Installation Instructions / Warranty Massaud 18010001 Massaud 18210001
Axor Massaud Single-Control Lavatory Faucet 18010001 Axor Massaud Single-Control Bidet Faucet 18210001 18010001 Do not allow the supply hoses to bend or twist! 18210001
Product Specification Max. Flow Rate 2.2 gpm Max. incoming water pressure 145 psi Recommended water pressure 14.5 - 72 psi Max. hot water temperature 176o F* Recommended hot water temp 120oF - 140oF* Hole size in mounting surface 18010001 1 1/4” 18210001 1 3/8” Max. mounting surface thickness 1 5/8” Model 18010001 has 10 mm supply hoses -- 10 mm - 3/8” adapters included. No drain or pull rod is included with model 18010001. Grid drain 06400000 (not included) is recommended.
Slide the compression nut, cone washer, metal washer, and rubber washer over the end of the supply hose. Place the supply hose in the filter. Tighten the compression nut to the filter, using two wrenches, as shown in the diagram, to prevent the supply hose from twisting. 18210001 only: Secure the supply hoses to the stops with 3/8” compression fittings (not included). Use two wrenches, as shown, to keep the hoses from twisting. Turn on the water and check all connections for leaks.
Install the pop-up drain (18210001 only) Remove the plunger assembly. Unscrew the drain outlet flange from the tee. plunger Unscrew the tailpiece from the tee. Wrap the threads with plumbers’ thread tape and replace. height adjuster Install the white, flexible sealing gasket to the flange. Place it in the sink outlet. flange From under the sink, install the black mack gasket, white friction ring and retainer nut to the flange. Do not tighten the nut against the bottom of the sink at this time.
User Instructions Pivot the handle upward to turn the water on, downward to turn the water off. Pivot the handle to the rear for warmer water, to the front for cooler water. 18010001 only: If the flow of water decreases over time, remove and clean the filter screen.
Replacement Parts 10 2 13 11 1 5 4 15 3 9 6 12 14 8 7 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 spout diffuser handle nut cartridge flange drain fixing set supply hose cover ball joint aerator pull rod fixing set supply hose 98649000 97444000 18093000 97157000 96339000 98650000 96139000 96078000 96321000 98651000 97362000 97360000 97158000 13961000 96321001
Cleaning Recommendation for Hansgrohe Products Modern sanitary faucetry and shower fixtures consist of very different materials to comply with the needs of the market with regard to design and functionality. To avoid damage and returns, it is necessary to consider certain points when cleaning: Cleaning materials for faucets and shower products: Acids are necessary ingredients of cleaning materials for removing lime.
Limited Lifetime Consumer Warranty This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe”). This warranty is limited to Hansgrohe products which are purchased by a consumer in the United States after March 1, 1996, and installed in either the United States or Canada. WHO IS COVERED BY THE WARRANTY This warranty extends to the original consumer purchaser only. This warranty is non-transferable.
EXCLUSIONS AND LIMITATIONS REPAIR OR REPLACEMENT (OR, IN LIMITED CIRCUMSTANCES, REFUND OF THE PURCHASE PRICE) AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER. HANSGROHE NEITHER ASSUMES NOR AUTHORIZES ANY PERSON TO CREATE FOR IT ANY OBLIGATION OR LIABILITY IN CONNECTION WITH THIS PRODUCT.
www.hansgrohe-USA.com US - Installation Instructions • Part No. 90406821 • Revised 04/2007 Hansgrohe, Inc. • 1490 Bluegrass Lakes Parkway • Alpharetta, GA 30004 Tel.
