GALILEO ™ digital heater MODEL BCH4138-U Read instructions before operating. Retain for future reference. Instruction Leaflet ☎ INFO-LINE If after having read this leaflet, you have any questions or comments on your heater, call 1-800-253-2764 in North America.
HEATER SAFETY PLEASE READ AND SAVE THESE IMPORTANT SAFEGUARDS. IMPORTANT INSTRUCTIONS When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1. Read all instructions before using the appliance. 2. To avoid fire or shock hazard, plug the appliance directly into a 120V AC electrical outlet. 3. The heater is hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces.
recommended by the manufacturer may cause fire, electric shock, or injury to persons. The use of attachments not recommended or sold by Bionaire® may cause hazards. 11. DO NOT use outdoors. 12. To prevent a possible fire, DO NOT block air intakes or exhaust in any manner. DO NOT use on soft surfaces, like a bed, where openings may become blocked. 13. To disconnect heater, set controls to OFF, then remove plug from outlet. 14.
FIRST USE ONLY: 1. Put batteries into Remote. The "Room" temperature is displayed at all times. (Use 3 AAA Alkaline batteries only, do not mix batteries) 2. Plug unit into outlet. The first time the unit is plugged in, it will beep every two seconds until it is synced with the remote. To sync unit with remote follow the below steps: Unlock remote. (This must be done before each use of the remote) To Unlock remote, hold down the mode button for 2 seconds until the lock symbol disappears on the screen.
display which is always displayed while batteries are in the remote) and the unit will shut off. Note: It is normal for the heater to cycle on and off as it maintains the preset temperature. To prevent the unit from cycling, you need to raise the thermostat setting. ADJUSTING SET TEMP: 1. When in “Auto” mode, press the (+) button on the remote. The “Set” number will increase with each press. Hold the button down to scroll. The minimum temp is 55ºF and the maximum is 85ºF.
1) Hold mode button for 2 seconds to unlock remote. 2) DO NOT push mode again as this will turn unit on. 3) Push + and - together. 3.1) Unit remains off. 3.2) "timer" and "auto - high" turns on and flashes on the remote, and 1 Hr appears on the screen 4) Push + or - to adjust the number of hours that will pass before it turns itself on. 4.1) you can choose from; 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16 hours 4.
WARRANTY Bionaire® warrants to the first retail purchaser, for TWO (2) YEARS from the date of original purchase, either to repair or replace at its option, without charge (parts and labor), any supplied or manufactured part of this heater which, upon inspection by an authorized service center, proves to have failed in normal use due to defects in material or workmanship, or at its option, to replace the unit.
recommended by the manufacturer may cause fire, electric shock, or injury to persons. The use of attachments not recommended or sold by Bionaire® may cause hazards. 11. DO NOT use outdoors. 12. To prevent a possible fire, DO NOT block air intakes or exhaust in any manner. DO NOT use on soft surfaces, like a bed, where openings may become blocked. 13. To disconnect heater, set controls to OFF, then remove plug from outlet. 14.
FIRST USE ONLY: 1. Put batteries into Remote. The "Room" temperature is displayed at all times. (Use 3 AAA Alkaline batteries only, do not mix batteries) 2. Plug unit into outlet. The first time the unit is plugged in, it will beep every two seconds until it is synced with the remote. To sync unit with remote follow the below steps: Unlock remote. (This must be done before each use of the remote) To Unlock remote, hold down the mode button for 2 seconds until the lock symbol disappears on the screen.
display which is always displayed while batteries are in the remote) and the unit will shut off. Note: It is normal for the heater to cycle on and off as it maintains the preset temperature. To prevent the unit from cycling, you need to raise the thermostat setting. ADJUSTING SET TEMP: 1. When in “Auto” mode, press the (+) button on the remote. The “Set” number will increase with each press. Hold the button down to scroll. The minimum temp is 55ºF and the maximum is 85ºF.
1) Hold mode button for 2 seconds to unlock remote. 2) DO NOT push mode again as this will turn unit on. 3) Push + and - together. 3.1) Unit remains off. 3.2) "timer" and "auto - high" turns on and flashes on the remote, and 1 Hr appears on the screen 4) Push + or - to adjust the number of hours that will pass before it turns itself on. 4.1) you can choose from; 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16 hours 4.
WARRANTY Bionaire® warrants to the first retail purchaser, for TWO (2) YEARS from the date of original purchase, either to repair or replace at its option, without charge (parts and labor), any supplied or manufactured part of this heater which, upon inspection by an authorized service center, proves to have failed in normal use due to defects in material or workmanship, or at its option, to replace the unit.
FCC Statement Warning: Note: This equipment has been tested and found to comply with the limits for digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, used and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference in to radiate communications.
