Manual Harbil HA450 / Harbil HA650 V. 1.0 Fast & Fluid Management B. V. PO Box 220 2170 AE Sassenheim The Netherlands www.fast-fluid.
© Fast & Fluid Management B.V. This manual or parts thereof may not be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, nor otherwise, without the prior written permission of Fast & Fluid Management B.V. This manual could contain technical inaccuracies or typographical errors. Fast & Fluid Management B.V.
Table of Contents HA450 / HA650 V. 1.0 Table of Contents 1 2 3 4 About this manual......................................................................................................... 5 1.1 How to work with the manual .......................................................................................... 5 1.2 Record of changes ......................................................................................................... 5 Safety .................................................
Table of Contents 5 6 HA450 / HA650 V. 1.0 4.2 Put the machine in position .......................................................................................... 23 4.2.1 Move the machine to the final location, with a ramp (optional) .......................... 23 4.2.2 Place the machine on the final location.............................................................. 23 4.2.3 Place the step..................................................................................................... 24 4.
About this manual 1 HA450 / HA650 About this manual The manual shows the information necessary to: - install - operate - perform basic maintenance - correct small problems. The HA450, the HA650 and all their versions are referred to in the manual as the ’machine’. This manual contains the original instructions. The original language of the manual is English. 1.1 How to work with the manual 1 2 3 1.2 Familiarize yourself with the structure and content.
About this manual HA450 / HA650 6 V. 1.
Safety 2 HA450 / HA650 V. 1.0 Safety WARNING Read the manual before you install or use the machine. Failure to do so can result in personal injury, death or property damage. 2.1 Intended use The machine is designed to dispense colorants into a can. Any other use of the machine is strictly forbidden. 2.2 Liability Our machines and accessories are fully compliant with the CE regulations. Any modification can result in not fulfilling the CE safety requirements and is therefore not allowed.
Safety 2.5 HA450 / HA650 V. 1.0 Safety symbols on the machine /i Rotating parts hazard Pinch hazard hand Central earting point Pinch hazard foot Read the manual Caution Electrical hazard Can table switch up-down Instruction 2.6 Safety symbols in the manual /i WARNING Can cause personal injury. WARNING Pinch hazard for your foot. CAUTION Can cause damage to the machine. Note Shows further information.
Safety 2.7 HA450 / HA650 Disposal of the machine 1. Sort the machine, the accessories and the packaging for environmentally friendly recycling. 2. Do not dispose of the machine into domestic waste. Dispose of the machine according to local regulations. 3. Dispose of the canisters as chemical waste, according to the local regulations. 9 V. 1.
Safety HA450 / HA650 10 V. 1.
Operator manual HA450 / HA650 3 Operator manual 3.1 Description 3.1.1 Overview of the machine V. 1.
Operator manual 3.1.2 HA450 / HA650 V. 1.
Operator manual 3.1.3 HA450 / HA650 Overview of the machine (back) A B C D A: B: C: D: Lock Type plate Net entry Wall socket 13 V. 1.
Operator manual 3.1.4 HA450 / HA650 Type plate: serial number Fast & Fluid Management B.V. IDEX Dispensing P.O. Box 220 2170 AE Sassenheim The Netherlands THE TINTING COMPANY www.fast-fluid.com Model XXXXX-XX (Xxxxxxx) Prod. Week XX-XXXX Serial No: XXXXXXXXX-XXXXXX 3.1.5 Type plate: details Fast & Fluid Management B.V. IDEX Dispensing P.O. Box 220 2170 AE Sassenheim The Netherlands THE TINTING COMPANY www.fast-fluid.com XXX V~ XX/XX Hz XXX W Model XXX XX-XXX Serial no. XXXXXXXXX-XXXXXX Prod.
Operator manual 3.2 HA450 / HA650 V. 1.0 Operation WARNING Only push the emergency stop switch in the case of a safety emergency. Make sure that the problem is solved before you reset the emergency stop switch. When you reset the emergency stop switch, the machine restarts automatically. When the machine is operational, you hear ’beep beep’. CAUTION Do not remove the power from the machine. The machine must stir the colorants periodically. Note The computer switch only turns the computer on and off.
Operator manual 3.2.3 HA450 / HA650 V. 1.0 Move up the can table 1. Push and hold the upper part of the can table switch (A). The can table (B) moves up and stops when the can is in front of the can sensor (C). 2. After the can table stops, release the can table switch. A C B 3.2.4 Move down the can table 1. Push and hold the lower part of the can table switch (A). The can table (B) moves down. 2. When you can remove the can, release the can table switch.
Operator manual 3.3.2 HA450 / HA650 Cleaning of the brush container: daily CAUTION If you do not clean these items daily, severe pollution will occur. Open the side door 1. Put the key in the key lock and turn it counter clockwise. 2. Open the side door. Remove the brush container 1. Remove the brush container. Use the handle. 17 V. 1.
Operator manual HA450 / HA650 Remove the brush 1. Remove the brush from the brush container. Clean the brush container 1. Remove the liquid from the brush container. For the disposal of the liquid, follow the local regulations. Fill the brush container 1. Fill the brush container, with the liquid that your paint supplier indicates. The level of the liquid must be between the “MIN” and “MAX” mark. 2. Place the brush container back in its position. 3. Close the side door .
Operator manual 3.3.3 HA450 / HA650 V. 1.0 Refilling of a canister CAUTION Make sure that the colorant level in the canister is correct. If a canister is empty, this can cause an inaccurate dispensing and/or a recipe fault. Note The software checks the level of colorant in each canister. The software on the machine shows when you need to refill a canister. 1. 2. 3. 4. In the software, activate the fill canister option. Open the top cover (A). Remove the lid of the canister (B). Add the colorant (C).
Operator manual HA450 / HA650 20 V. 1.
Installation 4 Installation 4.1 Unpack the machine 4.1.1 Remove the cardboard HA450 / HA650 V. 1.0 1. Remove the cardboard (A) and the plastic from the outside of the machine. A 4.1.2 Remove the transport brackets at the front 1. Lift the cover (A). 2. Unscrew the transport bracket (B) and remove it.
Installation 4.1.3 HA450 / HA650 V. 1.0 Remove the transport brackets at the rear 1. Open the back cover (A). Use the key (B). 2. Remove the back cover. Let the back cover move towards you. Then lift the cover. 3. Unscrew the transport brackets (C) and (D) and remove them. B A D 10mm C 4.1.4 Remove the wooden beams 1. Remove the wooden beams. 4.1.5 Remove the plastic protection on the canisters 1. Remove the blue tape and open the top cover. 2. Remove the plastic protection.
Installation 4.1.6 HA450 / HA650 V. 1.0 Remove the plastic protection from the switchplate 1. Open the side door. See § 3.3.2. 2. Remove the plastic protection from the switchplate. 4.2 Put the machine in position 4.2.1 Move the machine to the final location, with a ramp (optional) 1. 2. 3. 4. Place the ramp (A). Move the machine from the pallet on to the ground. Move the machine to the final location. Connect the power cable to the net entry. Do not connect the power cable to the wall socket.
Installation 4.2.3 HA450 / HA650 Place the step 1. Place the step from the left side under the can table. 4.2.4 Turn the step 1. Turn the step to the front. 4.3 Install the computer 4.3.1 Open the back cover 1. Open the back cover. See § 4.1.3 2. Remove the back cover. 24 V. 1.
Installation 4.3.2 HA450 / HA650 V. 1.0 Install the computer Note Usually, the computer already has the correct software and drivers installed. If not, refer to the instructions in the installation manuals of your software provider. 1. Put the computer in the machine. 2. Connect the power cables of the computer and the screen to the 4-way socket (A). 3. Connect an USB cable between the computer and the power board (B). 4. Connect the keyboard, the mouse and the screen to the computer. 4.
Installation HA450 / HA650 26 V. 1.
Troubleshooting 5 HA450 / HA650 V. 1.0 Troubleshooting Note For all error messages on the computer: see the help topic in the dispense software. 5.1 Contact service 1. Find the type plate on the rear of the machine. See § 3.1.5. 2. Take a note of the model number and the serial number of the machine. 3. Contact your supplier or manufacturer. See www.fast-fluid.com. 5.2 Sound signals Sound signal Possible cause xxx xxx S-O-S signal during stirring.
Troubleshooting 5.3 HA450 / HA650 V. 1.0 Troubleshooting guide Problem Possible cause Possible solution Main power supply is present but the machine does not work. Emergency stop switch is active. Reset the emergency stop switch. When the problem persists, contact service. See § 5.1. A fuse is broken. Contact service. See § 5.1. Display shows E01 Machine not initialized. Restart machine. When the problem persists, contact service. See § 5.1. Display shows E02 Front door opened.
Technical data 6 Technical data 6.1 General specifications HA450 / HA650 V. 1.0 /i Parameter Specification Number of canisters HA 450 HA 600 32 max 36 max Dispensing Sequential Pump type Harbil piston pump Cleaning system Automatic Materials used are suitable for Canister sizes [L] Water-, universal- and solvent based colorants 2, 3, 6, 10 [L] Pump Capacity 6.2 2, 3, 6, 10, 20 [L] 1, 2, 5, 10 ounce Maximal Can Height 42 [cm] (Low), 46 [cm] (std.
Technical data 6.3 HA450 / HA650 V. 1.0 Ambient conditions /i 6.4 Parameter Specification Temperature [°C] +5 to +40 [°C] Altitude above sea level [m], operational -10 to 2000 [m] Altitude above sea level [m], out of operation -10 to 12000 [m] Relative humidity, without condensation [%] 90% RH Noise level /i Parameter Specification Maximum noise level [dB(A)] 6.
Technical data 6.7 HA450 / HA650 V. 1.0 Pump Parameter Specification /i Pump Parameter Specification 1 [oz] 2 [oz] 5 [oz] 10 [oz] Resolution [ml/step] 0,002 0,004 0,010 0,020 Max Flow speed 1, 2, 5, 10 oz pumps 1 [L/min] 0,2 0,4 0,8-1 1,5-2 Min Dispense in [ml] 0,05 0,08 0,15 0,30 Nozzle diameter Small-Large [mm] 2&4 2&4 2&4 6 1.
Technical data 6.8 HA450 / HA650 Wiring diagram HA450 / HA650 32 V. 1.
