© Fast & FLuid Management, TmHC manual FAST & FLUID MANAGEMENT TMHC ENGLISH p1
© Fast & FLuid Management, TmHC manual Table of Contents TmHC Manual Safety instructions Installation Maintenance Service Contributing to the Protection of the Environment p2 3 3 4 9 10 11
© Fast & FLuid Management, TmHC manual TmHC Manual Safety instructions General safety instructions Attention! Before installing the equipment and setting it in operation, please read this manual carefully. This is safer both for yourself and the machine. The manufacturer accepts no liability if the instructions below are not followed: 1. 2. 3. 4. 5. 6. 7. If the TMHC has been damaged (e.g. during transport), do not attempt to set it in operation.
© Fast & FLuid Management, TmHC manual Installation Attention! Please do not switch on the machine before removing the transport protection (roll of packing foam) as explained in step 2 Step 1 - Detach the TMHC from its transport skid > Place the skid close to the end destination and remove its plastic wrapping. Unscrew all four transport brackets. > The brackets can be removed at the top of the aluminum corner beams.
© Fast & FLuid Management, TmHC manual Step 2 - Remove transport protection > Unlock the front door, a triangular key is supplied with the machine. > Pull out the roll of foam. Close the top lid first, then close (and lock) the door. Step 3 - Hook up TMHC to power outlet > Connect the power cable to a wall socket. > Switch on the TMHC. After the board initialisation (appr 10 seconds), the screen will show your logo.
© Fast & FLuid Management, TmHC manual Step 4 - Place cassettes for first use > Press any key to enter the main menu (the machine will intialise once more), enter the maintenance menu. > Enter the service menu and press the ‘>’-key. > Choose the ‘button control’ function to allow manual positioning of the table. Enter your Personal Identification Number (pilot machines: 0252) and press the ‘>’-key. > Unlock and open door and press the ‘>’-key.
© Fast & FLuid Management, TmHC manual > Lower the handle to its bottom position. > Press the cassette down to the snap. The handle will automatically rise bac k up > Hold key in front of sensors on inside of the door to move table to next position. Ensure the connection by pressing the handle firmly against the pump. > Repeat cassette placement procedure for all positions. p7 Close the top lid first, then close (and lock) the door.
© Fast & FLuid Management, TmHC manual Step 5 - Prime (=flush) for first use > Return to the Service Menu and choose the ‘maximize fill levels’ to reset the pouch level parameters. > Place an empty container and choose the ‘clean all’ function flush air from the system. This will take a few minutes. Viscose materials (yoghurt-like) may need upto 5 strokes to fully purge. p8 For highly viscose products requiring many prime strokes, it may be practical to flush these seperately. Choose ‘clean single’.
© Fast & FLuid Management, TmHC manual Maintenance Daily maintenance > Open the TMHC door and remove the steel drip tray. Clean with water if soiled. > Pull out the brush tray and rinse with water. Refill with water, approximately 30ml. p9 If severely soiled, the brush can be removed from the tray for cleaning.
© Fast & FLuid Management, TmHC manual Service When (re)placing the front panel on the door’s framework, make sure the door is closed and locked. This guarantees the door’s relatively flexible framework is ‘stiffened’ in the correct shape and position. Pump & box holder module replacement > Choose: Maintenance > Go To > Position and enter desired value +6 to have the defect module position to the left-hand side of the TMHC. > Remove the left-hand side panel by unscrewing its four fasteners.
© Fast & FLuid Management, TmHC manual Contributing to the Protection of the Environment Packaging Material The packaging protects the machine against damage during transport. The packaging m aterial was chosen based on its limited impact on the environment and its inherent possibilities for waste-disposal. The reuse of packaging material saves raw materials and produces less waste material. Generally speaking, your supplier will take the packaging off your hands.
© Fast & FLuid Management, TmHC manual © Fast & FLuid Management, 2005 w w w .Fast-Fluid.
