Brochure

63
OEM DIRECT
Replacement Models
1/35-1/100 115 1.4-.5 1550 2 D534 E SP Band 3.3 C.W. 2-1/2 1/4 x 1 12324 L
1" Stack 115 1.1 3000 1 K161 H SP Stud – C.C.W. – .2178 x 1.15
Many Freezer Case
Applications
1/4 208-230 2.2 1075 1 D1091 I PSC Band 5 C.C.W. 4-1/2 1/2 x 2-3/4
35035B001, 322P859,
DE3L038
— 230 .5 3000 1 A081
•
^† J SP — 3.3 C.C.W. — —
35035B001, 322P859,
DE3L038
MATHIESEN
1/10-1/20 115 3.9/1.7 1050 2 D177 L SP Stud 5.12 C.C.W. 2-5/8 3/8 x 3-5/8 6125-366/6
MCMILLAN
1/3 115 1.1 1550 1 D1008 K SP Lug 4.4 C.W. 3 1/2 x 1-7/8
OLM6151, 322P151
LOMANCO
MAGIC CHEF
McQUAY
MIAMI/CAREY
1/25-1/35-1/65 115 1.1-.9-.6 1200 3 D1144 # B PSC Stud 3.3 C.W. 4-3/4 3/8 x 5-5/8 BA2H015
1/15 115/230 1.7-.9 1500 1 D1142 A SP Stud 3.3 C.W. 3-1/2 5/16 x 2-1/2 879-382-562 ZB-00
1/10-1/12-1/15 115
2.2-2.0
1500 3 D1140 + C PSC Base 3.3 D.S. 4-3/4 5-5/8 x 3/8 x 5-5/8 879-382564B-00
1.7
1/15-1/25-1/35 115
1.7
1000 3 D1141 # C PSC Base 3.3 D.S. 4-3/4 5-5/8 x 3/8 x 5-5/8 879-382563B-00
1.1-.9
F2417-121479
3/4-1/2 460 2.5-1.6 1075 2 D915•‡
★
D PSC Band 5.6 Rev. 5-1/3 5/8 x 4-1/2 Marathon
EWB48A110558AE
H.P. Volts Amps RPM Spd. Model Fig. Type Mtg. Dia. Rot.
"A" Shaft Dia.
Reference No.
Dim and Length
+ 7.5M 370V capacitor • Ball bearing motor ‡ Not a direct replacement for 253-1194, but is an acceptable substitute.
★ 15M 370V capacitor # 4M 370V capacitor ^ Stainless steel shaft † Replacement for Airease
▼▼
MILLER
MILLER 103080002,
1/8 115 6.0 1070 1 D1082 F SP Lug 5.0 C.W. 4 1/2 x 3-1/4 FASCO 7152-0020,
U.E.-DA3F130N
MMG Series 80 & 100
1/6 115 6.6 1050 1 S156 G SP Base 5.0 C.W. 3-1/2 1/2 x 3-7/8 MOC Series 80 & 100
CFM Series 80 & 100
Fig. A D1142 Fig. C D1140, D1141 Fig. E D534 Fig. G S156
Fig. B D1144 Fig. D D915
Fig. F D1082
Fig. I D1091
Fig. H K161
Products on this page are
NOT SUITABLE for unattended
equipment unless indicated by
symbol. See inside back cover for
additional information.
PSC motors use 5M
370V capacitors unless
otherwise indicated.
Fig. J A081
Fig. K D1008
Fig. L D177
NOTE: Rotation is determined by looking at shaft end. Shaft length is measured from motor face.
NEW
NEW