User's Manual

2. Press Mode button on remote a second time. The
remote screen will now display "High" (1500 Watts).
The unit’s "High" light will illuminate and the unit will
run in this mode. In this mode the unit will
continuously run at 1500 Watts.
Note: While using the remote, the backlight function will
turn on when any button is pushed and will turn off after
10 seconds of non-use.
Note: Do not cover remote while in use, this may affect
the accuracy of the temperature reading.
Note: Do not place remote under lamps as the radiant
heat from the lamp may affect the accuracy of the
thermostat.
Note: Because heat rises, and the Galileo remote senses
temperature, Bionaire recommends that you do not locate
the Galileo remote higher than 4ft from the ground. By
locating the Galileo more than 4 ft from the ground, you will
get a less accurate temperature reading than under normal
circumstances.
THERMOSTAT OPERATION WITH REMOTE
1. Press Mode button on remote until the remote screen
displays "Auto" and "low". The "Set" temperature is
displayed next to the "Room" temp. The "Auto" light
on unit will illuminate. The unit will cycle on and off to
main tain the "Set" temperature. The default room temp
= 72ºF. In this mode the unit will run to maintain the
"Set" temperature.
2. Press Mode button on remote again. The remote
screen displays "Auto" and "high". The "Set"
temperature is displayed next to the "Room" temp.
The "Auto" light on unit stays illuminated. The unit will
cycle on and off to maintain the "Set" temperature at
high wattage (1500 Watts).
3. To turn unit "Off", press the Mode button and the LCD
will go blank (except for the "Room" temperature
display which is always displayed while batteries are in
the remote) and the unit will shut off.
Note: It is normal for the heater to cycle on and off as it
maintains the preset temperature. To prevent the unit from
cycling, you need to raise the thermostat setting.
ADJUSTING SET TEMP:
1. When in "Auto" mode, press the (+) button on the
remote. The "Set" number will increase with each
press. Hold the button down to scroll. The minimum
temp is 55ºF and the maximum is 85ºF. The unit scrolls
one digit at a time in a continuous loop. 55º, 56º…, 84º,
85º, 55º, 56º….
2. When in "Auto" mode, press the (-) button on the
remote to decrease the "Set" temperature. The
unit scrolls one digit at a time in a continuous loop.
UNIT OPERATION WITHOUT REMOTE
A. Remote and Unit are OFF:
1. Press the Mode button on the unit the first time. The
"Low" light illuminates and the unit runs in "Low" mode.
The power light turns on.
2. Press the Mode button a second time to run in "High"
mode (1500 Watts).
3. Press the Mode button a third time and the unit shuts
off.
Note: The "auto" light only illuminates when the unit is set
to "auto" mode by the remote.
B. Remote is ON and Unit is ON:
1. Press the Mode button on the unit. The unit will then
switch "Modes"; either from "Low" to "High", "High" to
"Off" or "Auto" to "Off" . The unit’s lights will reflect the
change. The Remote will display a different mode – the
mode in which it was left. If a button is pressed on the
Remote, the Remote’s signal will override the "Mode"
on the unit and the two will be back in sync.
TIMER FUNCTION:
To turn unit off while remote and unit are on (in low, high,
auto state).
1) Hold mode button for 2 seconds to unlock remote.
2) Push + and - together.
2.1) "timer" turns on. 1 Hr appears on the screen.
2.2) the current mode will remain displayed on the
screen ("low" or "high" or "auto")
3) Push + or - to adjust the number of hours the unit will
run before it shuts itself off.
3.1) you can choose from; 1, 2, 3, 4, 5, 6, 7, 8 hours
3.2) 1 through 8 will scroll in a continuous loop
4) After you have made your selection, "timer" flashes for
5 seconds after last button push of + or - then goes
6
7