INDEX Warranty..........................................................................................................................4 General warning..............................................................................................................6 Trouble-shooting............................................................................................................ 6 Ongoing changes........................................................................................................
English 3
WARRANTY faytech touch displays are produced following the most modern production and test processes. Carefully selected components and accurate production ensure reliable operation and long life. faytech warrants to the original purchaser that each faytech touch display delivered shall be free from defects in material or workmanship at time of shipment, and that each such module delivered will meet the published specifications for a period of 24 months as measured from the date of original shipment.
UNIT OF PRODUCT OR SERVICE FURNISHED OR TO BE FURNISHED AS THE CASE MAY BE WHICH IS THE SUBJECT OF CLAIM OR DISPUTE. IN NO EVENT SHALL SELLER BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES. LIABILITY TO THIRD PARTIES, FOR BODILY INJURY INCLUDING DEATH, RESULTING FROM SELLER'S PERFORMANCE SHALL BE DETERMINED IN ACCORDANCE WITH APPLICABLE LAW AND THE TOTAL LIABILITY LIMITATION STATED ABOVE SHALL NOT BE CONSTRUED AS A LIMITATION ON SELLER FOR DAMAGES FOR ANY SUCH BODILY INJURY, INCLUDING DEATH.
Any warranty claim must be accompanied by proof of purchase (receipt or invoice). improvements. If you have any questions or suggestions, please contact our support team or visit our website at www.faytech.com GENERAL WARNING Avoid all contact with dirt, oil, dust or water. Never open the unit. Do not drop the unit. If you notice a burning smell or hear the device making unusual sounds, please disconnect it immediately from the power source.
COMPON ENTS 01. 02. 03. 04. 05. 06. 01. PWR: turn the display on or off 02. MENU: open the OSD menu –orconfirm selection in the OSD menu 03.
07. 08. 09. 10. 11. 07. Power 08. Audio-In 12. 09. VGA 10. DVI 11. HDMI 12. 12V power supply 14. 13. 13. VGA Cable 14.
DISPLAY CONNECTION USING THE TOUCH FUNCTION To operate your faytech display properly, there must be at least one signal source and a power source connected. To use the touch function please connect the USB cable to your PC. Connect the USB cable to the USB port on your PC (after you have been asked within the software installation process). TO CO NNECT THE SIGNAL SOURCE you have the following options: On a PC: Connect the VGA cable from the faytech monitor to the VGA output of your PC graphics card.
Auto calibration: The display is automatically adjusted to the current resolution of your graphics card. If you are not satisfied with the auto setting, you can optimize it manually. Auto color: This function will optimize the color of the faytech displays. You can always change the color of the display manually. Change visual distortion when viewing the screen from different angles. Use +/ to find the best display effect.
Menu V. Position: To move the position of the menu up (-) or down (+). Menu Timeout: Determines how many seconds the OSD menu is displayed before it is automatically switched off, if there are no more operations. You can also select “off” to remove the OSD menu from the screen. Transparency: You can choose various levels of transparency for the OSD-Menu. Exit: Return to the main menu or submenu. Settings Reset: This option will return the display back to the factory settings.
warnings may be given depending on installed security programs. Always click the button to continue the operation. To complete the installation with all default options, click “Next” on each of the following dialog boxes. You can cancel at any time. To switch back to a previous step, click the “
If you plan to use multiple monitors, please choose this box. (See “Setting up the faytech Touch software”.) SETTING UP THE FAYTECH TOUCH SOFTWARE 8."Choose Destination Location": Accept the default destination or choose your own then press "Next". Start the administration program by going to “Start - Programs -TouchKit – Configure Utility”. (If you accepted all the defaults the program may be at “Start – Programs – Accessories – Touchkit – Configure Utility”.
The same applies to Double Click Area. If you choose Smaller <<, your taps must be in a relatively small area in order for a double click to be recognized. >> Larger enables you to make a successful double- click within a larger area. Click on touch without moving cursor: The first touch point generates a click. The cursor follows the finger / pen movement. For a better understanding of this setting, try it with the Draw Test application under the Tools tab.
Enable Cursor Stablization: A software filter exists inside the driver to filter some noise to stabilize and smooth the touch points. When activated, the user will experience a more stable cursor. You can adjust the parameter for the Constant Touch Area function. This is a criterion to judge if the most recent touched point is the same as the previously touched point.
screen will be shown in the Linearity curve window. The Draw Test function is used for accuracy and performance checking. Press this button and a new pop up window will be popped up on the monitor . Touch or drag your touch pen or finger on this grid to gauge the effectiveness of the settings and calibrations that you have made. If you are using your finger, you may have to press firmly to draw continuous lines. Press the Clear button to clear the window. Press the Quit button to terminate this draw test.
If the function "The touch sensor is automatically connected to the main system" is activated, the program automatically puts the touch function on the primary monitor, if only one monitor is connected. The Operation mode settings allow you to set the size of the touch area on your faytech touch-screen. E.g. if you select the "right screen“, after a new calibration only the right side of the monitor will work as a touch area.
On the context menu, if you select the option Display Button, you will see a mouse animation displayed in the lower right half of the screen. The red mark indicates which mouse button will be simulated the next time you touch the screen. By clicking on the left or right pointer of the animation you change the behavior of the touch panel accordingly.
TIPP IT IS BEST TO USE THE 15”DISPLAY AT A RESOLUTION OF 1024X768, THE 17” DISPLAY AT 1280X1024, THE 19" DISPLAY AT 1440X900, THE 22" AT 1680X1050 AT 60HZ. Power supply error: If the display has no signal input, there might be an error with the power supply. First please check the connection with another power supply before you return the display. We're happy to exchange the defective power supply if necessary.
TECHNICAL DATA Changes in the sense of technical progress reserved. 26 INCH VANDAL PROOF MONITOR Display case (cm): 37.00 x 28.70 x 5.67 Screen diagonal (Inch/cm): 15/38,1 Display (cm): 30.40 x 22.80 Standard stand, VESA-100 on the back / VESA-400 on the Mounting: back Gross weight (inclusive cartonage, kg): 5 Net display weight (kg): 3 Aspect ratio: 4:3 Physical resolution: 1024 x 768 Maximum showable resolution: 1920 x 1200 Colours displayed: 16.
Input force (g): 20 ~ 150 Connectors, video: 1x VGA, 1 x DVI-D Connectors, audio: 1x Audio-In Power-supply (included in delivery): 230V, 12V OSD-Menu, Speaker, Touchpen, Driver-CD, Short Additional features Installation Manual Dot Clock： 45~82MHZ Analog Scanning Frequency (H, V): 37.9~74.
CONTACT Contact, RMA service (in English): Support Number: +1 720 251 4158 Global Support: +86 755 89580612 Support E-Mai: support@faytech.com Homepage: www.faytech.com U.S.A. Warehouse: 121 Varick Street, 3rd Floor, New York, NY 10013 Tel: +1 720 251 4158 RMA Service: If you think your faytech product has a defect please always contact us directly. Our trained after sales service specialists can help you resolve your problems.
