Installation Guide

ManualsBrandsFanimation ManualsCeiling Fan Light KitsThree Light Bowl Fitter- AB

1. Slide the switch to "RC" if you are using

remote control or wall control with the

light kit. Slide the Switch to "CH" if you

are using pull chain with the light kit.

F5** Light Bowl Fitter Installation Instructions

READ AND SAVE THESE INSTRUCTIONS

Weight: 1.12 lbs (0.51 kgs)

NOTE: This ceiling fan light kit is only meant to be used with ceiling fans. Do NOT install as

a light ﬁxture.

WARNING:

To reduce the risk of ﬁre or electric shock, do not use this fan/light kit with any

solid-state speed control device.

To reduce the risk of ﬁre and electric shock, this kight kit

should be used only with the fan model listed below:

CAUTION CAUTION

at the main fuse box to the fan before installing the light

kit.

Fan Model: Windpointe

Series

2. Remove cover switch housing and

retain the screws for Step 7.

3. Remove threaded plug from cover

switch housing.

Cover Switch

Housing

4. Route wires from light kit through the

supplied large rubber washer, then through

the switch housing and secure cover switch

housing to ﬁtter with lockwasher and nut

provided.

Cover Switch

Housing

5. Locate white and blue wires labeled

“FOR LIGHT”.

6. Connect white-to-white and blue-to

-black wires with wire nuts.

7. Assemble cover switch housing/light

ﬁtter with previously removed screws.

Bulb

Bowl Glass

8. Install LED bulbs in each of the three

sockets.

Assemble bowl glass with rubber

washer, nut and ﬁnial provided, making

sure the fan's pull chain passes through

the bowl glass, rubber washer, nut and

ﬁnial. Do not over tighten.

Finial

Nut

Rubber

Washer

Summary of content (4 pages)

PAGE 1
F5** Light Bowl Fitter Installation Instructions READ AND SAVE THESE INSTRUCTIONS Weight: 1.12 lbs (0.51 kgs) NOTE: This ceiling fan light kit is only meant to be used with ceiling fans. Do NOT install as a light ﬁxture. WARNING: To reduce the risk of ﬁre or electric shock, do not use this fan/light kit with any solid-state speed control device.
PAGE 2
WARNING To reduce the risk of ﬁre, electric shock, and injury to person, must be installed with G1** (bowl glass) that are marked on F5** to indicate the suitability with this model. Other shades cannot be substituted. WARNING To avoid possible ﬁre or shock, make sure that the electrical wires are completely inside the fan housing and not pinched between the switch cup housing and the switch cup ﬂange. 10. Check the operation of the light kit by gently pulling on the pull chain.
PAGE 3
F5** Instrucciones de instalación del ﬁjador de lámpara de techo LEA Y GUARDE ESTAS INSTRUCCIONES Peso: 0,51 kgs (1.12 lbs) NOTA: Los kits de iluminación del ventilador de techo solo deben utilizarse ventiladores de techo. NO LOS instale como unidad de iluminación. ADVERTENCIA: Para reducir el riesgo de incendio o descarga eléctrica, no use este ventilador / kit de iluminación con ningún dispositivo de control de velocidad de estado sólido.
PAGE 4
ADVERTENCIA Para reducir el riesgo de incendio, descarga eléctrica y daño a las personas, debe instalarse con (una tulipa de cristal) G1** que esté marcada con F5**, que indica que el modelo es el adecuado. No se pueden sustituir otras pantallas. ADVERTENCIA Para evitar un posible incendio o descarga eléctrica, asegúrese de que los cables eléctricos estén completamente dentro de la carcasa del ventilador y no estén pisados entre la carcasa del conmutador y el borde de la unidad del conmutador. 10.