Datasheet

ManualsBrandsFAIRCHILD SEMICONDUCTOR ManualsBJTs & IGBTsIGBT

FSBB30CH60F Motion SPM® 3 Series

January 2014

FSBB30CH60F Rev. C6

FSBB30CH60F

Motion SPM

3 Series

Features

• UL Certified No. E209204 (UL1557)

• 600 V - 30 A 3-Phase IGBT Inverter with Integral Gate

Drivers and Protection

• Built-In Thermal Shutdown Function

• Low-Loss, Short-Circuit Rated IGBTs

• Very Low Thermal Resistance Using AlN DBC Sub-

strate

• Dedicated Vs Pins Simplify PCB Layout

• Separate Open-Emitter Pins from Low-Side IGBTs for

Three-Phase Current Sensing

• Single-Grounded Power Supply

• Isolation Rating: 2500 V

rms

/ min.

Applications

• Motion Control - Home Appliance / Industrial Motor

Related Resources

• AN-9035 - Motion SPM 3 Series Ver.2 User’s Guide

General Description

FSBB30CH60F is a Motion SPM

3 module providing a

fully-featured, high-performance inverter output stage

for AC Induction, BLDC, and PMSM motors. These mod-

ules integrate optimized gate drive of the built-in IGBTs

to minimize EMI and losses, while also providing multi-

ple on-module protection features including under-volt-

age lockouts, over-current shutdown, and fault reporting.

The built-in, high-speed HVIC requires only a single sup-

ply voltage and translates the incoming logic-level gate

inputs to the high-voltage, high-current drive signals

required to properly drive the module's internal IGBTs.

Separate negative IGBT terminals are available for each

phase to support the widest variety of control algorithms.

Package Marking and Ordering Information

Figure 1. Package Overview

Device Device Marking Package Packing Type Quantity

FSBB30CH60F FSBB30CH60F SPMEA-027 Rail 10

Summary of content (14 pages)

PAGE 1
FSBB30CH60F Motion SPM® 3 Series Features General Description • UL Certified No. E209204 (UL1557) FSBB30CH60F is a Motion SPM® 3 module providing a fully-featured, high-performance inverter output stage for AC Induction, BLDC, and PMSM motors. These modules integrate optimized gate drive of the built-in IGBTs to minimize EMI and losses, while also providing multiple on-module protection features including under-voltage lockouts, over-current shutdown, and fault reporting.
PAGE 2
FSBB30CH60F Motion SPM® 3 Series Integrated Power Functions • 600 V - 30 A IGBT inverter for three-phase DC / AC power conversion (please refer to Figure 3) Integrated Drive, Protection and System Control Functions • For inverter high-side IGBTs: gate drive circuit, high-voltage isolated high-speed level shifting control circuit Under-Voltage Lock-Out Protection (UVLO) Note: Available bootstrap circuit example is given in Figures 10 and 11.
PAGE 3
FSBB30CH60F Motion SPM® 3 Series Pin Descriptions Pin Number Pin Name 1 VCC(L) Pin Description Low-Side Common Bias Voltage for IC and IGBTs Driving 2 COM Common Supply Ground 3 IN(UL) Signal Input for Low-Side U-Phase 4 IN(VL) Signal Input for Low-Side V-Phase 5 IN(WL) Signal Input for Low-Side W-Phase Fault Output 6 VFO 7 CFOD Capacitor for Fault Output Duration Selection Capacitor (Low-pass Filter) for Short-Circuit Current Detection Input 8 CSC 9 IN(UH) 10 VCC(UH) 11 VB(U)
PAGE 4
FSBB30CH60F Motion SPM® 3 Series Internal Equivalent Circuit and Input/Output Pins P (27) (19) V B(W ) (18) V CC(W H) (17) IN (W H) VB VCC IN (20) V S(W ) (15) V B(V) (14) V CC(VH) W (26) VB VCC IN (16) V S(V) (11) V B(U) OUT VS V (25) VB (10) V CC(UH) VCC OUT COM (9) IN (UH) IN (12) V S(U) (8) C SC C(SC) (7) C FO D VS U (24) OUT(W L) C(FOD) (6) V FO N W (23) VFO (5) IN (W L) (3) IN (UL) VS COM (13) IN (VH) (4) IN (VL) OUT COM IN(W L) OUT(VL) IN(VL) N V (22) IN(UL)
PAGE 5
unless otherwise specified.
PAGE 6
Inverter Part Symbol VCE(SAT) VF HS tON Parameter Conditions Min. Typ. Max. Unit Collector - Emitter Saturation Voltage VCC = VBS = 15 V VIN = 5 V IC =30 A, TJ = 25°C - - 2.75 V FWDi Forward Voltage VIN = 0 V IC =30 A, TJ = 25°C - - 2.4 V Switching Times VPN = 300 V, VCC = VBS = 15 V IC = 30 A VIN = 0 V  5 V, Inductive Load (2nd Note 3) - 0.49 - s - 0.34 - s - 0.86 - s - 0.52 - s tC(ON) tOFF tC(OFF) - 0.10 - s - 0.68 - s - 0.47 - s - 0.
PAGE 7
Control Part Symbol IQCCL Parameter Conditions Quiescent VCC Supply Current IQCCH Min. Typ. Max. Unit VCC = 15 V IN(UL, VL, WL) = 0 V VCC(L) - COM - - 23 mA VCC = 15 V IN(UH, VH, WH) = 0 V VCC(UH), VCC(VH), VCC(WH) - COM - - 100 A VB(U) - VS(U), VB(V) -VS(V), VB(W) - VS(W) - - 500 A 4.5 - - V IQBS Quiescent VBS Supply Current VBS = 15 V IN(UH, VH, WH) = 0 V VFOH Fault Output Voltage VSC = 0 V, VFO Circuit: 4.7 k to 5 V Pull-up VSC = 1 V, VFO Circuit: 4.
PAGE 8
Parameter Mounting Torque Conditions Mounting Screw: M3 Device Flatness Min. Typ. Max. Unit 0.51 0.62 0.72 N•m 0 - +120 m - 15.00 - g Recommended 0.62 N•m See Figure 5 Weight (+) (+) Figure 5. Flatness Measurement Position ©2006 Fairchild Semiconductor Corporation FSBB30CH60F Rev. C6 8 www.fairchildsemi.
PAGE 9
FSBB30CH60F Motion SPM® 3 Series Time Charts of Protective Function Input Signal Protection Circuit State RESET SET RESET UVCCR a1 Control Supply Voltage a6 UVCCD a3 a2 a7 a4 Output Current a5 Fault Output Signal a1 : Control supply voltage rises: after the voltage rises UVCCR, the circuits start to operate when next input is applied. a2 : Normal operation: IGBT ON and carrying current. a3 : Under-Voltage detection (UVCCD). a4 : IGBT OFF in spite of control input condition.
PAGE 10
c6 Protection Circuit State SET Internal IGBT Gate - Emitter Voltage FSBB30CH60F Motion SPM® 3 Series Lower Arms Control Input c7 RESET c4 c3 c2 SC c1 c8 Output Current SC Reference Voltage Sensing Voltage of Shunt Resistance Fault Output Signal c5 CR Circuit Time Constant Delay (with the external shunt resistance and CR connection) c1 : Normal operation: IGBT ON and carrying current. c2 : Short-Circuit current detection (SC trigger). c3 : Hard IGBT gate interrupt. c4 : IGBT turns OFF.
PAGE 11
FSBB30CH60F Motion SPM® 3 Series +5 V SPM RPF = 4.7 k IN(UH) , IN(VH) , IN(WH) MCU IN (UL) , IN (VL) , IN(WL) 100  1 nF VFO CPF= 1 nF COM Figure 9. Recommended MCU I/O Interface Circuit 3rd Notes: 1. RC coupling at each input (parts shown dotted) might change depending on the PWM control scheme in the application and the wiring impedance of the application’s printed circuit board. The Motion SPM® 3 Product input signal section integrates a 3.3 k(typ.) pull-down resistor.
PAGE 12
RE(VH) +15 V RE(UH) RBS DBS (19) VB(W) (18) VCC(WH) CBS Gating WH CBSC (17) IN(WH) (20) VS(W) RBS DBS P (27) VB VCC OUT COM IN (15) VB(V) (14) VCC(VH) VB VCC CBS Gating VH CBSC (13) IN(VH) (16) VS(V) M C U RBS DBS (11) VB(U) (10) VCC(UH) CBS Gating UH W (26) VS CBSC (9) IN(UH) (12) VS(U) OUT COM IN VS V (25) M VB VCC CDCS OUT COM IN Vdc U (24) VS RF +5 V (8) CSC CSC RPF (7) CFOD RS CFOD Fault (6) VFO (5) IN(WL) Gating WL C(SC) OUT(WL) C(FOD) NW (23) IN(WL)
PAGE 13
FSBB30CH60F Motion SPM® 3 Series Detailed Package Outline Drawings Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or data on the drawing and contact a FairchildSemiconductor representative to verify or obtain the most recent revision.
PAGE 14
FSBB30CH60F Motion SPM® 3 Series ©2006 Fairchild Semiconductor Corporation FSBB30CH60F Rev. C6 14 www.fairchildsemi.