Datasheet

ManualsBrandsFAIRCHILD SEMICONDUCTOR ManualsLogic ICsLogic IC - Inverter Inverter 74LCX TSSOP 14

74LCX04 — Low Voltage Hex Inverter with 5V Tolerant Inputs

74LCX04 Rev. 1.6.1

74LCX04

Low Voltage Hex Inverter with 5V Tolerant Inputs

Features

■

5V tolerant inputs

■

2.3V–3.6V V

specifications provided

■

5.2ns t

max. (V

3.3V), 10µA I

max.

■

Power down high impedance inputs and outputs

■

±24mA output drive (V

3.0V)

■

Latch-up performance exceeds JEDEC 78 conditions

■

ESD performance:

– Human body model

2000V

– Machine model

200V

■

Leadless DQFN package

General Description

The LCX04 contains six inverters. The inputs tolerate

voltages up to 7V allowing the interface of 5V systems to

3V systems.

The 74LCX04 is fabricated with advanced CMOS tech-

nology to achieve high speed operation while maintain-

ing CMOS low power dissipation.

Ordering Information

Note:

1. DQFN package available in Tape and Reel only.

Device also available in Tape and Reel. Specify by appending suffix letter “X” to the ordering number.

All packages are lead free per JEDEC: J-STD-020B standard.

Order Number

Package

Number Package Description

74LCX04M M14A 14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-012, 0.150" Narrow

74LCX04SJ M14D 14-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide

74LCX04BQX

(1)

MLP14A 14-Terminal Depopulated Quad Very-Thin Flat Pack No Leads (DQFN), JEDEC

MO-241, 2.5 x 3.0mm

74LCX04MTC MTC14 14-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm

Wide

Implements

proprietary

noise/EMI reduction circuitry

December 2013

Summary of content (13 pages)

PAGE 1
74LCX04 Low Voltage Hex Inverter with 5V Tolerant Inputs Features General Description ■ 5V tolerant inputs The LCX04 contains six inverters. The inputs tolerate voltages up to 7V allowing the interface of 5V systems to 3V systems. ■ 2.3V–3.6V VCC specifications provided ■ 5.2ns tPD max. (VCC = 3.3V), 10µA ICC max. ■ Power down high impedance inputs and outputs ■ ±24mA output drive (VCC = 3.
PAGE 2
74LCX04 — Low Voltage Hex Inverter with 5V Tolerant Inputs Connection Diagrams Logic Symbol Pin Assignments for SOIC, SOP, and TSSOP IEEE/IEC Pad Assignments for DQFN (Top View) (Bottom View) Pin Description Pin Names Description An, Bn Inputs On Outputs DAP No Connect Note: DAP (Die Attach Pad) ©1995 Fairchild Semiconductor Corporation 74LCX04 Rev. 1.6.1 www.fairchildsemi.
PAGE 3
Symbol VCC VI VO Parameter Rating Supply Voltage –0.5V to +7.0V DC Input Voltage –0.5V to +7.0V DC Output Voltage, Output in HIGH or LOW IIK DC Input Diode Current, VI < GND IOK DC Output Diode Current State(2) –0.5V to VCC + 0.5V –50mA VO < GND –50mA VO > VCC +50mA IO DC Output Source/Sink Current ICC DC Supply Current per Supply Pin IGND DC Ground Current per Ground Pin TSTG Storage Temperature ±50mA ±100mA ±100mA –65°C to +150°C Note: 2.
PAGE 4
TA = –40°C to +85°C Symbol VIH VIL VOH VOL II Parameter HIGH Level Input Voltage LOW Level Input Voltage HIGH Level Output Voltage LOW Level Output Voltage Input Leakage Current VCC (V) Min. 2.3–2.7 1.7 2.7–3.6 2.0 Max. 2.3–2.7 0.7 0.8 IOH = –100µA 2.3–3.6 V VCC – 0.2 2.3 IOH = –8mA 1.8 2.7 IOH = –12mA 2.2 3.0 IOH = –18mA 2.4 IOH = –24mA 2.2 V IOL = 100µA 0.2 2.3 IOL = 8mA 0.6 2.7 IOL = 12mA 0.4 3.0 IOL = 16mA 0.4 IOL = 24mA 0.55 0 ≤ VI ≤ 5.5V 2.3–3.6 2.3–3.
PAGE 5
TA = 25°C Symbol Parameter VCC (V) VOLP Quiet Output Dynamic Peak VOL 3.3 2.5 VOLV Quiet Output Dynamic Valley VOL Conditions Typical Unit CL = 50pF, VIH = 3.3V, VIL = 0V 0.8 V CL = 30pF, VIH = 2.5V, VIL = 0V 0.6 3.3 CL = 50 pF, VIH = 3.3V, VIL = 0V –0.8 2.5 CL = 30 pF, VIH = 2.5V, VIL = 0V –0.6 V Capacitance Symbol Typical Units Input Capacitance VCC = Open, VI = 0V or VCC 7 pF COUT Output Capacitance VCC = 3.
PAGE 6
Test Switch tPLH, tPHL Open tPZL, tPLZ 6V at VCC = 3.3 ± 0.3V VCC x 2 at VCC = 2.5 ± 0.2V tPZH, tPHZ GND Figure 1. AC Test Circuit (CL includes probe and jig capacitance) Waveform for Inverting and Non-Inverting Functions 3-STATE Output High Enable and Disable Times for Logic Propagation Delay. Pulse Width and trec Waveforms Setup Time, Hold Time and Recovery Time for Logic 3-STATE Output Low Enable and Disable Times for Logic trise and tfall VCC Symbol 3.3V ± 0.3V 2.7V 2.5V ± 0.
PAGE 7
4LCX04 — Low Voltage Hex Inverter with 5V Tolerant Inputs Schematic Diagram (Generic for LCX Family) ©1995 Fairchild Semiconductor Corporation 74LCX04 Rev. 1.6.1 www.fairchildsemi.
PAGE 8
Tape Format for DQFN Package Designator Tape Section Number of Cavities Cavity Status Cover Tape Status BQX Leader (Start End) 125 (Typ.) Empty Sealed Carrier 3000 Filled Sealed Trailer (Hub End) 75 (Typ.) Empty Sealed Tape Dimensions inches (millimeters) Reel Dimensions inches (millimeters) Tape Size A B C D N W1 W2 12mm 13.0 (330.0) 0.059 (1.50) 0.512 (13.00) 0.795 (20.20) 2.165 (55.00) 0.488 (12.4) 0.724 (18.4) ©1995 Fairchild Semiconductor Corporation 74LCX04 Rev. 1.
PAGE 9
74LCX04 — Low Voltage Hex Inverter with 5V Tolerant Inputs Physical Dimensions 8.75 8.50 0.65 A 7.62 14 8 B 5.60 4.00 3.80 6.00 PIN ONE INDICATOR 1 1.70 7 0.51 0.35 1.27 0.25 1.27 LAND PATTERN RECOMMENDATION M C B A (0.33) 1.75 MAX 1.50 1.25 SEE DETAIL A 0.25 0.10 C 0.25 0.19 0.10 C NOTES: UNLESS OTHERWISE SPECIFIED A) THIS PACKAGE CONFORMS TO JEDEC MS-012, VARIATION AB, ISSUE C, B) ALL DIMENSIONS ARE IN MILLIMETERS. C) DIMENSIONS DO NOT INCLUDE MOLD GAGE PLANE FLASH OR BURRS.
PAGE 10
74LCX04 — Low Voltage Hex Inverter with 5V Tolerant Inputs Physical Dimensions (Continued) Figure 4. 14-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision.
PAGE 11
74LCX04 — Low Voltage Hex Inverter with 5V Tolerant Inputs Physical Dimensions (Continued) Figure 5. 14-Terminal Depopulated Quad Very-Thin Flat Pack No Leads (DQFN), JEDEC MO-241, 2.5 x 3.0mm Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision.
PAGE 12
0.65 0.43 TYP 1.65 6.10 0.45 12.00° TOP & BOTTOM R0.09 min A. CONFORMS TO JEDEC REGISTRATION MO-153, VARIATION AB, REF NOTE 6 B. DIMENSIONS ARE IN MILLIMETERS C. DIMENSIONS ARE EXCLUSIVE OF BURRS, MOLD FLASH, AND TIE BAR EXTRUSIONS D. DIMENSIONING AND TOLERANCES PER ANSI Y14.5M, 1982 E. LANDPATTERN STANDARD: SOP65P640X110-14M F. DRAWING FILE NAME: MTC14REV6 1.00 R0.09min Figure 6. 14-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.
PAGE 13
TRADEMARKS The following includes registered and unregistered trademarks and service marks, owned by Fairchild Semiconductor and/or its global subsidiaries, and is not intended to be an exhaustive list of all such trademarks.