POCKEY 2IN1 GAME TABLE (800) 225-7593 X113 UPC Code 7-19265-53568-3
A copy of your receipt will be needed to activate your warranty (see page 13).
1-(800) 225-7593 X113 2
Please see page 13.
4
Table Top Order No. 2-200 Pedestal Order No. 2-201 End Rail Order No. 2-8 Side Rail Order No. 2-6 Puck Catcher Order No. 2-202 4 Hex Head Bolt 1/4”*2” Lg. Hex Head Bolt 1/4”*3” Lg. 16 2-31 6 3 Are Preassembled 3/4” Washer Order No. 2-16 2 Are Preassembled 3/4” Hex Nut Order No. 2-17 Order No.
64-1010 (PRE-Assembled) 2 Cues Rack Order No. 2-204 2 Puck Holder Order No. 2-205 (PRE-Assembled) 18 2 Allen Key Bolt 3/16”*1” Lg. Order No. 2-203 2-206 32 Slide Scorer 2-208 Corner 2-207 30 W/P4*1-1/4” Screw 31 4 4 F4*1” Screw 2-209 6 1 Allen Key Order No.
Pockey 2 in 1 Game Table Item 64-1010 Assembly Remove all components from the carton NOTE: Parts are packed inside the table top (#1). Remove the pool table surface, inside the table top you will find all the parts needed to assemble your table .When all the parts are out of the table top, replace the pool table surface. Reattach the pool table surface by repcaing the screws(#28). #1 #28 Step 1. Assemble the pedestal . • Carefully remove two (#2) pedestals and four levelers (#22) from the package.
12 #11 #12 #12 #11 #12 #12 #11 12 11 12 4. Tighten all bolts using wrench (#24).
The end of the table top with the power cord has the three 3/4” washers (#14) and two 3/4” hex nuts (#15) pre assembled on the power cord. 14 15 14 Place another washer #14 and thread a nut #15 onto the support axle.
Step 6. Attach the puck catchers and accessory Holder. • Align the puck catcher (#6) with the predrilled holes on each end of the playing table. Secure to pedestal with round head screws (#13). Run the power cord through the puck catcher. • Align the accessory holder (#26) with the pedrilled holes on each end of the playing table. Secure to pedestal with screws (#13). • Attach both Slide Scorers (#31) to the edges of the Hockey Cabinet using four Screws (#32).
64-1010 #1 Plug in to test. Clean the surface by spraying a ray (do not spray directly onto the surface) with a furniture polish (like pledge) and buffing the surface of the table and also buffing the puck. This will provide a bit more “float” which. may alleviate getting hung up in the “dead” areas.
64-1010 12
64-1010 14 13
64-1010 Game Table 14
15
Parts Re-Order Form Traditional Pockey ® Table, Models 64-1010 Part # 2-200 2-201 2-6 2-8 2-9 2-202 2-203 2-12 2-13 2-14 2-15 2-16 2-17 2-18 2-19 2-20 Description Unit Price US$ Table Top Pedestal Side Rail End Rail Table Lock Puck Catcher 300.00ea. 50.00ea. 25.00ea. 25.00ea. 10.00ea. 10.00ea. Allen Key Bolt 3/16”*1” Lg .25ea. 1/4” Barrel Nut .25ea. Hex Head Bolt 1/4”*2” Lg 2.00ea. Hex Head Bolt 1/4”*3” Lg 2.00ea. 1/4” Washer 3/4” Washer 3/4” Hex Nut Goalie .25ea. .20ea. .20ea. 6.00ea. Felt Pad 1.
