration of Conformity:

47 CFR § 2.1077 Compliance Information

Responsible Party:

Feit Electric Company

4901 Gregg Road,

Pico Rivera, CA 90660, USA

562-463-2852

Unique Identifier:

FEIT ITEM # LEDR56DB/6WYCA

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found

to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the

separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult

the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the manufacturer could void the user's

authority to operate the equipment.

This product is warrantied to be free from defects in workmanship and materials for up to five years from date of purchase. If the product fails within the warranty

period, please contact Feit Electric at info@feit.com, visit feit.com/contact-us or call 1-866-326-BULB (2852) for instructions on replacement or refund.

REPLACEMENT OR REFUND IS YOUR SOLE REMEDY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES ARE

LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY

EXPRESSLY EXCLUDED. Some states and provinces do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion

may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.

FEIT ELECTRIC COMPANY | PICO RIVERA, CA | 1-866-326-BULB (2852) | FAX (562) 908-6360 | www.feit.com

Summary of content (4 pages)

PAGE 1
ITEM # LEDR56DB/6WYCA Questions, problems, missing parts? Before returning to the store, call Feit Electric Customer Service 8 a.m. - 5 p.m., PST, Monday-Friday 1-866-326-BULB (2852) IMPORTANT SAFETY INSTRUCTIONS AND INSTALLATION GUIDE READ BEFORE INSTALLATION SAVE THESE INSTRUCTIONS Please read and understand this entire manual before attempting to assemble, operate or install this product.
PAGE 2
PACKAGE CONTENTS Before beginning installation of this product, make sure all parts are present. Compare parts with package contents list and diagram. If any part is missing or damaged, do not attempt to assemble, install or operate this product. COMPONENTS INCLUDED A B C A (1) MEDIUM BASE ADAPTER (1) RECESSED DOWNLIGHT (1) INSTRUCTION MANUAL B PRODUCT ELECTRICAL RATINGS 120 V / 60 Hz, XX mA, 10.5 W WET LOCATION LISTED, ACCEPTABLE IN SHOWER INSTALLATIONS.
PAGE 3
HOW TO SELECT YOUR LIGHT COLOR Soft White 2700K Bright White 3000K Neutral White 3500K Cool White 4000K Daylight 5000K Light Switch (SWITCH) NOTICE: PICK YOUR FAVORITE LIGHT COLOR BEFORE INSTALLING • You can lock in one color temperature or change among multiple color temperatures, it will memorize the last color temperature and reset automatically. • When the slide switch is set to SW (Soft White), the color temperature is set at 2700K.
PAGE 4
INSTALLATION INTO EXISTING RECESSED FIXTURE NOTE: For use with 5 in. and 6 in. recessed housings (housing sold separately) 1 Turn off the power at the switch and fuse box or circuit breaker. 2 Remove the existing trim installed in the recessed housing (if necessary). 3 If applicable, slide the lampholder bracket to its upward maximum position.