Owner's manual

enFORCE SAN Unit Operation Manual
PAGE 6 - 19
Cha
p
ter 6: S
y
stem O
p
eration
Data Number Conversion Table
Item
Parameter
Number
PARM
Data
Number D-
No
DATA
System
００ ００ Load unit number ０:ＫＮ 1: Klbs. 2: Metric Ton
００ ０１ ＳＰ version／copy between parameter <No change>
００ ０２ Amplifier Version <No change>
００ ０３ Function Version <No change>
００ ０４ Off Set Load
００ ０５ Distance Compensation ［mm］
００ ０６ No Load Current Limit 0～1023
００ ０７ Home Position Off Set ［mm］
００ ０８ Home Position Sensor／PLC Bank Select
００ ０９ Home position search time out 0.1[sec] unit
００ ０Ａ Distance Decimal / Deadman / Comm Speed / Timing Signal
００ ０Ｂ Approach Distance Limit／Load Cell Availability
００ ０Ｃ Current Load Conversion Ratio [%]
００ ０Ｄ Stroke Distance Limit／Load Hold Time Decimal Point
００ ０Ｅ MANUAL Speed ［mm/sec］
００ ０Ｆ Dynamic Hold / RS232C Output／Speed Decimal Point
Tool
Data
００ １０ Tool Num ber
００ １１ Tool CAL Load
００ １２ Tool CAL Voltage [Ｖ]
００ １３ Tool Zero Load Voltage [Ｖ]
<No change> ００ １４～１Ａ In House Control Data
Tool Typ e ００ ２０ Tool Num ber
０１～３２ ００ Press Mode (Press Method + Return Operation+ Judgment Operation)
Load
０１～３２ １０ Full-Scale Load
０１～３２ １１ Load Low Limit
０１～３２ １２ Load High Limit
０１～３２ １３ Target Load
０１～３２ １４ Press Speed Start Load
０１～３２ １５ Interference Check Load / Part Check Load High Limit
０１～３２ １６ Distance Measurement Start Load
０１～３２ １７ Part Check Load Low Limit
０１～３２ １８ Detection Start Load/Time Start Load (2
nd
Rate Start Load)
Distance
０１～３２ ２０ Distance Low Limit [mm]
０１～３２ ２１ Distance High Limit [mm]
０１～３２ ２２ Target Distance [mm]
０１～３２ ２３ Interference Check Distance / Part Check Distance [mm]
０１～３２ ２４ Press Speed Start Distance [mm]
Special Option
０１～３２ ３０ Advance Position ON Distance (1
st
Rate Low) [mm]
０１～３２ ３１ Advance Position OFF Distance (1
st
Rate High) [mm]
０１～３２ ３２ Return Position ON Distance (2
nd
Rate Low) [mm]
０１～３２ ３３ Return Position OFF Distance (2
nd
Rate High) [mm]
Time
０１～３２ ４０ Slow Start Time [sec]
０１～３２ ４１ 1
ST
Time High Limit [sec]
０１～３２ ４２ 2
ND
Time High Limit / Press Time [sec]
Speed
０１～３２ ５０ Slow Start Speed [mm/sec]
０１～３２ ５１ Approach Speed [mm/sec]
０１～３２ ５２ Part Search Speed [mm/sec]
０１～３２ ５３ Press Speed [mm/sec]
０１～３２ ５４ Return Speed [mm/sec]
０１～３２ ６０ Approach Distance [mm]
Special Setting
０１～３２ ６１ Load Hold Time [sec]
０１～３２ ６２ Job Start Position [mm]
０１～３２ ６３ Load Change
０１～３２ ６４ Distance Off Set [mm]