Installation Guide

ManualsBrandsFanimation ManualsCeiling Fan Mounting HardwareClose to Ceiling Kit Oil-Rubbed Bronze Stainless Steel Ceiling Fan Mounting Hardware

CCK8002

Close-To-Ceiling Kit

INSTRUCTION SHEET

USE THESE INSTRUCTION IN CONJUNCTION WITH YOUR FANIMATION

FAN OWNERS MANUAL AND IN PLACE OF THE STEPS FOR HOW TO

HANG YOUR CEILING FAN. IF YOU NO LONGER HAVE YOUR MANUAL,

ONE CAN BE DOWNLOADED AT WWW.FANIMATION.COM.

After removing your kit from the packaging, use slight 1.

pressure to push down and remove the screw trim

cover ring from the ceiling canopy assembly. (Figure 1)

Figure 1

SCREW TRIM

COVER RING

CEILING CANOPY

Figure 2

REMOVE

SCREW

LOOSEN SCREWS (2)

BUT DO NOT REMOVE

SLOTTED

REMOVE

SCREW

Separate the ceiling bracket from the ceiling canopy 2.

by loosening the two canopy-to-bracket screws where

the canopy is slotted and completely remove the other

two screws where it is not slotted and set aside for

later. (Figure 2)

Twist the ceiling bracket counter-clockwise and lift out 3.

of the ceiling canopy. There is another short canopy

option when it is needed to very close to ceiling.

(Figure 3)

Figure 3

CEILING CANOPY

Short Canopy

CEILING BRACKET

Safety Instructions

To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not operate fan without blades.1.

All wiring and installation procedures must satisfy National Electrical Codes (ANSI/ NFPA 70-1999) and Local Codes. The ceiling fan must 2.

be grounded as a precaution against possible electrical shock. Electrical installation should be made or approved by a licensed electrician.

The fan base must be securely mounted and capable of reliably supporting at least 50 lbs. Consult a qualified electrician if in doubt.3.

The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades.4.

Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not have adequate electrical knowledge or 5.

experience, have your fan installed by licensed electrician.

6˝ downrod 4.5˝ downrod Tall close-to-ceiling kit Short close-to-ceiling kit

Summary of content (4 pages)

PAGE 1
CCK8002 Close-To-Ceiling Kit INSTRUCTION SHEET USE THESE INSTRUCTION IN CONJUNCTION WITH YOUR FANIMATION FAN OWNERS MANUAL AND IN PLACE OF THE STEPS FOR HOW TO HANG YOUR CEILING FAN. IF YOU NO LONGER HAVE YOUR MANUAL, ONE CAN BE DOWNLOADED AT WWW.FANIMATION.COM. Safety Instructions 1. 2. 3. 4. 5. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not operate fan without blades.
PAGE 2
4. On your fan’s motor, remove the two downrod support set screws and nuts from the downrod support and discard. (Figure 4) NOTE: MOTOR WIRES HAVE BEEN OMITTED FROM DIAGRAM DOWNROD SUPPORT Figure 4 5. Remove the three motor coupling screws from your fan and save for next step. (Figure 5) NOTE: MOTOR WIRES HAVE BEEN OMITTED FROM DIAGRAM METAL SPACER MOTOR Figure 5 6. Route your fan wires through the ceiling canopy and place ceiling canopy onto your motor.
PAGE 3
8. Using the two screws and washers, securely attach the ceiling bracket to the ceiling junction box, making sure to run the supply wires through the hole in the center of the bracket. (Figure 9) NOTE: SUPPLY WIRES HAVE BEEN OMITTED FROM DIAGRAM OUTLET BOX WASHER MOUNTING BRACKET SCREW Figure 9 9. Loop the safety cable through pin hole in motor coupler and put the cable clamp in the end of safety cable. (Figure 10). CABLE CLAMP Figure 10 10.
PAGE 4
13. Lift the fan off the bracket hook and mount your fan by sliding the ceiling canopy over the mounting bracket with the two loosened screws going into the slots in the canopy. Be sure all wiring is tucked into the ceiling canopy and is not pinched. Once the canopy is flush with your ceiling, turn clockwise to seat the screws into the keyed portion of the slot. Tighten the screws. (Figure 13) NOTE: MOTOR WIRES HAVE BEEN OMITTED FROM DIAGRAM SCREW MOUNTING BRACKET SCREW SLOT SLOT Figure 13 14.