Installation Manual

ManualsBrandsFeig Electronic ManualsElectronicsSecurity Gate

INSTALLATION

draft

public (B)

2008-02-05

M71104-1e-ID-B.doc

OBI

i-scan

ID ISC.ANT1300/680

Typ A

English

Summary of content (50 pages)

PAGE 1
OBID i-scan ® INSTALLATION ID ISC.ANT1300/680 Typ A English draft public (B) 2008-02-05 M71104-1e-ID-B.
PAGE 2
OBID i-scan® Installation ID ISC.ANT1300/680-A Note © Copyright 2008 by FEIG ELECTRONIC GmbH Lange Strasse 4 D-35781 Weilburg-Waldhausen Tel.: +49 6471 3109-0 http://www.feig.de With the edition of this document, all previous editions become void. Indications made in this manual may be changed without previous notice. Copying of this document, and giving it to others and the use or communication of the contents thereof are forbidden without express authority.
PAGE 3
OBID i-scan® Installation ID ISC.ANT1300/680-A Contents 1 Safety Instructions / Warning - Read before Start-Up ! 6 2 Performance Features of the ID ISC.ANT1300/680 Antennas 7 2.1 3 Available Antenna Types ..............................................................................................7 Installation and Wiring 8 3.1 Dimensions of antenna .................................................................................................8 3.2 Mounting preparation...................
PAGE 4
OBID i-scan® Installation ID ISC.ANT1300/680-A 4.3.7 Setting the Antenna Tuner ............................................................................................30 4.3.8 Reader Configuration with Multiplexer...........................................................................32 4.3.9 Tuning the Gate Antenna with Multiplexer.....................................................................34 4.4 Testing the Gate Antenna ..................................................................
PAGE 5
OBID i-scan® 1 Installation ID ISC.ANT1300/680-A Safety Instructions / Warning - Read before Start-Up ! • The device may only be used for the intended purpose designed by for the manufacturer. • The operation manual should be conveniently kept available at all times for each user. • Unauthorized changes and the use of spare parts and additional devices which have not been sold or recommended by the manufacturer may cause fire, electric shocks or injuries.
PAGE 6
OBID i-scan® 2 Installation ID ISC.ANT1300/680-A Performance Features of the ID ISC.ANT1300/680 Antennas The ID ISC.ANT1300/680 Type A antenna is the version with dynamicTuning Board ID ISC.DAT mounted.
PAGE 7
OBID i-scan® 3 3.1 Installation ID ISC.ANT1300/680-A Installation and Wiring Dimensions of antenna The outside dimensions of the antenna are shown in Fig. 1 Fig. 1: Antenna outside dimensions All dimensions are in mm with general tolerance to ISO 2768 m (mean). FEIG ELECTRONIC GmbH Page 8 of 50 M71104-1e-ID-B.
PAGE 8
OBID i-scan® 3.2 Installation ID ISC.ANT1300/680-A Mounting preparation For assembly the antenna must be carefully unpacked. This is done as described in the following steps: 1. Place the packed antenna on the floor with the top side facing up. Carefully open the box and then remove the antenna. Fig. 2: Antenna in its packaging 2. After that the antenna has to be placed carefully again on the floor.
PAGE 9
OBID i-scan® 3.3 Installation ID ISC.ANT1300/680-A Installing the antenna Notes: Before installing the antennas please read 4.1 Project Notes . The spacing of the antennas comprising a gate depends on the antenna configuration. If multiple antennas or gates are connected to different Readers, a minimum separation of 8 m must be kept between the antennas or gates. For shorter distances (1 m – 8 m) the Readers must be multiplexed. Below a distance of 1.
PAGE 10
OBID i-scan® Installation ID ISC.ANT1300/680-A The size and type of the screw anchors depends considerably on the strength of the base or floor. The anchors should be capable of withstanding a permissible load of at least 5 kN per anchor for all load directions (e.g. for concrete floor Hilti HVA anchors with HAS-(E) M8 threaded rod or Hilti HIS-N M8 (5/16”) threaded inserts). The size of the mounting holes in the antenna is 10 mm (.39”).
PAGE 11
OBID i-scan® Installation ID ISC.ANT1300/680-A 3.3.2 Installing the Antenna Base and Antenna Body The antenna will be screwed on the floor. Use the adjusting screws (Fig. 6) to align the antenna vertically. Adjusting screws (hexagon socket width A/F5) Fig. 6: Attaching and aligning the antenna FEIG ELECTRONIC GmbH Page 12 of 50 M71104-1e-ID-B.
PAGE 12
OBID i-scan® 4 Installation ID ISC.ANT1300/680-A Typical Antenna Configuration (Gate Antenna with two Antennas) The standard configuration of a gate with three-dimensional tag orientation consists of two ID ISC.ANT1300/680 Type A with reader and power splitter or multiplexer. If a tag moves through the gate horizontally, it can be read at lease once. This ensures high reliability of the antenna system. 4.
PAGE 13
OBID i-scan® Installation ID ISC.ANT1300/680-A If multiple gates are arranged with short distances between each other, these will mutually interfere with each other. The Readers for the respective gates must then be synchronized. To achieve three-dimensional capture of the tag in the capture area drawn above, the following conditions must be met: - The gate distance GD depends on the antenna configuration (see Table 2: Design notes). - The tags should be at least ISO card size (46 mm x 75 mm).
PAGE 14
OBID i-scan® 4.2 Installation ID ISC.ANT1300/680-A Configuration and Setup using Antenna Type -A with power splitter 4.2.1 Required Components To construct the gate you need the following components: - Qty. 2 Antenna ID ISC.ANT1300/6800 Type A - Qty. 1 Reader module ID ISC.LR2000-A-M - Qty. 1 Power splitter module ID ISC.ANT-PS-BM - Qty. 1 Gate integration kit ID ISC.ANT.GIK - Qty. 1 power supply ID ISC.
PAGE 15
OBID i-scan® Installation ID ISC.ANT1300/680-A 4.2.2 Contents of the Gate- Integration- Kit ID ISC.ANT.GIK The following parts are contents of the Gate- Integration- Kit . 3. 4. 1. 2. 5. 8. 11. 13. 6. 9. 7. 12. 10. Position Qty. Name / Use 1. 1 DC- cable relay / Connection Buzzer – Relay Output – 24V 2. 2 DC-cable Reader, PS, Mux / DC-Connection to Terminal block – Reader, PS or Mux 3. 1 3,65m coaxial cable/ HF- Connection Reader – Mux (just at the use of Mux) 4.
PAGE 16
OBID i-scan® Installation ID ISC.ANT1300/680-A 4.2.3 Mounting of the components at the use of the Power Splitter Step Action 1 Mounting of the reader with the screw M4x8 Pos.13 2 Mounting of the Power Splitter with the hexagon spacer bolts M3x6 Pos.11 and the screws M3x6 Pos.12 3 4 Note 11. 12. Mounting of the Terminal block Pos.8 with the screws M3x10 Pos.10 and connection of the terminals 1+2 (+24V) and 3+4 (GND) with the bridges. Pos.9 Mounting of the relay cable Pos.
PAGE 17
OBID i-scan® 5 Installation ID ISC.ANT1300/680-A Mounting of the DCcables Pos.2 of the readers and of the PS with 2 pieces of cable tie 2,5x105mm Pos.6 Attention! Take care of polarity. 6 Connect DC- cables to Terminal block . Attention! Take care of polarity. Red wire to terminal 1+2 (+24V), Black wire to terminal 3+4 (GND) 7 8 9 Connect the antenna cable with X3 of PS. Wind up the rest of the cable to loops and tied it together with 2 pieces of cable tie 4,8x280mm Pos.
PAGE 18
OBID i-scan® Installation ID ISC.ANT1300/680-A 4.2.4 Configuration of a Gate antenna with power splitter Connect the components as shown in Fig. 8 2 Tuning boards of antennas ID ISC.ANT1300/680 Long Range Reader ID ISC.LRM2000 X9, Pin1+3 Torrid core Pos.4 1,35m 3,60m X4 X3 X1 Pos.8 Pos.2 Pos.1 X1 X2 IN1 Power Splitter ID ISC.ANT.PS-BM DC Power supply 24V Fig.
PAGE 19
OBID i-scan® Installation ID ISC.ANT1300/680-A 4.2.5 Setting the Power Splitter Set the jumpers on the Power Splitter as shown Table 3:Power Splitter setting. More information about setting the ID ISC.ANT.PS-BM Power Splitter can be found in the corresponding installation manual (M40402-xde-ID-B).
PAGE 20
OBID i-scan® Installation ID ISC.ANT1300/680-A Now you must remove the to fastening screws (hexagon socket width A/F2,5) of the antenna tuner cover and remove it upwards. Fig. 11 Step 3 Step 4 Fig. 11 Removing the antenna tuner cover The ID ISC.
PAGE 21
OBID i-scan® Installation ID ISC.ANT1300/680-A 4.2.7 Reader Configuration with Power Splitter To tune the antennas, open the ISOStart software and first read out the current configuration of the Reader: Step Action Note Start ISOStart Software 1 2 Run „Detect“... 3 ...follow „New-File Assistant“... 4 ...
PAGE 22
OBID i-scan® Step Installation Action ID ISC.ANT1300/680-A Note CFG1: Interface and Mode 6 7 To tune, activate “ISO-Host Mode” Set by clicking on “Write” FEIG ELECTRONIC GmbH Page 23 of 50 M71104-1e-ID-B.
PAGE 23
OBID i-scan® Installation ID ISC.ANT1300/680-A 4.2.8 Tuning the Gate Antenna with Power Splitter Before tuning the Gate Antenna you must quit the ISOStart software. Then the gate may be tuned according to the following sequence: Step 1 Action Note Start “DATuningTool” Software Click on “Detect Reader...
PAGE 24
OBID i-scan® 4.3 Installation ID ISC.ANT1300/680-A Configuration and Setup using Antennas Type –A with Multiplexer 4.3.1 Required Components To construct the gate you need the following components: - Qty. 2 Antenna ID ISC.ANT1300/680 Type A - Qty. 1 Reader module ID ISC.LR2000-A-M - Qty. 1 Multiplexer module ID ISC.ANT.MUX-A-M - Qty. 1 Gate integration kit ID ISC.ANT.GIK - Qty. 1 power supply ID ISC.
PAGE 25
OBID i-scan® Installation ID ISC.ANT1300/680-A 4.3.2 Mounting of the components at the use of the Multiplexer Step Action 1 Mounting of the reader with the screw M4x8 Pos.13 2 Mounting of the Multiplexer with the hexagon spacer bolts M3x6 Pos.11 and the screws M3x6 Pos.12 3 4 Note 12. 11. Mounting of the Terminal block Pos.8 with the screws M3x10 Pos.10 and connection of the terminals 1+2 (+24V) and 3+4 (GND) with the bridges. Pos.9 Mounting of the relay cable Pos.
PAGE 26
OBID i-scan® 5 Installation ID ISC.ANT1300/680-A Mounting of the DCcables Pos.2 of the readers and of the Multiplexer with 2 pieces of cable tie 2,5x105mm Pos.6 Attention! Take care of polarity. 6 Connect DC- cables to Terminal block . Attention! Take care of polarity. Red wire to terminal 1+2 (+24V), Black wire to terminal 3+4 (GND) 7 8 9 Connect the antenna cable with Out 1 of Multiplexer. Wind up the rest of the cable to loops and tied it together with 2 pieces of cable tie 4,8x280mm Pos.
PAGE 27
OBID i-scan® Installation ID ISC.ANT1300/680-A 4.3.3 Configuration of a Gate antenna with Multiplexer Connect the components as shown in Fig. 12. 2 Tuning boards of antennas ID ISC.ANT1300/680 Long Range Reader ID ISC.LRM2000 X9, Pin1+3 3,60m Torrid core Pos.4 Pos.3 1,35m 3,60m X3 X1 Pos.8 X1 Pos.7 Pos.2 Pos.1 X2 IN1 OUT1 Multiplexer OUT2 ID ISC.ANT.MUX-A-M DC Power supply 24V Fig.
PAGE 28
OBID i-scan® Installation ID ISC.ANT1300/680-A 4.3.4 Setting the Multiplexer Set the jumpers JP1-JP8, JP11-JP18 and DIP switch S1 on the Multiplexer as shown. More on setting the ID ISC.ANT.MUX Multiplexer can be found in the corresponding installation manual (M30201-xde-ID-B). Fig. 14: DIP-Switch and Jumper positions 4.3.
PAGE 29
OBID i-scan® Installation ID ISC.ANT1300/680-A 4.3.6 Jumper Configuration Jumpers JP1 to JP8 must be set according to the following table. Table 6: Configuration JP1-8 Jumper Position In addition, close jumpers JP11 to JP18. 4.3.7 Setting the Antenna Tuner To check the settings of the antenna tuner the antenna foot has to be opened. For that you must remove the to fastening screws (hexagon socket width A/F2,5) of the antenna foot cover and remove it upwards. Fig. 10 Step 1 Step 2 Fig.
PAGE 30
OBID i-scan® Installation ID ISC.ANT1300/680-A Now you must remove the to fastening screws (hexagon socket width A/F2,5) of the antenna tuner cover and remove it upwards. Fig. 11 Step 3 Step 4 Fig. 16 Removing the antenna tuner cover ID ISC.
PAGE 31
OBID i-scan® Installation ID ISC.ANT1300/680-A 4.3.8 Reader Configuration with Multiplexer To tune the antennas, open the ISOStart software and first read out the current configuration of the Reader: Step Action Note Start ISOStart Software 1 2 Run „Detect“... 3 ...follow „New-File Assistant“... 4 ...
PAGE 32
OBID i-scan® Step Installation Action ID ISC.ANT1300/680-A Note CFG1: Interface and Mode 6 To tune, activate “ISO-Host Mode” 7 Set by clicking on “Write” 8 CFG15: Antenna Multiplexing Ι Activate „Multiplexing“ Configure the parameters as follows: • „Switching Condition“ – after no response • „Number of Input Channels“ – 1 Input (Single Mode) • „MUX-Valid Time“ – 100 x 5 ms • „Number of Output Channels“ => 2 9 Set by clicking on “Write” FEIG ELECTRONIC GmbH Page 33 of 50 M71104-1e-ID-B.
PAGE 33
OBID i-scan® Installation ID ISC.ANT1300/680-A 4.3.9 Tuning the Gate Antenna with Multiplexer Before tuning the gate antenna, you must quit the ISOStart software. Then the gate can be tuned as follows: Step 1 Action Note Start “DATuningTool” software Select “Detect Reader...”. 2 In the „Detect Reader“ window select the interface (COM-Port 1, BusAdr. 0) and then select “Detect”.
PAGE 34
OBID i-scan® 4.4 Installation ID ISC.ANT1300/680-A Testing the Gate Antenna After tuning the gate antenna, you can check for proper function using the Reader, the ISOStart service software and a Smart Tag. Here the Noise Level and performance of the gate are tested. 4.4.
PAGE 35
OBID i-scan® Installation ID ISC.ANT1300/680-A 4.4.2 Reading a Serial Number Step Action Note 1 Attach a tag to an antenna Use adhesive tape, for example 2 Select „Test and Measurement“ Select „ISO Inventory“ function and activate by clicking on „Start“. 3 The serial number and tag type will be shown in the display. 4.4.3 Testing the performance In this test the capture area of the gate antenna described in 4.1 Project Notes is checked.
PAGE 36
OBID i-scan® Installation ID ISC.ANT1300/680-A The test begins by checking the read range outside the gate (see Fig. points c and d), assuming the configuration and locality permit it. Start the ISO Inventory command in the ISOStart program as described in 4.4.2 Reading a Serial Number. If the tag is oriented parallel to the antenna towards the outside, a read range of 65 to 75 cm should be achieved. The three tag orientations are checked inside the gate.
PAGE 37
OBID i-scan® 4.5 Installation ID ISC.ANT1300/680-A Connecting and Setting the Alarm Kit (optional) The solution provided here presumes that all alarm indicators (buzzer) are wired in parallel and switched through the relay X11 on the ID ISC.LR2000-A-M Reader. The pulse duration can be set (CFG2 / REL1) between 100 ms and 6553.5 s by adjusting the Reader configuration. Relay X11 provides a changeover contact for low voltages. 4.5.
PAGE 38
OBID i-scan® Installation ID ISC.ANT1300/680-A 4.5.3 Reader Setting for Indicators The ISOStart software can be used to set the Reader so that relay X11 opens or closes when a Transponder is read. Step Action 1 Start ISOStart Software 2 Select “Configuration” and click on “Read” to read the .
PAGE 39
OBID i-scan® Installation ID ISC.ANT1300/680-A ISO 15693 Mode Enter desired value in „AFI“ field. 7 8 Set by clicking on “Write” FEIG ELECTRONIC GmbH Page 40 of 50 M71104-1e-ID-B.
PAGE 40
OBID i-scan® Installation ID ISC.ANT1300/680-A 4.5.4 Programming a Transponder with the AFI Byte If the transponders will remain on the object when leaving the storage location, they must first be cancelled. This is generally done by writing to a particular area of the transponder. The AFI byte (Application Family Identifier) is useful for this purpose, since it is contained in nearly all transponder models in the 13.56 MHz family.
PAGE 41
OBID i-scan® 7 Installation ID ISC.ANT1300/680-A To verify, read AFI byte by selecting [0x2B] Get System Information FEIG ELECTRONIC GmbH Page 42 of 50 M71104-1e-ID-B.
PAGE 42
OBID i-scan® 4.6 Installation ID ISC.ANT1300/680-A Activating Buffered Read Mode „Buffered Read Mode“ is the normal operating mode of the Reader. Here the tags are read at maximum speed and the information is stored in the Reader’s ring buffer. This data sets can be read by the host. To activate „Buffered Read Mode“ proceed as follows: Step Action Note Select „Configuration“ 1 CFG11: Read Mode –Read Data 2 TR.
PAGE 43
OBID i-scan® 4.7 Installation ID ISC.ANT1300/680-A Configuring the Reader in accordance with national RF regulations Configuration of the RFID Readers and the maximum transmitting power of the antennas are affected mainly by the country-specific RF regulations. For the entire EU the limits are set forth in the R&TTE Directive and EN 300 330. In North America this is regulated by FCC Part 15 (USA) and by the RSS-210 (Canada). The ID ISC.ANT1300/680 antenna with the ID ISC.
PAGE 44
OBID i-scan® Installation ID ISC.
PAGE 45
OBID i-scan® 5 Installation ID ISC.ANT1300/680-A Technical Data 5.1 Antenna ID ISC.ANT1300/680- Type A Mechanical Data • Housing UV stabilized ABS • Dimensions ( W x H x D ) 720 x 1680 x 86 mm ± 5 mm • Weight – ID ISC.ANT1300/680-A Approx. 15 kg with/ 20 kg without packing • Enclosure rating IP 54 • Color Antenna frame: light grey RAL 7035 Antenna foot: signal black RAL 9004 • Mounting – No.
PAGE 46
OBID i-scan® Installation • Permissible overall transmitting power per antenna gate – EU-territory (per EN 300 330) and other CEPT nations – USA (per. FCC Part 15) ID ISC.ANT1300/680-A 8.0 W 8.0 W • Outputs – 1 Optocoupler – 1 Differential Output – 1 Relay ( 1 x Changeover) 24 V / 30 mA Reader Synchronisation 24 V / 2 A for Alarm Kit • Inputs – 1 Optocoupler – 1 Differential Input Max.
PAGE 47
OBID i-scan® Installation ID ISC.ANT1300/680-A Ambient Conditions • Temperature range – Operating – Storage –25°C to +50°C –25°C to +70°C Applicable Standards • RF approval – Europe – USA • EMC EN 300 330 FCC Part 15 EN 301 489 • Safety – Low Voltage Directive – Human Exposure UL 60950-1 (in preparation) EN 50364 * Persistent deformation after load release approx. 1 cm. ** Qty. 2 ID ISC.
PAGE 48
OBID i-scan® 5.2 Installation ID ISC.ANT1300/680-A Approval As per Section 4.7 Configuring the Reader in accordance with national RF regulations! 5.2.1 Europe (CE) This RF equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC dated March 99. Equipment Classification according to ETSI EN 300 330 and ETSI EN 301 489: Class 2 The technical data of the ID ISC.LRM2000 Reader built into the ID ISC.
PAGE 49
OBID i-scan® 5.2.2 Installation ID ISC.ANT1300/680-A USA (FCC) and Canada (IC) Product name: ID ISC.ANT1300/680 Antenna name: ID ISC.ANT1300/680 Type A Reader name: ID ISC.LRM2000-A FCC ID: IC: PJMANT1300680 6633A-ANT130068 Notice for USA and Canada This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions.
PAGE 50
OBID i-scan® Installation ID ISC.ANT1300/680-A 5.2.3 USA (UL) In preparation ! The following picture indicates the label position: FEIG ELECTRONIC GmbH Page 51 of 50 M71104-1e-ID-B.