T Series Specification

14
T S E R I E S
L O C K F E AT U R E S A N D S P E C I F I C AT I O N S
Lock Features
Door Thickness: 1-3/4” to 2-1/8” standard. Thin door adapter
kit (A30775-000-00) available for doors thinner than 1-3/4”,
please specify door thickness.
Backset: 2-3/4” standard. 2-3/8” also available.
Link (A22161-005-10) available for 5” backset.
Mechanism: Parts constructed of brass or cold formed steel,
zinc plated and dichromated for rust resistance. Springs are
stainless steel.
Attachment: Lock chassis secured to door by threaded mounting
nuts. Completely preassembled outer trim and inner spindle assembly
are through-bolted over chassis using (2) 10-32 screws. Adding
rose and lever to inner spindle assembly completes installation.
Handing: Locks are non-handed.
Cylinders: Drilled with 6-pin chambers, pinned in 5. Pinning in 6
chambers available when specied, at no cost. 7-pin cylinders also
available. Cylinder assemblies removable to rekey. Also available
with 6 or 7-pin interchangeable core cylinders. Cylinder housings
and plugs machined from solid brass. Springs are phosphor bronze.
Two nickel silver keys furnished standard. Interchangeable core
design is available for small format (SFIC) and large format for
most manufacturers, see page 8.
Falcon Lock T Series Specications
Key-in-lever cylindrical locksets shall be Falcon Lock T Series or
equal and meet the following requirements:
• All locks shall meet the new ANSI/BHMA A156.2, Series 4000,
Grade 1 for key-in-lever locksets.
• Locksets shall be UL Listed (3 hour A Label).
• Locksets shall be provided standard with Pressure Release™
feature. When outside lever is locked, it is not rigid but will
move freely without operating the latch bolt.
• Lever trim shall have individual heavy-duty compression springs
behind rose for lever return and to prevent lever sag. Trim shall
be through-bolted with two (2) 10-32 screws coated with thread
sealant to provide strength and resistance to loosening. Inner
Elevation Standard StrikeDoor Edge
Keyways: “G” keyway standard on conventional cylinders. “A”
keyway standard on I/C core cylinders. Also available with some
optional keyways.
Trim: Roses are heavy wrought brass or bronze, installed over
pressure cast rose inserts which are through-bolted through door.
Levers are pressure cast (solid levers–no inserts) material nished
to match mating parts.
Latches: 9/16” bolt projection, UL listed with latch faceplates
2-1/4” x 1-1/8” with square corners standard. 3/4” projection,
UL listed latch with 2-3/4” backset also available. Adjustable front
standard. See page 10 for optional latches.
Strikes: 4-7/8” x 1-1/4” ANSI strike with curved lip to meet ANSI
A115.2 door frame preparation standard. Consult page 11 for
other available strike sizes and congurations.
Screws: Furnished with combination screws for use in wood or
metal doors and frames.
Electried Functions: Available in 24 VDC .185 AMP.
ANSI/BHMA: Meets ANSI/BHMA A156.2, Series 4000, Grade 1.
UL: 3 hour A label.
and outer trim shall “bottom out” to prevent door collapse.
Roses shall be minimum of 3-1/2” diameter.
• All lever designs shall be solid and meet the federal ADA and
state disability requirements. Inside levers shall be attached by
Allen-head set screw to prevent tampering or vandalism.
• Locksets shall adjust to t door thickness from 1-3/4” to 2-
1/8”.
• All locksets shall be non-handed and not require eld
disassembly for re-handing.
• Preparation for door must be non-handed.
Acceptable manufacturer: FALCON LOCK
2-3/8”, 2-3/4”
5/32”5/16” Dia. thru hole
2-3/4”
5/32”
x 1/8”
Deep
2-25/32”
2-1/8” Dia.
1-1/8”
1-1/8”
2-1/4”
1” Dia.
3/4”
3-3/8”
4-7/8”
1-1/4”
5/16”
3-1/2”
4-1/8”
3/8”
9/16”
1-1/16”
C
L
door, lock & strike are common
Backset (from center of door for beveled stile)