Specification

ICC-ES Evaluation Reports are not to be construed as representing aesthetics or any other attributes not specifically addressed, nor are they to be construed
as an endorsement of the subject of the report or a recommendation for its use. There is no warranty by ICC Evaluation Service, LLC, express or implied, as
to any finding or other matter in this report, or as to any product covered by the report.
Copyright © 2014 Page 1 of 8
1000
ICC-ES Evaluation Report
ESR-1078
Reissued January 1, 2014
This report is subject to renewal January 1, 2015.
www.icc-es.org | [phone] | [phone] A Subsidiary of the International Code Council
®
DIVISION: 06 00 00—WOOD, PLASTICS AND
COMPOSITES
Section: 06 05 23—Wood, Plastic, and Composite
Fastenings
REPORT HOLDER:
OMG, INC.
153 BOWLES ROAD
AGAWAM, MASSACHUSETTS 01001-5008
[phone]
www.olyfast.com
www.fastenmaster.com
[e-mail]
ADDITIONAL LISTEE:
MITEK INDUSTRIES, INC.
14515 NORTH OUTER FORTY, SUITE 300
CHESTERFIELD, MISSOURI 63017
[phone]
www.mii.com
EVALUATION SUBJECT:
FASTENMASTER
®
LOK SERIES STRUCTURAL WOOD
SCREWS
1.0 EVALUATION SCOPE
Compliance with the following codes:
 2012, 2009 and 2006 International Building Code
®
(IBC)
 2012, 2009 and 2006 International Residential Code
®
(IRC)
Properties evaluated:
 Structural
 Corrosion resistance
2.0 USES
The FastenMaster LOK Series fasteners described in this
report are alternate dowel-type threaded fasteners used for
wood-to-wood connections.
The FastenMaster LOK Series fasteners having a
proprietary corrosion-resistant coating with a lubricious
clear top coat may be used where fasteners are required to
exhibit corrosion resistance when exposed to adverse
environmental conditions and/or in preservative-treated
wood (subject to the limitations of Section 5.2), and are
alternates to hot-dip-zinc galvanized fasteners with a
coating weight in compliance with ASTM A153, Class D.
The fasteners have been evaluated for use with wood
chemically treated with waterborne alkaline copper
quaternary, type D (ACQ-D).
3.0 DESCRIPTION
3.1 General:
The LOK Series fasteners described in this report are
manufactured using a standard cold-forming process and
are heat-treated. These fasteners depart from ANSI
B18.2.1 and B18.6.1 in thread design, exceed the bending
yield strengths documented in Table 5 of American Forest
& Paper Association (AF&PA) Technical Report 12, and
are not installed with lead holes in accordance with the
National Design Specification for Wood Construction
(NDS). The LOK Series fasteners recognized in this report
are described in Sections 3.1.1 through 3.1.5.
3.1.1 OlyLog and TimberLOK Fasteners: The OlyLog
and TimberLOK fasteners have a
5
/
16
-inch (7.9 mm) hex-
head, rolled threads and a gimlet point. They have a
proprietary corrosion-resistant coating with a lubricious
clear top coat. See Table 1A for fastener dimensions and a
diagram.
3.1.2 HeadLOK Fasteners: The HeadLOK fasteners
have a proprietary #3 Spider-drive head, rolled threads and
a gimlet point. They have a proprietary corrosion-resistant
coating with a lubricious clear top coat. See Table 1B for
fastener dimensions and a diagram.
3.1.3 LedgerLOK and LogHog Fasteners: The
LedgerLOK and LogHog fasteners have a
5
/
16
-inch
(7.9 mm) hex-head with integral washer, rolled threads and
a gimlet point. They have a proprietary corrosion-resistant
coating with a lubricious clear top coat. See Table 1C for
fastener dimensions and a diagram.
3.1.4 TrussLOK and TrussLOK-Z Fasteners: The
TrussLOK and TrussLOK-Z fasteners have a
3
/
8
-inch
(9.5 mm) hex-head, rolled threads and proprietary cutting
points. They have a proprietary corrosion-resistant coating
with a lubricious clear top coat. See Tables 1D and 1E for
fastener dimensions and a diagram.
3.1.5 ThruLOK Fasteners: The ThruLOK fasteners have
a
5
/
16
-inch (7.9 mm) hex-head, rolled threads and a
proprietary cutting point. The fasteners are coated with
mechanically applied zinc in accordance with ASTM B695,
Type I, Class 55. They are supplied with the ThruLOK
washer and nut. See Table 1F for fastener dimensions and
a diagram.
3.2 Materials:
The fasteners are made of carbon steel grade 1022 or
10B21 wire, conforming to the report holder’s material