Chapter 2: Specifications PAGE 2 - 1
Chapter 2: Specifications enFORCE Operation Manual 2.1 System Specifications Power Supply Voltage 180VAC ~ 242VAC, 3 phase, 50/60Hz Operating Conditions Temperature: Humidity: Operating Range Duty Cycle less than 60% Storage Conditions Temperature: Humidity: -5 ~ 55℃ (23 ~ 131℉) Below 90%, no condensation Shipping Conditions Temperature: Humidity: -5 ~ 55℃ (23 ~ 131℉) Below 90%, no condensation Press Accuracy From 1/2 to full scale - 3σ less than 3% scatter of target load.
Chapter 2: Specifications enFORCE Operation Manual 2.2 SAN Unit Specifications 32 bit RISC (Reduced Instruction Set CPU) RS485 (2 Ports) – 1 for DSP User Console Software Flash ROM CPU: Data Communication: Parameter / Firmware Storage: SAN Unit Type Motor Type SAN3 - 24S ＲＭ１ SAN Unit Input Power SAN Unit Frequency MAX.
Chapter 2: Specifications 2.2.2 enFORCE Operation Manual SAN Unit Dimensions SAN3-24S, SAN3-40S Mounting: Top Bottom 1 place 2 places Weight: SAN3-24S - 1.4 kg SAN3-40S - 1.8 kg #8-32 screw #8-32 screw Note: The diagram shown above reflects dimensions for the SAN3-40S. The SAN3-24S does not have a heat sink plate so the width is 60mm as opposed to 74mm.
Chapter 2: Specifications enFORCE Operation Manual SAN3-120S Mounting: Top Bottom 2 places #8-32 screw 2 places #8-32 screw Weight: SAN3-120S - 3.6kg.
Chapter 2: Specifications enFORCE Operation Manual 2.3 Press Tool 2.3.1 Part Number Breakdown DPT-[151]R[3][ ]-[25][F][S][B]-[00][A] A BC D E F G H I (A) PRESS FORCE (In Metric Tons) 020=0.2ton 050=0.5ton 101=1.0ton 151=1.5ton 201=2.0ton 301=3.0ton (B) MOTOR 1 = RM1A 2A = RM2A 3 = RM3A 4 = RM4 4H = RM4H 5 = RM5 (C) REVISION BLANK = STANDARD MOTOR A, 3, ETC. = ALPHA NUMERIC REVISION CODE (D) STROKE 15 = 150mm 25 = 250mm (E) PRESS TYPE F = PRESSING (Holding time <1sec.
Chapter 2: Specifications enFORCE Operation Manual 2.3.2 Tool Specifications Permanent magnet DC Inline Load Cell High Resolution Resolver Motor: Force Monitor: Distance Monitor: List of standard tool for press-fitting (F type) Use the following tools when operating with instantaneous load. Tool No. Tool type Maximum load [KN] Maximum speed Minimum speed [mm/sec] [mm/sec] 30 DPT-021R1-**F 1.96 416.6 0.4 31 DPT-051R2-**F 4.90 333.3 0.3 32 DPT-101R3-**F 9.81 277.7 0.
Chapter 2: Specifications enFORCE Operation Manual 2.3.
Chapter 2: Specifications enFORCE Operation Manual 2.4 Functions • Pressing Function The following press control methods can be selected for the enFORCE System. 1. 2. 3. 4. 5. 6. 7. 8. 9. Load Control Distance Control Specified Point Load Judgment Load Rise Detection Time Controlled Press Load Drop Detection Specified Range Peak Load Judgment Load Drop Detection (Point Stop) Distance Control with Load Limit Load and Distance can be monitored in any configuration.
Chapter 2: Specifications enFORCE Operation Manual PAGE 2 - 10
