Manual

FEC FUSION Operations Manual
4.11 Tool Cable
Connection
•
Tools are connected to the
ducer preamp, motor
and
fication
number and should be connected to the corresponding
• Cables should be
supported to reduce fatigue points
allow the cable to move, but yet hold it in place. Cable tie
point leading to premature cable failure.
WARNING:
Do not make motor connections with the power on. Turn off all controller power
before attempting to connect or disconnect any motor cables
Recommended c
able length:
Maximum cable length:
Fusion Cable List
FEC Part #
FEB-1309-M5
Main Cable Straight Female Plug
FEB-1309-M10
Main Cable Straight Female
FEB-1309-M15
Main Cable Straight Female Plug
FEB-1311-M5
Main Cable 90 Degree Female Plug
FEB-1311-M10
Main Cable 90 Degree Female Plug
FEB-1311-M15
Main Cable 90 Degree Female Plug
FEB-1310-M1
Extension Cable Straight Female Plug
FEB-1310-M2
Extension Cable Straight Female Plug
FEB-1310-M3
Extension Cable Straight Female Plug
FEB-1310-M5
Extension Cable Straight Female Plug
FEB-1310-M10
Extension
FEB-1312-M1
Extension Cable 90
FEB-1312-M2
Extension Cable 90
FEB-1312-M3
Extension Cable 90
FEB-1312-M5
Extension Cable 90
FEB-1312-M10
Extension Cable 90
Wave Washer (Part # WAV
sired. The washer must be split and inserted by threading the washer
ers.
FEC FUSION Operations Manual
Chapter 4: System Setup and Wiring (Rev. 2.1)
Page 4-29
Connection
Tools are connected to the
controller using one
cable. One cable connects to the
and
resolver. Each cable should be labeled with a
specific
number and should be connected to the corresponding
controller
and
supported to reduce fatigue points
. Cable tie points
should be loose enough to
allow the cable to move, but yet hold it in place. Cable tie
points that are
too tight cause a stress
point leading to premature cable failure.
Do not make motor connections with the power on. Turn off all controller power
before attempting to connect or disconnect any motor cables
or tool damage may occur.
able length:
75’ or less.
100’ (must be free from Electrical Noise)
Cable Description Length
Main Cable Straight Female Plug
5 meter
Main Cable Straight Female
Plug
10 meter
Main Cable Straight Female Plug
15 meter
Main Cable 90 Degree Female Plug
5 meter
Main Cable 90 Degree Female Plug
10 meter
Main Cable 90 Degree Female Plug
15 meter
Extension Cable Straight Female Plug
1 meter
Extension Cable Straight Female Plug
2 meter
Extension Cable Straight Female Plug
3 meter
Extension Cable Straight Female Plug
5 meter
Extension
Cable Straight Female Plug
10 meter
Extension Cable 90
Degree Female Plug
1 meter
Extension Cable 90
Degree Female Plug
2 meter
Extension Cable 90
Degree Female Plug
3 meter
Extension Cable 90
Degree Female Plug
5 meter
Extension Cable 90
Degree Female Plug
10 meter
Wave Washer (Part # WAV
-
25036) can be used to tighten the tool side twist lock connector is d
sired. The washer must be split and inserted by threading the washer
underneath the twist lock rol
Chapter 4: System Setup and Wiring (Rev. 2.1)
cable. One cable connects to the
torque trans-
specific
spindle or identi-
and
tool.
should be loose enough to
too tight cause a stress
Do not make motor connections with the power on. Turn off all controller power
or tool damage may occur.
25036) can be used to tighten the tool side twist lock connector is d
e-
underneath the twist lock rol
l-