Datasheet

ManualsBrandsFAIRCHILD SEMICONDUCTOR ManualsBJTs & IGBTsIGBT

FPDB30PH60 PFC SPM® 3 Series for 2-Phase Bridgeless PFC

December 2013

FPDB30PH60 Rev. C3

FPDB30PH60

PFC SPM

3 Series for 2-Phase Bridgeless PFC

Features

• UL Certified No. E209204 (UL1557)

• 600 V - 30 A 2-Phase Bridgeless PFC with Integral

Gate Driver and Protection

• Very Low Thermal Resistance Using Al

DBC

Substrate

• Built-in NTC Thermistor for Temperature Monitoring

• Built-in Shunt Resistor for Current Sensing

• Optimized for 20kHz Switching Frequency

• Isolation Rating: 2500 Vrms/min.

Applications

• 2-Phase Bridgeless PFC Converter

Related Source

• AN-9041 - Bridgeless PFC SPM 3 Series Design

Guide

General Description

The FPDB30PH60 is a PFC SPM

3 module providing a

fully-featured, high-performance Bridgeless PFC (Power

Factor Correction) input power stage for consumer,

medical, and industrial applications. These modules

integrate optimized gate drive of the built-in IGBTs to

minimize EMI and losses, while also

providing multiple on-module protection features

including under-voltage lockout, over-current shutdown,

thermal monitoring, and fault reporting. These modules

also feature high-performance output diodes and shunt

resistor for additional space savings and mounting

convenience.

Figure 1. Package Overview

Package Marking & Ordering Information

Device Device Marking Package Packing Type Quantity

FPDB30PH60 FPDB30PH60 SPMGA-027 Rail 10

Summary of content (11 pages)

PAGE 1
FPDB30PH60 PFC SPM® 3 Series for 2-Phase Bridgeless PFC Features General Description The FPDB30PH60 is a PFC SPM® 3 module providing a fully-featured, high-performance Bridgeless PFC (Power Factor Correction) input power stage for consumer, medical, and industrial applications.
PAGE 2
• PFC converter for single-phase AC / DC power conversion.(please refer to Figure 3) Integrated Drive, Protection and System Control Functions • For IGBTs: gate drive circuit, Over-Current Protection (OCP), control supply circuit Under-Voltage Lock-Out (UVLO) Protection • Fault signal: corresponding to OC and UV fault • Built-in thermistor: temperature monitoring • Input interface: active-HIGH interface, works with 3.
PAGE 3
FPDB30PH60 PFC SPM® 3 Series for 2-Phase Bridgeless PFC Pin Descriptions Pin Number Pin Name Pin Description 1 VCC Common Bias Voltage for IC and IGBTs Driving 2 COM Common Supply Ground 4 IN(R) Signal Input for Low-Side R-Phase IGBT 5 IN(S) Signal Input for Low-Side S-Phase IGBT 6 VFO Fault Output 7 CFOD Capacitor for Fault Output Duration Selection 8 CSC Capacitor(Low-Pass Filter) for Over-Current Detection 19 R(TH) Series Resistor for The Use of Thermistor 20 V(TH) Thermisto
PAGE 4
unless otherwise specified.
PAGE 5
Converter Part Symbol Item Condition Min. Typ. Max. Unit VCE(SAT) IGBT Saturation Voltage VCC = 15 V, VIN = 5 V, IC =30 A - 2.4 3.1 V VFH High-Side Diode Voltage IF = 30 A - 1.9 2.5 V VFL Low-Side Diode Voltage IF = 30 A - 1.2 1.6 V tON Switching Times VPN = 400 V, VCC = 15 V, IC =30 A VIN = 0 V  5 V, Inductive Load - 550 - ns - 200 - ns - 430 - ns tC(OFF) - 180 - ns trr - 60 - ns Irr - 6 - A 1.8 2.0 2.
PAGE 6
Symbol Item Condition IQCCL Quiescent VCC Supply Current VCC = 15 V, IN = 0 V VCC - COM VFOH Fault Output Voltage VFOL Min. Typ. Max. Unit - - 26 mA VSC = 0 V, VFO Circuit: 4.7 k to 5 V Pull-up 4.5 - - V VSC = 1 V, VFO Circuit: 4.7 k to 5 V Pull-up - - 0.8 V VSC(ref) Over-Current Trip Level VCC = 15 V 0.45 0.50 0.55 V UVCCD Supply Circuit Under-Voltage Protection Detection Level 10.7 11.9 13.0 V Reset Level 11.2 12.4 13.
PAGE 7
Item Condition Mounting Torque Mounting Screw: M3 Device Flatness See Figure 6 Recommended 0.62 N•m Weight Min. Typ. Max. Units 0.51 0.62 0.72 N•m 0 - +120 m - 15.00 - g (+) (+) (+) Figure 6. Flatness Measurement Position ©2005 Fairchild Semiconductor Corporation FPDB30PH60 Rev. C3 7 www.fairchildsemi.
PAGE 8
FPDB30PH60 PFC SPM® 3 Series for 2-Phase Bridgeless PFC Time Charts of Protective Function In p u t S ig n a l In te rn a l IG B T G a te -E m itte r V o lta g e P3 UV re se t P5 C o n tro l S u p p ly V o lta g e P2 UV d e te c t P6 P1 O u tp u t C u rre n t P4 F a u lt O u tp u t S ig n a l P1 : Normal operation: IGBT ON and conducting current. P2 : Under-voltage detection. P3 : IGBT gate interrupt. P4 : Fault signal generation. P5 : Under-voltage reset.
PAGE 9
+5 V VTH RTH CSC MCU CFOD VFO or Controller IN(S) IN(R) NTC Thermistor PR S CSC R CFOD 3-Phase Inverter VFO IN(S) OUT(S) IN(R) COM COM N OUT(R) Shunt Resistor VCC NSENSE VAC- VCC Figure 9. Application Example Notes: 6. For the over-current protection, please set time constant in the range 3 ~ 4 s. ©2005 Fairchild Semiconductor Corporation FPDB30PH60 Rev. C3 9 www.fairchildsemi.
PAGE 10
FPDB30PH60 PFC SPM® 3 Series for 2-Phase Bridgeless PFC Detailed Package Outline Drawings Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or data on the drawing and contact a FairchildSemiconductor representative to verify or obtain the most recent revision.
PAGE 11
FPDB30PH60 PFC SPM® 3 Series for 2-Phase Bridgeless PFC ©2005 Fairchild Semiconductor Corporation FPDB30PH60 Rev. C3 11 www.fairchildsemi.