Safety Manual
l
Carry the laser scanner separately from its equipment or, for
optimal protection, use the original transport case.
l
When shipping and transporting the laser scanner by rail, sea,
air, or road, use its original transport case and a suitable outer
cardboard box for optimal protection against shock and vibra-
tion.
l
The FARO batteries are lithium-ion batteries and are thus clas-
sified as dangerous goods. When transporting or shipping the
FARO batteries, ensure that you observe all applicable local and
international rules and regulations. For further information, con-
tact your local carrier before transportation or shipping.
Storage
Prior to storing the laser scanner for prolonged periods:
1. Remove the battery.
2. Pack the scanner and the battery in its shipping case to protect it
from environmental hazards, dust, and dirt.
3. Store all components in an environment where:
n
The humidity level is low
n
The temperature is relatively stable
n
The components are not be subjected to extreme tem-
peratures, environmental conditions, or heavy vibrations
Servicing
Servicing and repair must only be done by qualified service per-
sonnel authorized by FARO. Unplug the product from the power out-
let and remove the battery. Request servicing, then deliver it to
qualified service personnel under the following conditions, if:
l
the power-supply cord or plug is damaged.
l
the product has been exposed to rain, water, or other liquids.
l
the product has been dropped or damaged in any way.
l
objects have fallen onto the product.
l
the product does not operate normally when following the oper-
ating instructions.
l
the product exhibits a distinct change in performance.
l
the required service and calibration date is reached.
Nameplate symbols
Indicates conformity with health, safety, and envir-
onmental protection standards for products sold
within the European Economic Area.
Indicates that the product should not be discarded as
unsorted waste but must be sent to separate col-
lection facilities for recovery and recycling.
Indicates that the battery should be recycled in an
environmentally suitable way.
Indicates that the battery should neither be incin-
erated nor set on fire.
Indicates that documentation is provided and
required to use the product.
Indicates that there are no user serviceable parts
inside the housing.
The nameplate on your FARO device may contain
this symbol. It indicates that FARO has provided
important information in the user manual regarding
intended use and safety. Read this information
before using the device.
Indicates that the product contains components with
the Recognized Component Mark, which is a type of
quality mark issued by Underwriters Laboratories
(UL).
FOCUS Premium and FOCUS Core Safety Manual
3
Indicates that the device is for indoor use only.
Parts and Their Functions
Display Side
(See Figure 1-2 on page i.)
①
Power On/Off button - Press for a few seconds (until the LED
blinks) to turn on the FOCUS Premium and FOCUS Core. If the
scanner is on and running, press again to turn it off. You must
confirm shutoff by tapping on the display.
NOTE: In exceptional cases, such as if the shut-down mechanism
does not work or the scanner is non-responsive, press and hold
the button until the scanner shuts down.
②
Touchscreen display
③
Accessory bay 1
④
Accessory bay 2
NOTE: Ensure that the contacts in the accessory bay are clean
before using. If not, clean with a cotton swab soaked in isopropyl
alcohol.
Battery Side
(See Figure 1-3 on page i.)
①
Battery compartment cover
②
Socket to plug in the external power supply
(ACCS-PWR-0010)
③
LED showing battery status
④
SD card slot
Front Side
(See Figure 1-4 on page i.)
①
Status Indicator
②
Scanner mirror - For safety and cleaning instructions, refer to
the Maintenance chapter of the user manual.
③
Reference area - Used for self-referencing the distance meas-
urements while scanning. Keep this area clean and do not peel of
the sticker.
④
Scanner mount
Bottom Side
(See Figure 1-5 on page i.)
①
Cooling fan openings - Keep these openings uncovered and at
least 18 cm (7 in) from the floor or any other surface.
②
M5 screw threads - To mount the scanner to customer-specific
fixtures.
③
Type label
④
Automation Interface
NOTE: The scanner base interface is not available on all scanner
models.
⑤
3/8" screw thread - To mount the scanner to standard photo tri-
pods.
⑥
Battery compartment cover release mechanism
⑦
USB-C port / service & maintenance port (cover not shown)
NOTICE: Do not plug any type of charger into this connector.
Only USBslave devices may be attached.