Pyramid 3D PRINTER Quick Installation Guide
Contents 1. 2. 3. 4. 5. 6. 7. 8. 9.
Machine parameters Printing Size(mm) 300*300*400 Molding Tech FDM Slice Software CURA /Simplify3D/ Repetier-Host ect Power Supply AC :115-240 V DC:24V 15A Nozzle Number 1 Total Power 360W Slice Thickness 0.1-0.4mm Bed Temp ≤ 110℃ Precision ±0.1mm Nozzle Temp ≤ 260℃ Nozzle Diameter 0.4mm.Support 0.2/0.3/0.6/0.
Extruder Extrusion Support frame X-Motor Extruder Screw rod Coupling Heat bed Z- limit switch Touch screen Control box Z- motor Y-motor Bed leveing nut 2 Power
Printer base*1 M4×20 *4 X belt bearing*1 2040 aluminum profile*2 M4×16 *6 Belt *1 Z-motor *2 X-axis left part*1 Extruder part *1 Coupling *2 X-axis right part*1 X end stop*1 3 M3×6 *2 Screw rod fixing block*2 M5×25 *8 Screw rod *2 2020 aluminum profile*2
Pull rod-285mm*4 M5×10 *4 Live bolts M6×35 *4 M5×8 *8 M5 T Nut *10 Connetcor A *2 M6 Nut *4 Screws M6×40 *2 Connetcor B *2 4
Preparation list 1. Inshtall the 2040 aluminum profile on the printer base,with 2 pcs M4×20 each side. 2.
X-axis left part*1 M4×16 *2 Step1 Install X-axis left part with 2 pcs M4×16 Extruder part *1 Belt *1 Step2 Install Extruder part with the belt pass through the X-axis M4×16 *2 X-axis right part*1 Step3 Install X-axis right part with 2 pcs M4×16 6 X belt bearing*1 M4×16 *2 Step4 Install X belt bearing with 2 pcs M4×16 X end stop*1 M3×6 *2 Step5 Install X end stop with 2 pcs M3×6
Preparation list Step 2: Install the Gantry top beam with 2 pcs M5×25 each side M5×25 *4 Step 1: put the X-axis part pass through the 2040 pillar 7
Preparation list Step 2：Install the screw rod fixing block Step 1：Install the Screw rod and tighten the Couplings 8
Part 5：Install support rod Preparation list Connetcor A *1 M5 T Nut *2 Live bolts M6×35 *1 M6 Nut *2 M5×8 *2 M5×10 *1 Pull rod-285mm*2 Screws M6×40 *2 M5×10 *1 M5×8 *2 Connetcor B *1 M6 Nut *2 9
E-motor X-motor Z-limit Z-limit Z-motor Z-motor Select voltage before starting up 10
11
Level the heated bed 1. Auto Home All Disable xy 2. Test with A4 paper, adjust the nuts under the platform up and down, to make the nozzle just presses the A4 paper, and ensure that the four corners are the same distance.
Too close: The short distance may lead to abnormal discharge or even damage caused by plugging the nozzle Normal: The correct distance will help you to complete the printing work better and more economically Too far: Too far distance will cause printing materials to be unable to attach to the hot bed, so that they cannot be printed normally 13
1.
2.
1.
2.
3. Put the TF card to the printer, Select “Printing”----Select your file 4.
Dear customers: 1. In order to ensure the quality of products, we will carry out printing test for each printer in the factory. If you find that the nozzle has slight traces of use, this is left by the printing test. We try to clean it up as much as possible, but please don't mind. 2. The factory test voltage is 220V. When installing, please select 110V or 220V according to your local power supply to ensure the printer can work normally.
20
Tips: More informations on the TF card email: service@fasttobuy.com Amazon: fasttobuyli@gmail.com Amazon store: www.amazon.
