User Manual i16V&i32V Software Version: 2.4.
Directory Directory...............................................................................................................................................................１ 1 Picture.............................................................................................................................................................３ 2 Table..........................................................................................................................................................
9.7 System >> FDMS..................................................................................................................................22 9.8 System >> Tools................................................................................................................................... 22 9.9 Network >> Basic................................................................................................................................. 23 9.10 Network >> VPN...................................
1 Picture Figure 1 - Panel.................................................................................................................................... 5 Figure 2 - Quickly setting.....................................................................................................................6 Figure 3 - WEB Login..........................................................................................................................6 Figure 4 - Line Registered ...........................
４ Figure 37 - Hot Key Settings.......................................................................................................... 52 Figure 38 - Multicast Settings........................................................................................................53 Figure 39 - Advanced Settings.......................................................................................................
2 Table Table 1 - Common command mode............................................................................................... 4 Table 2 - Function key LED state.........................................................................................................4 Table 3 - Panel introduction................................................................................................................. 5 Table 4 - Intercom...................................................................
3 Safety Instruction Please read the following safety notices before installing or using this unit. They are crucial for the safe and reliable operation of the device. Please use the external power supply that is included in the package. Other power supply may cause damage to the phone and affect the behavior or induce noise. Before using the external power supply in the package, please check the home power voltage. Inaccurate power voltage may cause fire and damage.
4 Overview i16V is a SIP visual intercom and i32V is a SIP video door phone developed for industry users on the basis of over ten years of VoIP phone technology. The voice transmission is based on the standard IP/RTP protocol, and the video transmission on RTSP protocol. They inherit Fanvil IP phones’ advantages like good stability and tele-grade sound quality, and perfectly compatible with all current SIP-based main IP PBX/ soft switch /IMS platforms, such as Asterisk, Broadsoft, 3CX, Elastix, etc.
5 Install Guide 5.1 Use POE or external Power Adapter i16V&i32V, called as ‘the device’ hereafter, supports two power supply modes, power supply from external power adapter or over Ethernet (POE) complied switch. POE power supply saves the space and cost of providing the device additional power outlet. With a POE switch, the device can be powered through a single Ethernet cable which is also used for data transmission.
5.2 Appendix Table 5.2.
6 Basic Introduction 6.1 Panel Overview i32V i16V Figure 1 - Panel Table 3 - Panel introduction Number Name Description 1 IP Camera Video signal acquisition and transmission 2 Speaker Play sound 3 Speed dial button 4 MIC Collect voice 5 Card reader area RFID card reader area,supports IC card and ID card For speed dial, multicast, intercom, IP broadcast and other functions 6.
seconds (please do not operate within 30 seconds when power on), the voice will automatically play the IP address of the device or use the "IP scanning tool. exe" software to find the IP address of the device. （Download http://download.fanvil.com/tool/iDoorPhoneNetworkScanner.
The username and password should be correct to log in to the web page. The default username and password are "admin". For the specific details of the operation of the web page, please refer to 9 Web Configurations 6.4 SIP Configurations At least one SIP line should be configured properly to enable the telephony service. The line configuration is like a virtualized SIM card.
3) The other device calls the door phone, enters the corresponding remote authentication code, and opens the door after timeout or the password check length is reached (the authentication code shall be configured in the access list, and the remote telephone opening shall be enabled). 4) Open the door by swiping the RFID card, which supports IC card and ID card. 5) Indoor door opening, the door can be opened through the indoor door button when the door phone is in any state.
7 Basic Function 7.1 Making Calls After setting the function key to Hot key and setting the number, press the function key to immediately call out the set number, as shown below: Figure 5 - Function Setting See detailed configuration instructions 9.27 Function Key 7.2 Answering Calls After setting up the automatic answer and setting up the automatic answer time, it will hear the ringing bell within the set time and automatically answer the call after timeout. Cancel automatic answering.
Figure 6 - Set Release 7.4 Auto-Answering The user can turn off the auto-answer function (enabled by default) on the device webpage, and the ring tone will be heard after the shutdown, and the auto-answer will not time out. Web interface: enter [EGS Setting] >> [Features], Enable auto answer, set mode and auto answer time and click submit.
The range can be set to 0~60s , and the call will be answered automatically when the timeout is set. 7.5 DND Users can turn on the do-not-disturb (DND) feature on the device's web page to reject incoming calls (including call waiting).Do not disturb can be set by the SIP line respectively on/off. Turn on/off all lines of the device without interruption by the following methods: Web interface: enter [EGS Setting] >> [Features], set the DND Mode to phone and Enable DND.
7.6 Call Waiting Enable call waiting: new calls can be accepted during a call. Disable call waiting: new calls will be automatically rejected and a busy signal will be prompted Enable call waiting tone: when you receive a new call on the line, the device will beep. Users can enable/disable call waiting in the device interface and the web interface. Web interface: enter [EGS Setting] >> [Features], enable/disable call waiting, enable/disable call waiting tone.
8 Advance Function 8.1 Intercom The equipment can answer intercom calls automatically. Figure 11 - WEB Intercom Table 4 - Intercom Parameters Description Enable Intercom Mute Enable mute during intercom mode Enable Intercom Ringing 8.2 If the incoming call is intercom call, the device plays the intercom tone. MCAST This feature allows user to make some kind of broadcast call to people who are in multicast group.
Figure 12 - MCAST Table 5 - MCAST Parameters Description Enable Auto Mcast Send the multicast configuration information by Sip Notify signaling, and the device will configure the information to the system for multicast listening or cancel the multicast listening in the system after receiving the information Auto Mcast Timeout When a multicast call does not end normally, but for some reason Delete Time the device can no longer receive a multicast RTP packet, this configuration cancels the listening af
Press the DSSKY of Multicast Key which you set. Receive end will receive multicast call and play multicast automatically. 8.3 Hotspot SIP hotspot is a simple utility. Its configuration is simple, can realize the function of group vibration, can expand the number of SIP account. Take one device A as the SIP hotspot and the other devices (B, C) as the SIP hotspot client.
Figure 13 - SIP Hotspot The device is the hotspot server, and the default extension is 0.The device ACTS as a client, and the extension number is increased from 1 (the extension number can be viewed through the [SIP hotspot] page of the webpage).
9 Web Configurations 9.1 Web Page Authentication Users can log into the device's web page to manage user device information and operate the device. Users must provide the correct user name and password to log in. If the password is entered incorrectly three times, it will be locked and can be entered again after 5 minutes.
9.3 System >> Account Figure 14 - WEB Account On this page the user can change the password for the login page. Users with administrator rights can also add or delete users, manage users, and set permissions and passwords for new users 9.4 System >> Configurations Figure 15 - System Setting On this page, users with administrator privileges can view, export, or import the phone configuration, or restore the phone to factory Settings.
import, and the configuration will take effect after restart Reset Phone The phone data will be cleared, including configuration and database tables. 9.5 System >> Upgrade Figure 16 - Upgrade Upgrade the software version of the device, and upgrade to the new version through the webpage. After the upgrade, the device will automatically restart and update to the new version. Click select, select the version and then click upgrade 9.
Details refer to Fanvil Auto Provision http://www.fanvil.com/Uploads/Temp/download/20180920/5ba38170d79fb.pdf Table 7 - Auto Provision Parameters Description Basic settings Show the current config file’s version. If the version of configuration Current downloaded is higher than this, the configuration will be upgraded.
Custom Option Value Enable DHCP Option 120 Custom option number. Must be from 128 to 254. Set the SIP server address through DHCP option 120. SIP Plug and Play (PnP) Whether enable PnP or not. If PnP is enable, phone will send a SIP Enable SIP PnP SUBSCRIBE message with broadcast method. Any server can support the feature will respond and send a Notify with URL to phone. Phone could get the configuration file with the URL. Server Address Broadcast address. As default, it is 224.0.0.0.
Enable the STUN 9.7 Enable the STUN System >> FDMS Figure 18 - FDMS Table 8 - FDMS FDMS information Settings Community Designations Name of equipment installation community Building a movie theater Name of equipment installation building room number Equipment installation room name 9.8 System >> Tools This page gives the user the tools to solve the problem.
Syslog：When enabled, set the syslog software address, and log information of the device will be recorded in the syslog software during operation. If there is any problem, log information can be analyzed by Fanvil technical support.
mask Default gateway MAC MAC Time stamp The current Gateway IP address The MAC address of the equipment Get the MAC address of time. Settings Select the appropriate network mode. The equipment supports three network modes: Static IP DHCP PPPoE Network parameters must be entered manually and will not change. All parameters are provided by the ISP. Network parameters are provided automatically by a DHCP server. Account and Password must be input manually. These are provided by your ISP.
access. Example: The IP address is 192.168.1.70 and the port value is 8090, the accessing address is http://192.168.1.70:8090. Port for HTTPS access. Before using https, an https authentication HTTPS Port certification must be downloaded into the equipment. Default value is 443. To enhance security, change this from the default. 9.
non-encrypted data tunneling. For users who need data encryption, please use OpenVPN instead. To establish a L2TP connection, users should log in to the device web portal, open webpage [Network] >> [VPN]. In VPN Mode, check the “Enable VPN” option and select “L2TP”, then fill in the L2TP server address, Authentication Username, and Authentication Password in the L2TP section. Press “Apply” then the device will try to connect to the L2TP server.
Figure 22 - WEB Filter Figure 23 - WEB Filter Table Add and remove IP segments that are accessible; Configure the starting IP address within the start IP, end the IP address within the end IP, and click [Add] to submit to take effect. A large network segment can be set, or it can be divided into several network segments to add. When deleting, select the initial IP of the network segment to be deleted from the drop-down menu, and then click [Delete] to take effect.
9.12 Line >> SIP Figure 24 - SIP Configure the service configuration for the wire on this page.
Table 10 - SIP SIP Field Name Explanation Basic Settings (Choose the SIP line to configured) Line Status Display the current line status at page loading. To get the up to date line status, user has to refresh the page manually. Username Enter the username of the service account. Display name Enter the display name to be sent in a call request.
Anonymous Call Standard Dial Without Registered Set the standard to be used for anonymous Set call out by proxy without registration Click To Talk Set Click To Talk User Agent Set the user agent, the default is Model with Software Version.
device presses the */# key, the actual value sent is */#; Configured to send 10/11, when the device presses the */# key, the actual value sent is 10/11. Transportation Protocol Set the line to use TCP or UDP for SIP transmission Local Port Set the Local Port SIP Version Set the SIP version Caller ID Header Set the Caller ID Header Enables the use of strict routing. When the phone receives packets Enable Strict Proxy from the server, it will use the source IP address, not the address in via field.
9.13 Line >> Basic Settings STUN -Simple Traversal of UDP through NAT -A STUN server allows a phone in a private network to know its public IP and port as well as the type of NAT being used. The equipment can then use this information to register itself to a SIP server so that it can make and receive calls while in a private network.
SIP Settings Local SIP Port Set the local SIP port used to send/receive SIP messages. Registration Failure Set the retry interval of SIP REGISTRATION when registration Retry Interval failed. Enable Strict UA Match Enable or disable Strict UA Match Field Name Explanation STUN Settings Server Address STUN Server IP address Server Port STUN Server Port – Default is 3478. Binding Period SIP Waiting Time STUN blinding period – STUN packets are sent at this interval to keep the NAT mapping active.
Figure 27 - EGS Setting Table 12 - EGS Setting EGS Features Setting (Only for Door phone) Field Name Explanation Basic Settings Monostable: there is only one fixed action status for door unlocking. Bistable: there are two actions and statuses, door unlocking and door Switch Mode locking. Each action might be triggered and changed to the other status. After changed, the status would be kept. Initial Value is Monostable Switch-On Duration Enable Card Reader Door unlocking time for Monostable mode only.
Effective Data Wiegand Data Reverse Set Wiegand Data Reverse, the default value is automatic. Disable remote password implementations for all calls to open doors; Enable Access Table Enable remote password to open the door after calling only by access guard Limit Talk Duration Talk Duration Calling Password Description Enable Open Log Server Address of Open Log Server Port of Open Log Server If enabled, calls would be forced ended after talking time is up.
Enable Auto Answer Enable Auto Answer function Auto Answer Timeout Set Auto Answer Timeout No Answer Handdown Enable automatically hang up when no answer No Answer Auto Configuration automatically hangs up when no answer occurs within Hangup the set time. Auto Hangup Timeout Dial Fixed Length to Send Set the time of no answer auto hangs up. Configure to enable/disable fixed-length automatic dial-out numbers. Configure the receiving number length; default is 4.
9.16 EGS Setting & Intercom Setting >> Audio Figure 28 - Audio Setting Table 13 - Audio Setting Field Name Explanation Audio Settings Codec Setting Select enabled or disabled audio codec: G.711A/U,G.722,G.723,G.729, G.726-16,G726-24,G726-32,G.726-40, ILBC,AMR,AMR-WB, opus DTMF Payload Type Setting DTMF payload type, the value range must be 96~127. Default Ring Type Configure the default ring tone. If no special ringtone is set for the caller number, the default ringtone will be used. G.
Broadcast Output Volume Set the broadcast output volume to 1~9 Signal Tone Volume Set the signal sound volume to 0~9 Enable VAD Whether voice activity detection is enabled. Sound Update Sound Update Can be upgraded suffix ".
Figure 29 - Video Setting Camera connection Settings Field Name Explanation Camera status: When the device is restarted, the camera status shows Camera status whether it is currently available. and number of The maximum number of accesses, the maximum number of main code visits streams, the maximum number of subcode streams and the number of uses.
Night Mode: the camera's video screen is always black and white, if there is IR-cut will be synchronized switch. Automatic: Automatically adjusts according to the actual environment in White Balance which the camera is located. Outdoor: installed in the outdoor preferred. Indoor: installed in the room preferred. Horizon Flip Anti Flicker The video is flipped horizontally Enable the option.
VBR: Image quality is preferred, not recommended. Quality Video quality adjustment, the better the quality needs to transfer faster Bit rate It is proportional to video file size, not recommend adjusted. I Frame Interval Activate The greater the value is, the worse the video quality would be, otherwise the better video quality would be; not recommend adjusted.
lowest. Enable Page Priority Two multicasts, regardless of who first calls in, the device will receive the multicast with higher priority. Name Listened multicast server name Host: port Listened multicast server’s multicast IP address and port. 9.19 EGS Setting & Intercom Setting >> action URL Action URL Event Settings URL for various actions performed by the phone. These actions are recorded and sent as xml files to the server. Sample format is http://InternalServer /FileName.
Month Start The DST start month Week Start The DST start week Weekday Start The DST start weekday Hour Start The DST start hour Month End The DST end month Week End The DST end week Weekday End The DST end weekday Hour End The DST end hour Manual Time Settings Manual Time Settings The time set by hand, need to disable SNTP service first 9.21 EGS Settings >> Trusted Certificates The certificate management page uploads and deletes uploaded certificates. Figure 30 - Trusted Certificates 9.
Figure 31 - Device Certificates 9.
Figure 32 - EGS Access Table 18 - EGS Access Parameter EGS Access Field Name Explanation Import Access Table Click the to choose to import remote access list file (access List.csv) and then clicking can batch import remote access rule. Access Table According to entrance guard access rules have been added, you can choose single or multiple rules on this list to delete operation. Click " " to export the saved access list.
use, and [None] is not limited for 24 hours. Add After the relevant rules are disposed in the "Add Access Rules" sub-item, click "Add" to complete the addition. In the "Access Table", select the "Index" to be modified. After the relevant Modify rules are disposed in the "Add Access Rule" sub-item, click "Modify" to complete the modification.
Figure 33 – EGS Logs Table 19 - EGS Logs Parameter Field Name Explanation Door Open Log Result Show the results door open history ( Succeeded or Failed) Time The door open time. Access If the door was opened by swipe card or remote unlocking door, the device Name would display remote access name. Open type: 1. Local, 2. Remote, 3. Card Note: there are three kinds of card feedback results.
9.25 Door Lock Figure 34 - Door Lock Table 20 - Door Lock Parameter Field Name Explanation Current lock Status Door Sensor Check Alert Enable/disable the door phone alarm. When the timeout period is enabled, the alarm will be triggered when the door status and the door lock status are inconsistent. When choosing the low level trigger (closed trigger), detect the input port Trigger mode (low level) closed trigger.
Door Lock Control Door Lock Execute a door lock to open or close the door Action Door Open/Close Once: perform door opening action, and will be closed automatically Open mode when timeout. Continue: perform the door opening action, the door will not be closed automatically and need to closed manually when timeout. Auto Open Setting SIP Register When the SIP line registration fails, the door lock could be set to open Fail automatically after the timeout period.
Figure 35 - Alert/Security Settings Table 21 - Alert/Security Settings Security Settings Field Name Explanation Input settings Input Detect Enable or disable Input Detect When choosing the low level trigger (closed trigger), detect the input port (low Trigger Mode level) closed trigger. When choosing the high level trigger (disconnected trigger), detect the input port (high level) disconnected trigger.
Duration Input trigger DTMF output Duration When the input port meets the trigger condition, the output port will be triggered (The Port level time change, By < Output Duration > control) By duration Port switch amount change time, press
User=;Mac=00:a8:34:68:23:d1;IP=172.18.90.235;port=Input1 9.27 Function Key Key Event The speed dial key type could be set as Key Event. Figure 36 - Function Key Settings Table 22 - Function Key Settings Type Key Event Subtype Usage None No responding Release Delete password input, cancel dialing input and end call OK Identification key Hot Key When the speed dial key set as Hot Key, the device would dial preset telephone number.
IP address key. In Intercom mode, if the caller’s IP Intercom phone supports Intercom feature, the device can automatically answer the Intercom calls Multicast Multicast function is to deliver voice streams to configured multicast address; all equipment monitored the multicast address can receive and play the broadcasting. Using multicast functionality would make deliver voice one to multiple which are in the multicast group simply and conveniently.
Figure 39 - Advanced Settings Table 25 - Advanced Settings Advanced Settings Field Name Explanation Input port is multiplexed as Enable or disable the input port to be multiplexed as speed dial button 2 function key 2 Use Function Key to Answer Enable Speed Dial Hang up Enable or disable shortcuts to answer calls Enable or disable shortcuts to hang up calls Number 1 call number 2 mode selection.
10 Trouble Shooting When the device is not working properly, users can try the following methods to restore the device to normal operation or collect relevant information to send a problem report to the Fanvil technical support mailbox. 10.1 Get device system information Users can obtain information through the [System] >> [Information] option on the device webpage. The following information will be provided: Device information (model, software and hardware version) and Internet Information etc. 10.
Table 26 - Common Trouble Cases Trouble Case Solution Device could not boot up 1. If the device enters "POST mode" (the SIP/NET and function button indicators are always on), the device system is damaged. Please contact your location technical support to help you restore your equipment system. 2. If the device enters "POST mode" (the SIP/NET and function button indicators are always on), the device system is damaged.
