1.
Interface | Description Camera Get the video, “The door fans has 8 Ult-n speaker for conventional communicant SPAS | and mart ima. we “The door phone has a microelectronic hidden h the pinhole located on the front panel. RID Reader | Liz RID cards to unlock the door by touching RID reader of device.
Network Conn actor Power and Electroshock Connector +DC12V | vss NC CoM NO SIN | s-out 12V DC Input Electric-lock witch Indoor swatch Jp! Jumper Hers are two modes for power supply of electric-lodk as shown in the picture below. (The default Ia "Passive Modern. Passive Mode: When the electric-iock starting current Is more then 12V/S00mA, heed & uae the textual drive mods, the electric lock interface for short circuit output control.
Wiring Instructions NO: Normally Open Contact COM: Common Contact.
Installation Man Part of Intercom Back Panel ‘Walk mounted hanging she Figure 1 Three Major Parts of 130 Step 1: Installation preparation > RAG plugs x 2 (1 spare} > KAA X 26MM Crows X 4 > 26mm screw anchors xd B. Tools that may be required: > Hex ranch > Phillips screwdriver (P2 or Ph), hammer, RIS crisper > Electric Impact dell with an 6mm drill bit Step 2: Drilling A Place the mounting tam plats dni ch ceo sn a desired flat Boe am disco loss marked on the mounting templates.
Step 3: Removing hanging she A. Remove the hanging shall In Figure 3 and Figure 4. pr. Figure 3 Figure 4 B. With Philips screwdriver, unpacks the Back Panel and the main part of Intercom 8 shown in Figure 5. Figure 5 Stop 4: Hanging shall Fixing an Caving Figure & A. Select the hole for cable supply; cable length of 15cm to 20cm is recommended. B. With 4 KAS x 25mm screws, tighten the Wall-mound hanging shell as shown in Figure 5.
JA Figures 7 A. Select tha hols for cable supply. B. Tractor the cables of RJ4G, power, and electric-lock to the motherboard socket 2a ‘mentioned In connectors description {refer to Tactician 2). C. Test whether their Is electricity by doing the following: Press the # button for 3 seconds to get the IP address of Inferior by voice. Input accosts password or press tha Pindar switch fo check electrician Installation. Note: Do nat proceed mounting unt you have finished the electric checking.
4.Searching Door Phone ‘Hers arm bwo methods as shown barrow to search the 10. M tha Door Phone Network Scanner. Press the Refresh bunion to search the i30 and find the [P address. Method 2; Press and hak the “kay for 3 seconds and the door phone will Apart the IP address by voice. : 1 Default Setting Default CPD Cle. Enable Static IP Address 192.168.1.
5.SIP Door Phone Setting Tap 1: Login the homepage of the 130. Step 2: Add the SIP account. ‘Set SIP server address, por, user name, password and SIP user with assumed SIP ‘account parameters. Select "Activate", and then click Apply to save this setting. Step 3: Setting DSS key Set the DSS key a8 shown below for a quick start. Click “Apply” to eave this setting. Type: Hot Key Number 1: The DSS Key wil dial to this Number 1. Number 2 If Number { is unavailable, K wil be forwarded to Number 2.
Step 4: Door Phone Setting 6. Daor Unlocking Setting Local {1)Local Password Step 1: Go to EGS Setting — Features —» Sot Local Password (The default fs “67697. Sta 2: Use the device's Numeric Keyboard fo input password end kay, and then the door wil be unlocked.
(2)Private Access Code Step 1: Go to EGS Cossack + Access Russ — sat Access Coda. Sta 2: Uno the advice's Numeric Keyboard tn Input password and *¥ key, and then the door wil be unlocked. Re mots Remote Password Step 1: Go to EGS Setting — Features — Set Remote Password (The default Is Step 2: To answer the cal made by visitor via SIP phone, press the ™ key to unlock the door the Victor. RID Card Step 1: Ga to EGS Access — Enter the Name and ID Number (Only Fr art 10 yards) Cross Add to Access Table.
