Chapter 7: System Operation Chapter 7: System Operation Page 7-1
Chapter 7: System Operation 7.0 sYSTEM OPERATION AT initial power on, the AFC1200 System performs a series of self-checks which requires approximately 30 seconds to complete. DURINg this time, the following events take place: 1. THe AFC1200 ISA MAIn Controller UNIT performs a Power On Self-Test (POST). 2. THe AFC1200 ISA MAIN UNIT loads the operational program from EPROM. 3. COmmunication is established between the ISA MAIN CONTROLler UNIT and connected AXIS Controller UNIT(s). 4.
Chapter 7: System Operation 7.0.1 normal Operation if the System's preset data is already configured for machine operation, no further setup is required. To choose the display screen you wish to view, proceed as follows: 1. The cursor on the menu bar is shown as a purple highlight. Move the cursor to "MENU" using the keypad [←] [→] keys, and then press the [↵] key. "DISPLAY MENU" will appear and show the existing display screen in a cyan colored highlight. 2.
Chapter 7: System Operation (normally CCW) rotation. The function of this screen is to view the preset limit parameters of all nutrunners connected to the System. data that has been preset on the "Set Parameter" screen is displayed in a table format on this page. 7.2 LIMIT PARAMETER: 7.3 FASTENING DATA: Displays the fastening results of the previous operation. 7.
Chapter 7: System Operation 7.0.2 INITIAL OPERATION Prior to entering the initial configuration data, turn the key switch located on the front of the Main Unit from "RUN" mode to "PROGRAM" mode. If data entry is attempted without turning the key switch to "PROGRAM" mode, the error message "RUN MODE" is displayed at the bottom of the screen. The following data represents the recommended procedure for setting initial data presets : 1. MACHINE CONFIGURATION (SECTION 7.
Chapter 7: System Operation 7.0.3 BACKup OPERATION - PRESET FILE UTILITY Prior to loading configuration data, turn the key switch located on the front of the Main Unit from "RUN" mode to "PROGRAM" mode. If data loading is attempted without turning the key switch to "PROGRAM" mode, the error message "RUN MODE" is displayed at the bottom of the screen. REFER TO SECTION 7.14.0. FOR DETAILED "PRESET FILE UTILITY" OPERATION The following represents the recommended order of loading for data presets : 1.
Chapter 7: System Operation 7.0.4 standard OPERATIONal Procedures The following items are standard operational procedures utilized throughout the entire AFC1200 Fastening System program. 1. Initiation of a change in preset data: To initiate a change in the preset data in any of the 15 sections of the AFC1200 program, press the keypad SEL key. The cursor will move from the Menu bar to the lower portion of the screen. The Run/Program switch must be set to Program to change fastening presets. 2.
Chapter 7: System Operation 4. Cursor movements: The [←] [→] keys are used to select the functions from the menu [↵] key to activate the function. Use bar. After selecting (highlighting) an item, depress the of the [↑] [↓] and [←] [→] keys may be required to further select the desired operation or value. These four arrow keys are used throughout the AFC1200 program to provide up, down, left, and right cursor movement. Additionally, the [↑] [↓] keys are sometimes used to scroll through selectable data. 5.
Chapter 7: System Operation 7.1 Set Parameter tHe functions of these screens are to input the fastening method, the tool type, and all fastening, speed, and reverse parameters. 7.1.1 TABLE OF CONTENTS 7.1.1. 7.1.2. 7.1.3. 7.1.4. 7.1.5. 7.1.6. 7.1.7. 7.1.8. 7.1.9. 7.1.10.
Chapter 7: System Operation 2-3b. THE pulldown menu will display three input mode selections: [FASTENING] FASTENINg parameter set screen [SPEED] Speed parameter set screen [REVERSE] REverse parameter set screen 2-3c. Using the [↑] [↓] keys, select the desired input mode and depress the [↵] key. The selected input mode screen will now be displayed. FIG. 7-1-2-3 set parameter [INPUT MODE] 7.1.
Chapter 7: System Operation FIG. 7-1-3-1 set parameter Fastening method selection 3-2. SElect TOOL TYPe 3-2a. Move the cursor to the [FULL SCALE TORQUE] position on the screen using the [↓] key. The numerical value below [FULL SCALE TORQUE] will be highlighted. DEPress the [↵] key and a pulldown menu will appear which displays the tool type selection. [→] keys, scroll through the selection until the correct tool type appears. DEpress the [↵] key, and the highlighted full scale torque value will 3-2b.
Chapter 7: System Operation FIG. 7-1-3-3 set parameter data presetting 3-4. SELECT CLEAR COMMand 3-4a. MOve the cursor on the menu bar to [CLEAR] using the [←] depress the [↵] key. Two (2) options will be given [→] keys and 3-4b. [SCREEN DATA CLEAR] - clears all data on the screen except for the Full Scale Torque value and the fastening Method (Torque, Angle, etc.) [PARAMETER NO. DATA CLEAR] - clears all data for the Parameter No.
Chapter 7: System Operation selected). THE screen will change to display the "SET PARAMETER (SPEED)" screen. 4-1b. DEPress the [SEL] key and the cursor will move to the first position for numerical entry. FIG. 7-1-4-1 set parameter [SPEED ] 4-2 INPUT SPEED PARAMETER DATA 4-2a. key. ENTer the numerical data required for the selected item and depress the [↵] 4-2b. The cursor will move to the next item to be entered until all items have been entered. 4-2c.
Chapter 7: System Operation 4-2d. SELect YES or NO using the [←] [→] keys, then depress the [↵] key. Refer to the "VOCABULARY LIST" sections 7.1.6 through 7.1.10 for details of presetting for each fastening method, and to Chapter 6 for fastening instructions. NOTES: 1. IF incorrect numerical data is entered, the System will display "INPUT ERROR". 2. "FReerun Time" and "Initial Time" may be set in either seconds or revolutions. 3.
Chapter 7: System Operation 7.1.5 REVERSE PARAMETER SETUP THE function of this screen is to preset the following parameters: REVERSE SPEED REVERSE TIME [RPM] [SEC] REVERSE REVOLUTIONS 5-1 REVERSE TORQUE REVERSE ANGLE [TQ] [DEG] [REV] SELECT INPUT MODE 5-1a. MOVe the cursor on the menu bar to [INPUT MODE], select [REVERSE] and depress the [↵] key. THe screen displayed will be the "SET PARAMETER (REVERSE)" screen. Check the Parameter Number to ensure that the correct number has been selected.
Chapter 7: System Operation 5-2 INPUT SPEED PARAMETER DATA 5-2a. key. Enter the numerical data required for the selected item and depress the [↵] 5-2b. The cursor will move to the next item to be entered until all items have been entered. 5-2c. After all items have been entered or changed, depress the [SEL] key. The question "DATA CHANGE OK?" will appear in the lower right hand corner. 5-2d. Select YES or NO using the [←] [→] keys, and depress the [↵] key. Refer to the "VOCABULARY LIST" Sections 7.1.
Chapter 7: System Operation 7.1.6 vOCABULARY LIST 1 [FASTENING] TORQUE CONTROL FIG.
Chapter 7: System Operation 1ST TORQUE SEat torque (1st Torque), end of 1st TORQUE RAte measurement, start of 2nd TORQUE Rate measurement CROSSOVER RATE 2 TORQUE END of 2nd TORQUE Rate measurement, start of 3rd torque Rate measurement 2ND TORQUE TORque for 2nd Step in multi-step fastening 3RD TORQUE TORque for 3rd Step in multi-step fastening STD TORQUE FINal target torque in TORQUE Control mode, end of 3rd TORQUE RAte measurement HIGH TORQUE HIgh torque limit LOW TORQUE LOw torque limit HIGH
Chapter 7: System Operation 7.1.7 VOCABULARY LIST 2 [FASTENING] ANGLE CONTROL FIG.
Chapter 7: System Operation 1ST TORQUE SEat torque (1st Torque), end of 1st TORQUE RATE measurement, start of 2nd TORQUE Rate measurement NOTE: EITher 1st tORQUE or 1st angle may set, but not both.
Chapter 7: System Operation 7.1.8 VOCABULARY LIST 3 [FASTENING] YIELD CONTROL FIG.
Chapter 7: System Operation LENGTH Permanent elongation, calculated automatically if angle is entered ANGLE Rotation into yield, calculated automatically if length is entered YIELD RATE Final target TORQUE RAte for a period equal to the preset angle CONSTANT Compensation factor for permanent elongation (default = 1.00) NOTE: CROSsover points can be set in either torque or angle, but not both.
Chapter 7: System Operation 1ST TORQUE RATE LOW LOw limit for 1st TORQUE RATE 2ND TORQUE RATE HIGH HIgh limit for 2nd TORQUE RATE 2ND TORQUE RATE LOW Low limit for 2nd TORQUE RATE 3RD TORQUE RATE HIGH High limit for 3rd TORQUE RATE 3RD TORQUE RATE LOW Low limit for 3rd TORQUE RATE Page 7-23
Chapter 7: System Operation 7.1.9 VOCABULARY LIST 4 [SPEED] FIG.
Chapter 7: System Operation Note: Set eITHer seconds [SEC] or revolutions [REV] for freerun and initial time, but not both. 7.1.10 VOCABULARY LIST 5 [REVERSE] FIG. 7-1-10 set parameter [REVERSE] NO. 1 REVERSE NUTrunner reverse speed during mode No. 1 NO. 2 REVERSE Nutrunner reverse speed during mode No. 2 NO. 3 REVERSE NUTrunner reverse speed during mode No. 3 NO. 1 REVERSE TIME [SEC] -- Time (in seconds) for No. 1 Reverse mode [REV] -- Number of revolutions for No. 1 Reverse mode NO.
Chapter 7: System Operation TORQUE REVERSE ANGLE Preset angle value for REVERSE ANGLE CONtrol REVERSE ANGLE HIGH High limit for REVERSE ANGLE REVERSE ANGLE LOW LOw limit for REVERSE ANGLE REVERSE TORQUE HIGH High torque limit for REVERSE ANGLE COntrol REVERSE TORQUE LOW LOw torque limit for REVERSE ANGLE COntrol Page 7-26
Chapter 7: System Operation 7.2 liMIT PARAMETEr THE function of this screen is to view the preset limit parameters of all nutrunners connected to the System. 7.2.1 TABLE OF CONTENTS 7.2.1. 7.2.2. 7.2.3. 7.2.4. 7.2.5. TAble of Contents for LIMIT PARAMETER screens Sequence Select SEt Mode DISPLAy Explanation SCREEn Operation 7.2.2 sEQUENCE SELECT 2-1. AFTer selecting [LIMIT PARAMETER] from the menu bar, depress the [↵] key and the screen will change to the "PARAMETER ( )" display screen. 2-2.
Chapter 7: System Operation FIG. 7-2-3 limit parameter [SET MODE] 7.2.4 DISPLAY EXPLANATION 4-1. [JUDGMENT] DISPlay of all pRESET jUDGMENT lIMits (16 items) FIG.
Chapter 7: System Operation 4-2. [CONTROL] DIsplay of all preset control vALUes (23 items) FIG. 7-2-4-2a limit PARAMETER (CONTROL) PAGE ONE FIG.
Chapter 7: System Operation 4-3. [SPEED/TIME] DISPlay of all PRESET SPEED AND TIME LImits (18 items) FIG. 7-2-4-3a limit PARAMETER (SPEED/TIME) PAGE ONE FIG.
Chapter 7: System Operation 7.2.5 SCREEN OPERATION 5-1. Each limit parameter screen is capable of displaying up to 16 items. ON screens that include more than 16 items, scrolling is necessary. 5-2. USing the [←] [→] keys move the cursor to [UP], [DOWN], [LEFT] or [RIGHT] and depress the [↵] key to scroll. 5-3. THe [UP] [DOWN] position will scroll all limit parameters for each spindle. THE [LEFT] [RIGHT] position will scroll all 24 spindles. 5-4.
Chapter 7: System Operation 7.3 FASTENING DATA THe function of this screen is to view real time spindle status (ACCEPT / REJECT / ABNORMAL), fastening time, and fastening data. 7.3.1 TABLE OF CONTENTS 7.3.1. 7.3.2. 7.3.3. 7.3.4. TABle of Contents for FASTENING DATa screens DAta DISPLAY SELECTion SCReen Operation Vocabulary List [FASTENING DATA] 7.3.2 datA DISPLAY SELECTION 2-1.
Chapter 7: System Operation FIG. 7-3-2 fastening data, data display selection 7.3.3 scREEN OPERATION 3-1. EACH fastening data screen is capable of displaying up to (14) items. ON screens that include more than (14) items, scrolling is necessary. 3-2. USing the [←] [→] keys move the cursor to [UP], [DOWN], [LEFT] or [RIGHT] and depress the [↵] key to scroll. 3-3. The [UP] [DOWN] position will scroll all fastening data for each spindle. THE [LEFT] [RIGHT] position will scroll all (24) spindles. 3-4.
Chapter 7: System Operation 7.3.
Chapter 7: System Operation 3RD RATE INC TORQUE CHange in torque as measured from CROSSOVER RATE2 TORQue/Angle until completion of fastening 3RD RATE INC ANGLE CHange in angle as measured from CROSSOVER RATE 2 Torque/Angle until completion of fastening 1ST STEP TIME amoUnt of time used to complete the 1st Step of fastening FINAL STEP TIME aMount of time used to complete the FINAL Step of fastening REVERSE PEAK TORQUE HIGhest torque value measured during reverse operations DUTY CYCLE RATIO % 100 =
Chapter 7: System Operation 7.4 FASTENING TORQUE CURVE THE function of this screen is to view TORQUE/ANGLE and TORQUE/TIME fastening curves. 7.4.1 table OF CONTENTS 7.4.1. 7.4.2. 7.4.3. 7.4.4. 7.4.5. 7.4.6. TABLE of Contents for FASTENING TORQUE CUrve screens SPINdle SElection SCALe SELECTion DAtabase Selection PRint FASTENING CURVE Graph / Screen Description 7.4.2 SPINDLE SELECTION Note: 2-1.
Chapter 7: System Operation FIG.
Chapter 7: System Operation 7.4.3 SCALE SELECTIOn 3-1. MOVe the cursor on the menu bar to [SCALE] using the [←] [→] keys and depress the [↵] key. THE Scale pulldown menu will appear with the cursor flashing at the first set position. 3-2. There are fOur (4) selectable items as detailed below. Two (2) of the items relate to the TORQUE/ANgle curve, and the other two (2) relate to the TORQUE/TIme curve.
Chapter 7: System Operation Note: If changes are made to this pulldown menu setup, the System must be cycled before the Fastening Curve will display in accordance with the new parameters. 7.4.4 DATA BASE SELECTION 4-1. To configure the Fastening Curve screen to display either a Torque / Angle or Torque / Time curve, mOVe the cursor on the menu bar to DATA BASE using the [←] [→] keys, and depress the [↵] key. 4-2. THE DATA BASE pulldown menu will appear.
Chapter 7: System Operation 7.4.6 Graph / Screen description THe FASTENING CURVe screen diplays Torque information plotted along the vertical or "Y" axis, and either Angle or Time information is plotted on the horizontal or "X" axis. An auxilliary "accept" window is displayed in the plot area as a green box. The High and Low Torque presets from the Set Parameter screen are used to automatically set the height of the window.
Chapter 7: System Operation SCREEN DISPLAY SETTING SETTING RESULTS Divide(Angle) 1 For each one (1) degree of rotation (angle), one of the 200 points will be plotted (see "Angle Scale", above). Spindle No. 01, 02, & 03 chosen (Spindle Select pulldown). Note: All spindles are using the same Parameter Number, as required. Up to five (5) spindles can display a curve at the same time, each in a different color. If Spindle No. 02 or 03 had a different Parameter Number, it would not display.
Chapter 7: System Operation 7.5 SET SEQUENCE THe function of this screen is to setup the fastening sequences for all spindles. 7.5.1 TABLE OF CONTENTS 7.5.1. Table of Contents for Set Sequence screens 7.5.2. SEQUence Select 7.5.3. SPindle Setup 7.5.4. SEQuence Setup 7.5.5. SEQUENce Function (FUN) Explanation 7.5.6. SEQUENCe Data (DAT) Explanation 7.5.7. copy FUNCTION (Spindle to spindle) 7.5.8. sequence coPY FUNCTION (Sequence to sequence) 7.5.9. SEquence CLEAR FUNction 7.5.10.
Chapter 7: System Operation 3-3. USIng the [←] [→] keys, move the cursor to the "GP" (GROUP FASTENING) heading. Enter the group number which corresponds with the spindle number selected using the numerical keys (group numbers 01 thru 24 can be used). Depress the [↵] key after selection and before moving the cursor. 3-4. USINg the [←] [→] keys, move the cursor to the "PN" (PARAMETER NUMBER) heading. Using the numerical keys, enter the fastening parameters to be used.
Chapter 7: System Operation 7.5.4 SEQUENCE SETUP EACh spindle has 32 possible fastening steps which are designated stage 01 thru Stage 32. EACh stage requires two preset items; one for the FUNCTION [FUN] of the stage and one for the action or DATA [DAT] of each stage. Depressing the [±] key toggles the data entry method between the insert (INS) and replacement (REP) mode. The [DEL] key will delete the selected stage and shift all remaining stages left. 4-1.
Chapter 7: System Operation FIG. 7-5-4-2a set sequence, sequence setup (data) for functions 1-10 FIG.
Chapter 7: System Operation 4-3. MOVe the cursor to the next stage and repeat steps one and two until all desired stages are completed. DEPRESS the [SEL] key and the question "DATA CHANGE OK?" will appear for confirmation. USINg the [←] [→] keys, select YES or NO and depress the [↵] key. 7.5.5 SEQUENCE FUNCTION (FUN) EXPLANATION 1: [1ST] 1ST STEP tHE first step in multi-step fastening from zero torque to 1st TOrque or 1st ANgle.
Chapter 7: System Operation 18: [FST] FLAG SET 01 THRU 99 01 thru 99 tenths can be preset. THIs function is used to set a flag during the fastening sequence. Up to 99 flag sets may be set. TYpical use is sequential rundown. 19: [FCL] FLAG CLEAR THIS function is used to clear the flags set [FST] during the 01 THRU 99 fastening sequence when necessary. 20 :[FCK] FLAG CHECk THIs function is used to delay the fastening sequence until 01 THRU 99 the specified flag sets have been completed.
Chapter 7: System Operation 7-2. DEPRess the [↵] key and the copy pulldown menu will appear with the cursor flashing at the "COPY FROM SPINDLE NO." position. 7-3. USing the numerical keys insert the SPINDLE NO. to be copied. 7-4. USing the [↑] [↓] keys move the cursor to "COPY TO SPINDLE NO." THe cursor will be flashing at the "COPY TO SPINDLE NO." position. 7-5. USINg the numerical keys insert the SPINDLE NO. to be copied to or select the "ALL SPINDLES" option and depress the [↵] key.
Chapter 7: System Operation FIG. 7-5-8 set sequence, sequence copy function 7.5.9 sEQUENCE CLEAR FUNCTION THe SEQUENCE CLEar function has two modes for removing the sequence. EAch spindle may be deleted individually, or all spindles may be totally cleared. 9-1. PLACe the RUN/PROGRAM key in the PROGRAM position and move the cursor on the menu bar to [CLEAR] using the [←] [→] keys. 9-2. DEpress the [↵] key and the [CLEAR] pulldown window will appear with the cursor flashing at the [CLEAR SPINDLE NO.
Chapter 7: System Operation 10-2. USIng the [←] [→] keys, move the cursor to [UP], [DOWN], [LEFT], or [RIGHT] and depress the [↵] key to scroll. 10-3. The [UP] [DOWN] position will scroll seven (7) stages of the fastening sequence for each spindle. THe [LEFT] [RIGHT] position will scroll the sequence stages for up to 18 spindles. 10-4. TO print the fastening sequence for all spindles, move the cursor on the menu bar to [PRINT] and depress the [↵] key.
Chapter 7: System Operation 7.6 SEQUENCE INDICATION THE function of this screen is to monitor the fastening sequence as the fastening is in process. 7.6.1 TABLE OF CONTENTS 7.6.1. 7.6.2. 7.6.3. 7.6.4. TABLE of Contents for SEQUENCE INDICATION screens SCREEN EXPLANATION SEQUENCE SELECT SCREEN SCROLLING AND PRINT FUNCTIONs 7.6.2 sCREEN EXPLANATION 2-1. THE SEQUENCE INDICation screen will monitor the actual operation of each fastening to assure that each sequence step is being completed.
Chapter 7: System Operation 7.6.3 sEQUENCE SELECT 3-1. MOve the cursor on the menu bar to the [SEQUENCE SELECT] position and depress the [↵] key. THE pulldown menu will display the SEQUENCE NO. 3-2. USINg the [←] [→] keys, select the desired sequence to be viewed and depress the [↵] key. THe screen will change to the selected sequence, and display the preset sequence. THe SEQUENCE NO. will be displayed in the upper right hand corner. FIG. 7-6-3 sequence indication sequence select 7.6.
Chapter 7: System Operation 7.7 STORED DATA THe function of this screen is to view previous fastening data and an abbreviated SPC program that includes 6 sigma (6 ) and CPk. 7.7.1 TABLE OF CONTENTS 7.7.1. 7.7.2. 7.7.3. 7.7.4. TAble of COntents for STORED DAta screens SCREEN EXPLANATION INDICATION SELECT SCREEN SCROLLING aND PRINT FUNCTIONs 7.7.2 SCREEN EXPLANATION 2-1. THE STORED Data screen displays the previous data for a pre-selected spindle number and sequence number.
Chapter 7: System Operation FIG. 7-7-2 stored dATA screen 7.7.3 INDICATION SELECT 3-1. 3-2. MOve the cursor on the menu bar to [INDICATION SELECT] using the [←] [→] keys and depress the [↵] key. THe pulldown window for INDICATION SELEct will open. USe the [↑] [↓] keys to move the cursor to the desired position for selecting the following: [SEQUENCE No.] 1-8 [SPINDLE No.] 1-24 [STORED DATA No.
Chapter 7: System Operation 3-3. Use the [←] [→] keys to change sequence number, spindle number, and data format selection. 3-4. USe the numerical keys to enter the desired stored data number. 3-5. Depress the [↵] key after making selections and the screen will automatically change to display the selected data. 3-6. Use the [←] [→] keys to select [STATISTICS] from the menu bar. Select [START] to calculate the two right columns of the stored data screen.
Chapter 7: System Operation Notes: 1. SYStem must be cycled prior to setting [INDICATION SELECT] functions. 2. A minimum of (7) fastening cycles must be completed before the statistics (6 / CPk) are calculated and displayed. 3. A maximum of 500 cycles of data are stored for each spindle, however the number of cycles stored varies depending on the number of spindles connected.
Chapter 7: System Operation 7.8 sTORED DATA COUNt THe function of this screen is to view the total amount of accept, reject, abnormal and bypassed fastening cycles. 7.8.1 TABLE OF CONTENTS 7.8.1 7.8.2. 7.8.3. 7.8.4. Table of Contents for Stored Data Count screens SCREEN EXPLANATION SEQUENCE SELECT CLEAR aND PRINT FUNCTIONS 7.8.2 SCREEN EXPLANATION 2-1. THIS screen displays the data count for accept, reject, abnormal, and bypass fastenings for all spindles. 2-2.
Chapter 7: System Operation 7.8.3 SEQUENCE SELECT 3-1. 3-2. Move the cursor on the menu bar to the [SEQUENCE SELECT] using the [←] [→] keys and depress the [↵] key. THe pulldown menu for SEQUENCE SELEct will appear. USIng the [←] [→] keys, select the desired Sequence (1-8) and depress the [↵] key. THe screen will automatically change to display the STORED DATA COUNT information for the selected Sequence. FIG. 7-8-3 STORED DATA sequence select 7.8.4 CLEAR AND PRINT FUNCTIONS 4-1.
Chapter 7: System Operation 7.9 SYSTEM CONFIGURATION The functions of these screens are to configure the System communication for the RS422, RS232C, and Centronics parallel ports. 7.9.1 TABLE OF CONTENTS 7.9.1. 7.9.2. 7.9.3. 7.9.4. 7.9.5. 7.9.6. 7.9.7.
Chapter 7: System Operation 2-2. DATE and TIme / RS422 PORT [SYSTEM CONFIGURATION (2)] 2-2a. DATE and TIme the System date and time is configured and set via the upper half of [SYSTEM CONFIGURATION (2)]. DATE: **/**/** TIME: **/**/** mm/dd/yy hh:mm:ss 2-2b. RS422 PORT (System Option) BAUD RATE : 1200 BPS (2400, 4800, 9600, 19200) the communications baud rate for this port may be set to one of five common values. CHARACTER : 7 BIT (8 BIT) Character length may be set to either seven or eight bits.
Chapter 7: System Operation FIG.
Chapter 7: System Operation 2-3. RS232C PORT (CH1) [SYSTEM CONFIGURATION (3)] FASTENING DATA PRINT OUT : NO (YES) the print out of fastening data may be enabled or disabled via this function. DATA SELECT : ALL (ACCEPT, REJECT, ACCEPT & REJECT) specific fastening data types may be printed out by setting this delimiter. HEADER PRINT OUT MODE : NO PRINT OUT (POWER ON, FORM FEED, FASTENING PRINT OUT) The header may be printed out for any of the selection options.
Chapter 7: System Operation 2-4. RS232C PORT (CH2) [SYSTEM CONFIGURATION (4)] BAUD RATE : 1200 BPS (2400, 4800, 9600, 19200) the communications baud rate for this port may be set to one of five common values. CHARACTER : 7 BIT (8 BIT) Character length may be set to either seven or eight bits. PARITY : EVEN (ODD, NO PARITY) parity may be set to odd, even, or no parity. STOP BIT : 1 BIT(S) 2 BIT(S) stop bits may be set to either one or two. FIG.
Chapter 7: System Operation 2-6 header and line format for [SYSTEM CONFIGURATION (1) & (2) & (3)] 2-6a. SCreens (1), (2), and (3) have the capability of configuring the header and line formats for the Parallel Centronics, RS422, and RS232C output ports, respectively. The Header Format and Line Format areas shown below are part of each of the System Configuration screens (1), (2), and (3). the following information applies to all three screens. 2-6b.
Chapter 7: System Operation FIG.
Chapter 7: System Operation 7.9.3 SCREEN OPERATION [SYSTEM CONFIGURATION (1)] 3-1. After selecting [SYSTEM CONFIGURATION] from the menu bar, move the cursor on the menu bar to [PAGE UP] or [PAGE DOWN] and depress the [↵] key until the screen displays [SYSTEM CONFIGURATION (1)]. DEpress the [SEL] key. THe screen will change to the set mode with the first item (FASTENING DATA PRINT OUT : YES/NO) highlighted. 3-2.
Chapter 7: System Operation 7.9.4 SCREEN OPERATION [SYSTEM CONFIGURATION (2)] 4-1. After selecting [SYSTEM CONFIGURATION] from the menu bar, move the cursor on the menu bar to [PAGE UP] or [PAGE DOWN] and depress the [↵] key until the screen displays [SYSTEM CONFIGURATION (2)]. DEpress the [SEL] key. THe screen will change to the set mode with the first item (DATE :??/??/??) highlighted. 4-2. To change the date and time, use the numerical keys and the [←] [→] keys.
Chapter 7: System Operation 7.9.5 SCREEN OPERATION [SYSTEM CONFIGURATION (3)] 5-1. After selecting [SYSTEM CONFIGURATION] from the menu bar, move the cursor on the menu bar to [PAGE UP] or [PAGE DOWN] and depress the [↵] key until the screen displays [SYSTEM CONFIGURATION (3)]. DEpress the [SEL] key. THe screen will change to the set mode with the first item (FASTENING DATA PRINT OUT : YES/NO) highlighted. 5-2.
Chapter 7: System Operation 7.9.6 SCREEN OPERATION [SYSTEM CONFIGURATION (4)] 6-1. After selecting [SYSTEM CONFIGURATION] from the menu bar, move the cursor on the menu bar to [PAGE UP] or [PAGE DOWN] and depress the [↵] key until the screen displays [SYSTEM CONFIGURATION (4)]. DEpress the [SEL] key. THe screen will change to the set mode with the first item (BAUD RATE:) highlighted. 6-2.
Chapter 7: System Operation FIG. 7-9-6b Input Data Format [SYSTEM CONFIGURATION (4)] NOTE: The input data stream must be a formatted input that will always be received in the same configuration. Example: the first five characters in the input data stream are part number. the next character is a space (20 hex). the next six characters represent the part serial number. (Refer to the first row (00) of the chart in Figure 7-9-6b, and to the related description below.) 1.
Chapter 7: System Operation 7.9.7 header and line format - System Configuration Screens (1), (2), and (3) 7-1. After selecting [SYSTEM CONFIGURATION] from the menu bar, move the cursor on the menu bar to [PAGE UP] or [PAGE DOWN] and depress the [↵] key until the screen displays [SYSTEM CONFIGURATION (1), (2) or (3)] as desired. DEpress the [SEL] key. THe screen will change to the set mode with the first item (FASTENING DATA PRINT OUT : YES/NO) highlighted. 7-2.
Chapter 7: System Operation 7-4. SElect the desired character/data from the displayed table by using the [↑] [↓] and [←] [→] keys. depress the [↵] key to paste the selected item into the selected position on the HEADER FORMAT. Repeat this operation until the header is formatted as desired. the last item to appear on each line must be the "END OF PRINT" character, represented on the format line as a ";" bordered in red. 7-5.
Chapter 7: System Operation 7.10 MACHINE CONFIGURATION The function of this screen is to preset basic identification data related to each machine. 7.10.1 TABLE OF CONTENTS 7.10.1. TABLe of Contents for MACHINE CONFIGuration screens 7.10.2. SCREen Explanation 7.10.3. SCreen OPERATION/PRINT FUNCTION 7.10.2 SCREEN EXPLANATION 2-1.
Chapter 7: System Operation 7.10.3 SCREEN OPERATION 3-1. AFTer selecting the [MACHINE CONFIGURATION] screen from the menu bar, depress the [SEL] key and the first field will appear with a highlighted background. 3-2. USe the [↑] [↓] keys to move the highlighted cursor to the desired position. 3-3. TO input an address in the machine address field or the head address fields, move the highlighted cursor to the desired position and depress the [↵] key.
Chapter 7: System Operation 7.11 PREAMP EEPROM DATA The function of this screen is to view the information programmed on the tool preamp EEPROM. 7.11.1 TABLE OF CONTENTS 7.11.1. Table of COntents for PReamp EEPROM Data screens 7.11.2. Screen Explanation 7.11.3. SCreen OPERATION/PRINT FUNction 7.11.2 SCREEN EXPLANATION 2-1. THe PREamp EEPROM DATa screen displays the information written to the EEPROM mounted in the tool preamp connector housing.
Chapter 7: System Operation 7.12 tORQUE CALIBRATion The function of this screen is to adjust the calibration (Cal) value of the FEC INC. torque transducer with a master torque sensor. 7.12.1 TABLE OF CONTENTS 7.12.1. TAble of Contents for TORQUE Calibration screens 7.12.2. SCreen Explanation 7.12.3. SCReen OPERATION/PRINT FUNCTION 7.12.2 SCREEN EXPLANATION 2-1. The TORQUE CALIbration screen is made up of two columns capable of listing 12 tools in each column.
Chapter 7: System Operation 7.12.3 SCREEN OPERATION 3-1. TO adjust the calibration, a simple calculation must be performed. With the master torque transducer in-line with the FEC torque transducer, perform 10 fastenings and collect the fastening torque data from the FEC and the master transducer. 3-2. DETErmine the average reading from both transducers and insert them into the following formula: (AVG. OF MASTER) - (AVG.
Chapter 7: System Operation 7.13 DATA FILE UTILIty THe function of this screen is to setup the System to collect and save data to a specified disk drive. 7.13.1 TABLE OF CONTENTs 7.13.1 Table of Contents for Data File Utility screens 7.13.2. Screen Explanation 7.13.3. SCreen OPERATION/PRINT OUT FUNCTIon 7.13.2 SCREEN EXPLANATION 2-1. The DATA FILE Utility screen is used to collect and save data to either a floppy (FDD) disk drive or a hard (HDD) disk drive.
Chapter 7: System Operation FILE START FUNCTION: CYCLE NUMBER: SAMPLING STATUS: MANUAL Data save will initiate after START is chosen from the menu bar AUTOMATIC Data save will initiate with the first fastening cycle. FILE START will revert to MANUAL mode if STOP is input during a run 000000 Cycle Number automatic count-up (Display only) [DATA COMPLETE] (DATA COLLECTING) (Display only - data save status) FIG. 7-13-2 DATA file utility screen 7.13.
Chapter 7: System Operation 3. IF a (save) FILE Name is entered that already exists on the (save) disk, then a "FILE EXISTS" message will appear at the bottom of the screen. If [START] is input, the data will be added to the existing file. If the System has been powered down since the last data save, and the (new) file number/ cycle number combinations are the same as those on the disk, then the disk will be overwritten with the new information. FIG.
Chapter 7: System Operation 3-5a. AFTEr selecting the desired drive, use the alphanumeric pulldown menu to enter the [PATH] and [FILE NAME] information. [PATH] must be either left blank, or set to an existing directory name. When performing data file operations, the System will always reference the root directory first, and then the specified path. After entering the information, select "INPUT END" from the menu and depress the [↵] key.
Chapter 7: System Operation data is collected the [DATA COMPLETE] message will appear in the sampling status window. 3-15a. Data files will be created based upon the following format: "NNNNDD##.
Chapter 7: System Operation 3-4b. the information, select "INPUT END" from the menu and depress the [↵] key. The entered information will appear in the applicable field(s), and the alphanumeric window will close. The following Data file utility screen fields have no affect on the data file contents or format when saving data in Free Format mode: Spindle NumberData will be saved for all spindles, regardless of this setup. Spindle Data Will save in accordance with ALL, regardless of this setup.
Chapter 7: System Operation 3-11b. To print out the Data File Utility screen, move the cursor on the menu bar to [PRINT] and depress the [↵] key.
Chapter 7: System Operation 7.14 PRESET FILE Utility The function of this screen is to perform file maintenance on the preset data configuration for the System. 7.14.1 TABLE OF CONTEnts 7.14.1. TABle of Contents for PRESET FILE Utility screens 7.14.2. SCreen Explanation 7.14.3. SCReen OPERATION/PRINT OUT FUNCTIon 7.14.2 SCREEN EXPLANATION 2-1.
Chapter 7: System Operation 7.14.3 sCREEN OPERation 3-1. To begin presetting for file utilities, insert a formatted disk in the floppy drive as required and depress the [SEL] key. THe cursor will highlight the [ ] FASTENING PARAMETER field. TO activate a file type for a utility function, move the highlighted cursor to the desired item using the [↑] [↓] key and depress the [±] key. AN [*] in the window indicates selection. 3-2.
Chapter 7: System Operation 7.15 FILE UTILITY THE function of this screen is to perform file maintenance on the System's hard disk drive C: (HDD) and floppy disk drive B: (FDD). 7.15.1 TABLE of CONTENTS 7.15.1. TABLe for Contents for FILE UTILITY screens 7.15.2. SCREEN EXPLANATION 7.15.3. SCREEN OPERATION/PRINT FUNCTIOn 7.15.2 SCREEN EXPLANATION 2-1.
Chapter 7: System Operation FIG. 7-15-3-1 FILE UTILITY disk drive selection 3-2. path (directory) and FIle (Tag) Selection 3-2a Select the appropriate disk drive from the available log options. the lower window of the screen will display the file and directory information for that drive. DIrectories are displayed on the screen light blue in color, enclosed in brackets (). 3-2b DEpress the [SEL] key to move the cursor into the lower window of the display screen.
Chapter 7: System Operation 3-3. FILE SPECIFICATION SELEction [FILESPEC] 3-3a [FILESPEC] is used to select the file specification (file extension type) for the selected DRIVE \ PATH. 3-3b MOVE the cursor on the menu bar to [FILESPEC] using the [←] [→] keys [↵] key. the "FILESPEC" pulldown menu will appear. SELect the desired option using the [↑] [↓] keys and the press the [↵] key.
Chapter 7: System Operation FIG. 7-15-3-4b FILE UTILITY FILE DUPLICATIon [COPY] 3-4c. TO input the "DESTINATION DIRECTORY" move the highlighted cursor to the [DESTINATION DIRECTORY] position and depress the [↵] key. THe alphanumeric pulldown menu will appear with a small field and a black flashing cursor. THE alphanumeric menu will show a blue highlighted character. TO input a character into the field, use the [←] [→] key to move to the desired character.
Chapter 7: System Operation 3-5 Directory creation [COPY] 3-5a A destination directory will be created as a result of performing the copy function to a non existent [DESTINATION DIRECTORY]. No file need be specified when the copy function is performed. 3-5b MOVE the cursor on the menu bar to [COPY] using the [←] [→] keys and [↵] key. the "COPY" pulldown menu will appear. SELect the desired [DESTINATION DRIVE] using the [←] [→] keys and the press the [↵] key. press the 3-5c.
Chapter 7: System Operation 3-6 FILE Deletion [DELETE] 3-6a [DELETE] is used to take existing file(s) (individual or tagged) from the selected DRIVE \ PATH \ FILESPEC and delete them. 3-6b MOVE the cursor on the menu bar to [DELETE] using the [←] [→] keys and press the [↵] key. the "DELETE" pulldown menu will appear. SELect either [↵] key. [DELETE] or [CANCEL] as desired and depress the FIG. 7-15-3-6 FILE UTILITY file deletion [delete] 3-6c.
Chapter 7: System Operation (BLANK PAGE) Page 7-93
