Instructions manual for the Dispenser Type : Automatic small HA-s/medium HA-m mediumII HA-mII/large HA-l Illustrated model: HA-24m 1860331-eng
EU-declaration of conformity 1 We, Fluid Management Europe B.V.
Table of contents 2 1. General page 3 2. Guarantee conditions page 4 3. Safety instructions and warnings page 5 4. Positioning / Installing the machine page 6 4.1 4.2 4.3 5. 6. 7. 8. Conditions for correct positioning Installing the machine 4.2.1 Preparation 4.2.2 Removing the pallet Mounting the monitor stand and installing the computer system 4.3.1 Mounting the monitor stand (HA-s/m/l) 4.3.2 Mounting the monitor stand (HA-mII) 4.3.
1 General 3 By selecting a Fluid Management Color Dispenser you have opted for a product which is the result of intensive research in the field of high-tech color dispensing equipment. Top quality components, craftsmanship and modern ergonomic design all serve to guarantee a long service life and a high degree of user friendliness.
2 Guarantee conditions 4 In these guarantee conditions, 'FM' is understood to mean Fluid Management. The guarantee conditions incorporated into FM's general conditions of sale are summarized as follows (for free general conditions you can apply to FM): 1. FM guarantees the proper operation of any goods which it supplies, for a period of one year, except where a breakdown is the result of normal wear and tear.
3 Safety instructions and warnings 5 Before installing the equipment and setting it in operation, read the instructions for use carefully. This is safer for you and it prevents needless damage to the machine. The manufacturer accepts no liability if the instructions below are not followed: • If a machine has been damaged (during transport, for example), do not attempt to set it in operation. When in doubt, first contact either the Service department (see section 6.4) or your supplier.
4 Positioning / Installing the machine 4.1 6 Conditions for correct positioning Make sure that the following requirements are met when positioning the machine. • • • • Place the machine on a stable, flat surface, and make sure that it is level. Any dry, well ventilated place is suitable. The machine should preferably not be placed in the sun or near a radiator or other source of heat, since this can cause the pastes to dry out.
4 Positioning / Installing the machine 7 4.2.2 Removing the pallet Carefully manoeuvre the machine backwards, with 2 people behind and 1 person in front of the machine (see figure 2) and lower the machine gently on to its rear wheels, so that the situation in figure 3 is reached. Remaining in the same formation, tip the machine backwards until it is clear of the pallet, and the pallet can be pushed out of the way.
4 Positioning / Installing the machine 8 4.3.2 Mounting of monitorstand (HA-mII) The monitorstand can be mounted on either side of the machine. It is normally mounted on the right hand side. To mount it on the left hand side the screenbracket behind the side panel should be positioned on the righthand side. Positioning of monitorbracket 1. Mount the hangingbrackets on the right (or left) side of the machine. 2.
4 Positioning / Installing the machine 9 Before proceeding any further: Take the installation manual out of the computer packaging and look up the connection information. This provides a clear description of all computer cables and plugs and the correct way to connect them. 4.3.3 Installing the computer system (see figure 5) 1. Position the keyboard (number 2), the monitor (number 3) and the computer (number 4) as shown in figure 5. 2.
5 Operation 5.1 10 Brief overview and function of the operating elements (HA-s/m/l) See figure 6 (elements shown with a dotted outline are located inside the machine). 1. Main switch (red) ⇒ Switching the whole machine on and off 2. Monitor ⇒ Monitoring and coordinating the process 3. Keyboard (various versions) ⇒ Controlling the process 4. Computer ⇒ Input and output control unit 5. Lift table unlocking pedal ⇒ Unlocking the lift table 6.
5 Operation 5.
5 Operation 5.3 12 Starting the machine 5.3.1 Preparing the machine for use for the first time 1. Turn the red main switch (see figure 6, number 1) to position You are advised to leave this switch turned on at all times. This is necessary for the automatic stirring system. It also reduces wear on the machine and the computer system. Then turn also the green switch (see figure 6, number 12) to position . Now the computer is turned on. Switch the computer off at the end of the day. 2.
6 Maintenance 6.1 13 Maintenance instructions Always remove the power cord from the mains socket before commencing any maintenance work on the machine. 1. Servicing and repairs may only be carried out by qualified personnel. 2. Use good quality, appropriate tools only. 3. Use original Fluid Management parts only. 4.
6 Maintenance 6.3 14 Troubleshooting Before calling in the Service Department, check whether you can solve the problem yourself. If you cannot, call the Service Department for advice (see 6.4). Have the model number and serial number to hand. They can be found on the nameplate on the machine (see 7.1). Use the chart of Problem, Cause and Action below to judge whether you can solve a problem yourself or whether you will need to call in the Service Department.
6 Maintenance 15 ð Stirrer is not rotating ð Turntable is not turning 1. Loose cable 2. Timer setting incorrect 3. Defective cable 4. Defective motor 5. Wingdoor or front door open 1. Door and/or lid not closed properly 2. Piston rod positioned too high 3. Valve mouth pointing down 4. Cable(s) loose 5. Cable or motor defective 1. Check cable 2. Use the software to set the timer correctly 3. 4. 5. Close the door(s) ð 1. Close door and/or lid 2. Set piston in lowest position 3.
6 Maintenance 16 If necessary, you can get in touch with your supplier or the local service department, or contact the manufacturer directly. If you contact the manufacturer, make sure that you have the model number and serial number to hand. They can be found on the nameplate on the machine (see 7.1). Fluid Management Europe B.V. P.O. Box 220 2170 AE Sassenheim, the Netherlands Hub van Doorneweg 31 2171 KZ Sassenheim, the Netherlands Tel.
7 Machine identification data 7.1 17 Machine plate data To reach the machine plate, first open the front door of the machine. The plate is situated on the right side in the computer space. P.O.Box 220 2170 AE Sassenheim, Holland V~ Hz W Weight kg A Model nr.: Serial nr.
7 Machine identification data 7.2 Pictures of the machine parts 7.2.
7 Machine identification data 7.2.
7 Machine identification data 7.2.3 20 Power unit and sensor position A. Standard Power unit machine fuse 2A Sensor 6 Sensor 4 Sensor 2 Sensor 5 B.
8 Specifications 21 C. Ha-l fuse 6.
A-weighted equivalent continuous sound pressure level.
A-weighted equivalent continuous sound pressure level.
A-weighted equivalent continuous sound pressure level.
