Selection Guide

General Purpose Motors

3.3" Diameter

FASCO

MODEL

TYPE HP VOLTS RPM SPD. AMPS ENCLOSURE ROT. BRNG. SHAFT DIM.

“A”

DIM.

FIG. NOTES

D1127 PSC 1/12-1/15-1/20 115/230 1550 1 1.1/0.6 Open Vent. REV SLV 5/16 x 3 3 1/2 A

D107 SP 1/160 208-240 600 1 0.5 Open Vent. CCW SLV 5/16 x 1 2 5/8 B 15

D129 SP 1/125-1/200 115 1500 2 .4-.3 Open Vent. DS SLV 3-1/4 x 1/4 x 3-1/4 2 1/8 C 15,22

D1119 SP 1/90 240 1500 1 0.34 Open Vent. CCW SLV 1/4 x 1-1/2 2 1/4 D 15

D120 SP 1/70 115 1500 1 0.7 Open Vent. CW SLV 1/4 x 2-1/4 2 1/8 E 15

D121 SP 1/70 115 1500 1 0.7 Open Vent. CCW SLV 1/4 x 2-1/4 2 1/8 E 15

D1134 SP 1/50-1/65-1/80 115 1500 3 1.1-.8-.6 Open Vent. CW SLV 1/4 x 1-3/4 2 1/4 F 15

D609 SP 1/50 115 1500 1 0.9 Open Vent. CCW SLV 1/4 x 2-1/4 2 3/16 E 15

D603 SP 1/50 115 1500 1 0.9 Open Vent. CW SLV 1/4 x 2-3/8 2 3/16 E 15

D126 SP 1/40 115 1500 1 1.1 Open Vent. CW SLV 5/16 x 2-1/4 2 1/2 E 15

D127 SP 1/40 115 1500 1 1 Open Vent. CCW SLV 5/16 x 2-1/4 2 1/2 E 15

D128 SP 1/40-1/50-1/80 115 1500 3 1.3-.9-.6 Open Vent. DS SLV 4 x 5/16 x 4 2 1/2 C 15

D190 SP 1/40 230 1500 1 0.6 Open Vent. CW SLV 1/4 x 2-1/4 2 1/2 E 15

D106 SP 1/40 115 1500 1 0.9 Open Vent. CCW SLV 1/4 x 1-3/4 2 1/8 G 15

D105 SP 1/37 115 1500 1 0.94 Open Vent. CCW SLV 1/4 x 1-1/2 2 1/8 G 15

D136 SP 1/30 115 1500 1 1.3 Open Vent. DS SLV 2 x 5/16 x 2 3 1/4 C 15

D514 SP 1/30 115 1500 1 1.3 Open Vent. CW SLV 5/16 x 2-1/4 2 3/4 H 15

D515 SP 1/30 115 1500 1 1.3 Open Vent. CCW SLV 5/16 x 2-1/4 2 5/8 H 15

D532 SP 1/30-1/112 115 1500 2 1.4-.8 Open Vent. CW SLV 5/16 x 1-1/2 2 3/4 E 15

D181 SP 1/30-1/40 115 1500 2 1.3-1 Open Vent. CCW SLV 5/16 x 2-1/4 2 5/8 E 15

D332 SP 1/25-1/65 115 1500 2 1.5-.8 Open Vent. CW SLV 5/16 x 2 3 1/4 I 15

D364 SP 1/25 115 1500 1 1.8 Open Vent. DS SLV 1-7/8 x 5/16 x 1-7/8 2 7/8 J 15

D365 SP 1/25 115 1500 1 1.8 Open Vent. DS SLV 1-7/8 x 5/16 x 1-7/8 2 7/8 K 15,23

D184 SP 1/25 115 1500 1 1.2 Open Vent. CW SLV 5/16 x 1-7/8 3 L 15,24

D636 SP 1/25 230 1500 1 0.69 Open Vent. DS SLV 2-1/4 x 5/16 x 2-1/4 3 1/4 M 15

D132 SP 1/20 115 1500 1 1.8 Open Vent. CW SLV 5/16 x 2-1/4 2 3/4 N 15

D133 SP 1/20 115 1500 1 1.8 Open Vent. CCW SLV 5/16 x 2-1/4 2 3/4 N 15

D188 SP 1/20 230 1500 1 0.9 Open Vent. CW SLV 5/16 x 2-1/4 2 7/8 N 15

NOTES: 15: Air Over 22: Impedance Protected 23: Has hubs for end rings 24: Closed construction

FIG. A D1127 FIG. B D107 FIG. C D129, D128, D136 FIG. D D1119 FIG. E D120, D121, D609,

D603, D126, D127,

D190, D532, D181

FIG. F D1134 FIG. G D106, D105 FIG. H D514, D515 FIG. I D332 FIG. J D364

FIG. K D365 FIG. L D184 FIG. M D636 FIG. N D132, D133, D188

Thermally protected • UL recognized • CSA or ULc certified

NOTE: Rotation is determined by looking at shaft end. Shaft length is measured from motor face.

NEW ITEM! See page 113 for a complete listing of all our new products.