AudioCodes Mediant 1000 Configuration Guide © 2010 FaxBack, Inc. All Rights Reserved. NET SatisFAXtion and other FaxBack products, brands and trademarks are property of FaxBack, Inc. Other products, brands and trademarks are property of their respective owners/companies.
AudioCodes Mediant 1000 Configuration Guide — Page 2 Contents Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Connecting the Mediant 1000 to the Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Accessing the Media Gateway via Browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Assign Static IP Addresses .
AudioCodes Mediant 1000 Configuration Guide — Page 3 Before You Begin • • • • • • • There are a few things you will need before you get started installing your new Mediant 1000. One Ethernet patch cable. A 19” rack or other place to mount the appliance. Rails may be needed depending on rack hardware. One static IP address on the same subnet as your fax server. Sufficient telephone and/or ISDN PRI cables to connect the telephony modules.
AudioCodes Mediant 1000 Configuration Guide — Page 4 Initial Media Gateway Configuration This document only covers basic configuration. For more information regarding these options, and more advanced configuration, please refer to the AudioCodes Mediant 1000 manual which can be found on the AudioCodes documentation CD. IMPORTANT: Changes you make will be lost when the device reboots, unless you click the Burn button at the top of the page. Once you are done making changes, be sure to click “Burn”.
AudioCodes Mediant 1000 Configuration Guide — Page 5 Trunk Groups Configuration > Protocol Configuration > Trunk/IP Group > Trunk Group The following screen shot is an example only, your hardware will need a different configuration. Read below for details. See also “Media Gateway Configuration Examples” for sample configurations. The configuration instructions that follow will use Trunk Group ID 1 for all “PSTN” ports. That is, all ports capable of calling other numbers.
AudioCodes Mediant 1000 Configuration Guide — Page 6 Configuration > Protocol Configuration > Trunk/IP Group > Trunk Group Settings Create two trunk groups: Trunk Group ID 1 Channel Select Mode Cyclic Ascending Registration Mode (blank) Trunk Group ID 2 Channel Select Mode By Dest Phone Number Registration Mode (blank) Click “Submit” when you are done. Click “Burn” at the top of the page.
AudioCodes Mediant 1000 Configuration Guide — Page 7 Routing Table – Tel to IP Configuration > Protocol Configuration > Routing Tables > Tel to IP Routing This page allows you to route calls from the telephony interfaces to the IP address of the fax server. The following screen shot is an example only, your hardware will need a different configuration. Read below for details. See also “Media Gateway Configuration Examples” for sample configurations.
AudioCodes Mediant 1000 Configuration Guide — Page 8 Routing Table – IP to Trunk Group Configuration > Protocol Configuration > Routing Tables > IP to Trunk Group Routing This page allows you to route calls from IP addresses to the telephony interfaces on the device. The following screen shot is an example only, your hardware will need a different configuration. Read below for details. Create one entry: Dest.
AudioCodes Mediant 1000 Configuration Guide — Page 9 PRI or T1 Configuration Configuration > PSTN Settings > Trunk Settings Configure each trunk to match the PRI configuration specified by your service provider. Click “Submit” when you are done. Click “Burn” at the top of the page.
AudioCodes Mediant 1000 Configuration Guide — Page 10 FXO Configuration Configuration > Protocol Configuration > Endpoint Settings > Automatic Dialing NOTE: Do not configure automatic dialing for FXS ports; this will prevent you from faxing to any number but the “Destination Phone Number.” If you are receiving DTMF tones from a PBX on the FXO lines, it is not strictly necessary to configure automatic dialing.
AudioCodes Mediant 1000 Configuration Guide — Page 11 Media Gateway Configuration Examples Only a PRI Module This example Mediant has only a single PRI module installed. Trunk Groups Group Index Module From Trunk To Trunk Channels Phone Number Trunk Group ID 1 Module 1 PRI 1 1 1-23 1 1000 Tel to IP Routing Dest Phone Prefix Source Phone Prefix -> Dest IP Address 1 * * The “Dest IP Address” above is the IP Address of the NET SatisFAXtion Fax Server.
AudioCodes Mediant 1000 Configuration Guide — Page 12 Mixed PRI and FXS Modules This example Mediant has one PRI module and two FXS modules (8 FXS ports) installed.
AudioCodes Mediant 1000 Configuration Guide — Page 13 Mixed FXO and FXS Modules This example Mediant has two FXO modules (8 FXO ports) and two FXS modules (8 FXS ports) installed.
