Installation Instructions
Tip: To eliminate sound transfer and to prevent sagging, we suggest that the
Fasade panels be installed underneath a mineral board ceiling tile or some other
material to weigh the panel down. You may consider purchasing an economical
lay-in mineral board ceiling tile for this purpose. This is not a requirement, just a
suggestion. Please see Steps 3 and 4 below for specic installation details.
1) Determine the number of tiles required. When installing in an existing
suspended ceiling grid, count the number of whole panels and border panels
needed. If installing a new grid system, perform the same count from your grid
layout plan. The deep indentations in the Traditional 3 & 5, Art Deco, Rosette,
Coffer and Dome styles prevent them from being cut in the middle properly
and are not recommended to be used as a border panel. Accordingly, these
styles look best when the Hammered or Flat Panel style panels are used on the
perimeter of the room. All other styles can be cut and used as a border ll panel.
See Fasadeideas.com for more information.
2) If installing ceiling grid covers. Install the ceiling grid covers prior
to installing the ceiling panels. Consult GridMAX
®
installation guide for the
necessary steps. (GridMAX
®
installation information can be found at:
acpideas.com)
INSTALLATION
INSTALLATION TIP
Tape
measure
Tin snips
or scissors
Utility
knife
Steel
straight edge
Tools and items you will need:
2' x 2' or 2' x 4' Lay-In Ceiling
– for T-bar grid systems
Lay-In
2' x 2'
Lay-In
2' x 4'
or
3) Installing the border panels. Measure the distance from the center of
the T-Bar to the closest edge of the wall molding. Measure and cut panel to
this size. Tilt on an angle and insert the new tile underneath the existing ceiling
panel. When installing the panels, and if using mineral board as stated above,
place small amounts of Loctite
®
PL Premium or Premium Fast Grab adhesive
on the back side of the Fasade panel to reduce sag.
4) Installing full panels. Working across the room, install the full panels
using the same technique. When installing the panels, and if using mineral
board as stated above in the installation tip, place small amounts of adhesive
on the back side of the Fasade panel to reduce sag.
5) Clean up. Once you have your ceiling installed, the panels can be cleaned
with warm, soapy water.
CAUTION: Even though these panels are “Class A” re rated, they can be deformed with
excessive heat. Never expose to heat over 140˚F.
Never use abrasive materials such as scouring pads to clean surface; use only a soft cloth or
sponge with mild soap and water.
READ this entire installation guide before beginning your installation
Fasade
®
Lay-In Accessories (in Matching Finishes)
Grid Covers - GridMAX
®
grid covers are the low-cost alternative to replacing or repainting rusted, stained or
deteriorated metal grid. Colors match Fasade ceiling panels for lay-in applications.
GridMAX Kit components: 4' wall molding covers, 4' main covers and 2' tee covers. Covers 100 sq. ft.
Suspended Vinyl Grid System - HG-Grid
®
is a high-performing vinyl grid ceiling system designed to withstand
humid conditions. It easily installs like most conventional metal systems without the extreme cost of corrosion-
resistant metal systems.
HG-Grid Kit components: 8' Main Runners, 2' Cross Tees and 8' Wall Brackets. Covers 100 sq. ft.
Surface Mount Grid System - CeilingMAX
®
is engineered for direct application over plaster, drywall and glue-up
ceilings. This surface-mounted grid system saves up to 6" of ceiling height.
CeilingMAX Kit components: 8' Wall Brackets, 8' Runners, 8' Top Hangers and 2' Cross tees. Kits come in 64 sq. ft.
or 100 sq. ft.
Matching Accessories for Fasade Lay-in Ceilings for new and existing ceilings
(Purchased separately)
All these styles
have a at lip on
each edge to lay
in grid.
Loctite
®
PL Premium
®
or PL Premium
®
Fast
Grab adhesive
(optional)