Datasheet

FSBB30CH60F Motion SPM® 3 Series
©2006 Fairchild Semiconductor Corporation 7 www.fairchildsemi.com
FSBB30CH60F Rev. C6
Electrical Characteristics (T
J
= 25°C, unless otherwise specified.)
Control Part
2nd Notes:
4. Short-circuit protection is functioning only at the low-sides.
5. The fault-out pulse width t
FOD
depends on the capacitance value of C
FOD
according to the following approximate equation: C
FOD
= 18.3 x 10
-6
x t
FOD
[F]
Recommended Operating Conditions
Symbol Parameter Conditions Min. Typ. Max. Unit
I
QCCL
Quiescent V
CC
Supply
Current
V
CC
= 15 V
IN
(UL, VL, WL)
= 0 V
V
CC(L)
- COM - - 23 mA
I
QCCH
V
CC
= 15 V
IN
(UH, VH, WH)
= 0 V
V
CC(UH)
, V
CC(VH)
, V
CC(WH)
- COM
- - 100
A
I
QBS
Quiescent V
BS
Supply
Current
V
BS
= 15 V
IN
(UH, VH, WH)
= 0 V
V
B(U)
- V
S(U)
, V
B(V)
-V
S(V)
,
V
B(W)
- V
S(W)
- - 500 A
V
FOH
Fault Output Voltage V
SC
= 0 V, V
FO
Circuit: 4.7 k to 5 V Pull-up 4.5 - - V
V
FOL
V
SC
= 1 V, V
FO
Circuit: 4.7 k to 5 V Pull-up - - 0.8 V
V
SC(ref)
Short-Circuit Current Trip Level V
CC
= 15 V (2nd Note 4) 0.45 0.50 0.55 V
TSD Over-Temperature Protection Temperature at LVIC 125 145 175 °C
TSD Over-Temperature Protection
Hysterisis
Temperature at LVIC - 18 - °C
UV
CCD
Supply Circuit Under-Voltage
Protection
Detection Level 10.7 11.9 13.0 V
UV
CCR
Reset Level 11.2 12.4 13.2 V
UV
BSD
Detection Level 10.1 11.3 12.5 V
UV
BSR
Reset Level 10.5 11.7 12.9 V
t
FOD
Fault-Out Pulse Width C
FOD
= 33 nF (2nd Note 5) 1.0 1.8 - ms
V
IN(ON)
ON Threshold Voltage Applied between IN
(UH)
, IN
(VH)
, IN
(WH)
, IN
(UL)
,
IN
(VL)
, IN
(WL)
- COM
3.0 - - V
V
IN(OFF)
OFF Threshold Voltage - - 0.8 V
Symbol Parameter Conditions Min. Typ. Max. Unit
V
PN
Supply Voltage Applied between P - N
U
, N
V
, N
W
- 300 400 V
V
CC
Control Supply Voltage Applied between V
CC(UH)
, V
CC(VH)
, V
CC(WH)
,
V
CC(L)
- COM
13.5 - 16.5 V
V
BS
High-Side Bias Voltage Applied between V
B(U)
- V
S(U)
, V
B(V)
- V
S(V)
,
V
B(W)
- V
S(W)
13 - 18.5 V
dV
CC
/ dt,
dV
BS
/ dt
Control Supply Variation -1 - 1 V /
s
t
dead
Blanking Time for Preventing
Arm-Short
For Each Input Signal 2.5 - - s
f
PWM
PWM Input Signal -20C T
C
 100°C, -20C T
J
125°C - - 20 kHz
V
SEN
Voltage for Current Sensing Applied between N
U
, N
V
, N
W
- COM
(Including Surge Voltage)
-4 4 V