FAQ

ManualsBrandsFasade ManualsOtherBorder Fill 2 ft. x 4 ft. Glue Up Vinyl Ceiling Tile in Cracked Copper (40 sq. ft.)

How do I need to prepare the ceiling before I install the glue up tiles?

If you are planning to install glue up tiles to your ceiling, you need to make sure your ceiling is

clean. We recommend that you apply a fresh coat of primer or paint on the ceiling before the

panels are installed. Also, be sure to clean the back of each panel with rubbing alcohol before

applying adhesive. Acceptable substrates are drywall, plaster or clean, smooth tile (glazed,

porcelain type tile; not porous or textured). Any damaged, loose or uneven areas must be

repaired, patched, leveled and primed. Fill cracks and irregularities with wallboard compound or

spackling, then sand smooth with fine-grade sandpaper. Any porous material like highly textured

drywall, plywood (or any raw wood without primer), and wallpaper unless removed, sanded and

primed, will result in adhesive failure.

What can I use to cut the ceiling tiles?

To cut the ceiling tiles use a utility knife, scissors or a tin snips.

What kind of adhesive do I need to install the glue-up panels?

The preferred method for installing Glue-Up ceiling panels is to apply the adhesive directly to

the back of the panels. Then use use a notched trowel (1/4 x 1/4 x 3/4) and spread the adhesive

evenly on the panel. ACP, the manufacturer of Fasade recommends using Loctite PL Premium

adhesive. Do not use double-sided tape to install ceiling panels.

If I choose to use the Tube Adhesive, how much do I need to purchase?

When gluing up the ceiling panels, you will need 1 (10.5 oz) tube for two 2×4 tiles.

What is J-trim and do I need to use it?

J-Trim is a 4 piece that is available to you to use along the edge of your ceiling. The trim is not

required, but does give your ceiling a nice, finished look. The trim pieces are available in the

same colors as the tiles.

Can the ceiling panels be cleaned?

Once you have your ceiling installed, the tiles can be cleaned with warm soapy water. Any harsh

abrasives or chemicals will damage the finish on the tiles.

Can I use Fasade panels in my shower?

No, the adhesive is not engineered to be used in a wet environment such as a shower.

What tools will I need to install the ceiling tiles?

To install your ceiling panels, you will need the following:

Summary of content (4 pages)

PAGE 1
How do I need to prepare the ceiling before I install the glue up tiles? If you are planning to install glue up tiles to your ceiling, you need to make sure your ceiling is clean. We recommend that you apply a fresh coat of primer or paint on the ceiling before the panels are installed. Also, be sure to clean the back of each panel with rubbing alcohol before applying adhesive. Acceptable substrates are drywall, plaster or clean, smooth tile (glazed, porcelain type tile; not porous or textured).
PAGE 2
       Tape Measure Tin Snips or Scissors Caulking gun or 1/4-notched trowel Utility Knife Steel Straight Edge Adhesive (Loctite PL Premium) Permanent Marker During the installation of my ceiling, some of the adhesive dried on the finish side of my panels. How can I remove that? If some of the adhesive has dried on the finish side of the panels, you can use mineral spirits to remove it. This is the only solvent that can be used that will not damage the finish on the tile.
PAGE 3
Products, customer satisfaction is our number one priority and we will be happy to provide any additional information, technical specs or data you may need on any of our products. Can I paint Fasade ceiling panels? Yes. Our Matte White panels are paintable. To paint our white ceiling panels, the recommended paint and preparation steps are below.
PAGE 4
Manufactu rer Paint Preparati Preparation on 1 2 Prime & Finish (P801) rior DTM Acrylic Gloss Industrial Enamel (8000 SERIES) Rust-Oleum Universal Clean & Rust-Oleum and Painter’s None Degrease Touch 2X aerosols Application Type Brush: Nylon or Polyester Roller: 3/8 nap cover Can I use Fasade panels outdoors? Unfortunately, no. Fasade panels are made of PVC plastic which can handle high humidity rooms, kitchens, dining rooms, bedrooms, bars, basements, bathrooms, and family rooms.