Installation Instructions / Warranty Starck 10101XX1 10140XX1 Starck 10106XX1 10145XX1 Starck X 10170001 10175001 10180001 10185001
Starck 10101XX1/10106XX1 Starck 10140XX1/10145XX1 Starck X 10170001/10175001 Starck X 10180001/10185001
Starck 10101XX1/10106XX1/10140XX1/10145XX1 Starck X 10170001/10175001/10180001/10185001 Do not install this faucet on a sink with a raised lip. ok! no! Technical Information Recommended water pressure Max. water pressure Max. hot water temp. Recommended hot water temp. Flow rate Battery Automatic shutoff 15 - 58 psi 58 psi 176oF* 120oF - 140oF* 1.3 gpm CR-P2 / 6 V Lithium after 1 minute *Please know and follow all local plumbing codes when setting the temperature on the water heater.
Installation notes • Flush the hot and cold supplies thoroughly before installing the faucet. Damage to the faucet caused by debris is not covered under the warranty. • The hot and cold supplies should be of equal pressure. • The distance between the switch on/off point to the faucet is approx. 6 1/4” - 8” under normal conditions. The detection area may be less for dark, non-reflective objects, or greater for bright, highly reflective objects. • Do not install the faucet on a sink with a raised edge.
Installation Position the faucet on the sink or countertop (1). Install and tighten the mounting nut (2). Tighten the tensioning screws (3). Connect the 3/8” adapters to the stops (4). Connect the hoses to the adapters (5). Tighten the hoses with two wrenches, as shown, to prevent the hoses from twisting.
Connect the faucet power cable to the battery pack or AC power pack (1). Plug the AC power pack in. Turn the hot and cold supplies on (2). Remove the protective film from the sensor window (3). Wait 30 seconds before attempting to use the faucet (4). Position your hand in front of the sensor to turn the water on. Due to air in the faucet, the spray pattern may be unattractive for the first 10 - 15 uses after installation or service.
Remove the faucet body (1). Turn the temperature screw forward to make the water cooler, backward to make it warmer (2). Dry any drops of water from the faucet or mounting surface. Replace the faucet body (1). Replace the screw (2). Turn the water supplies on (3). Reconnect the power cable (4). Wait 30 seconds (1). Place your hand in front of the faucet to turn it on (2).
Battery Replacement -- models 10101XX1/ 10106XX1/10170001/10175001 only If the LED in the sensor window flashes, the battery is low, but the faucet can still be used. If the LED lights continuously, the battery must be changed before the faucet can be used. Remove the four screws and the battery pack cover. Remove the old battery (1). Install the new battery (2). Reinstall the battery pack cover. Wait 30 seconds (1). Activate the faucet by placing a hand in front of the sensor (2).
Clean the aerator and filters -- all models If the water flow is reduced over time, clean the aerator (a) and the filters (b). Turn the water supplies off (1). Disconnect the power cable (2). Starck 10101/10106/10140/10145 -- unscrew and remove the aerator (a). Starck X 10170/10175/10180/10185 -- remove the spray former (a), using a 2 mm Allen wrench to loosen the screws. Do not lose the screws! All models -- disconnect the hot and cold supply hoses from the adapters. Remove the filters (b).
Turn the water on (1). Reconnect the power cable (2). Wait 30 seconds (1). Place a hand in front of the sensor to turn the faucet on (2).
Cleaning The faucet may be turned off temporarily so that the sink may be cleaned. Cover the sensor window with a hand for approximately 10 seconds. The faucet will turn off for approximately 60 seconds, so that the sink may be cleaned. The LED in the sensor window will flash. When the LED no longer flashes, the faucet may be used normally.
Change the Spray Former -- Starck X 10170 / 10175 / 10180 / 10185 only The waterfall spray former is installed on the faucet at the factory. A round monospray spray former is included with the faucet. The spray former may be changed easily, if desired. Use a 2 mm Allen wrench to remove the spray former screws. Remove the old spray former. Install the new spray former. Tighten the screws.
Reduce the Sensor Range The sensor is set for maximum range at the factory. If the faucet is used on a very small or highly reflective lavatory, the sensor range may be reduced by approximately 2”. Disconnect the power cable for approximately 10 seconds (1). Reconnect the power cable (2). The LED will blink once to indicate that it is in the “maximum range” mode. When the LED stays on, cover the sensor window with your hand or with a white card for 20 - 40 seconds to reset the electronics*.
Replacement Parts 4 3 6 1 10 5 2 8 9 7 1 2 3 4 5 6 7 8 9 10 14 battery, lithium CR-P2 / 6V connection hose 98809000 spray former 98867000 aerator, Starck 94005XX0 fixing set 13961000 electronics, Starck 98799000 electronics, Starck X 98849000 AC adapter battery box 98801000 check valve 96456000 aerator, Starck X 98610000 XX = color 00 = chrome 80 = Steel Maintenance note: the check valves (item #9) should be removed and checked yearly.
Cleaning Recommendation for Hansgrohe Products Modern lavatory faucets, kitchen faucets, and showers consist of very different materials to comply with the needs of the market with regard to design and functionality. To avoid damage and returns, it is necessary to consider certain criteria when cleaning.
including, without limitation, a commercial purpose, this warranty extends only (i) for 1 year, with respect to Hansgrohe and Commercial products, and (ii) for 5 years, with respect to AXOR products. THIS WARRANTY DOES NOT COVER, AND HANSGROHE WILL NOT PAY FOR: A. Conditions, malfunctions or damage not resulting from defects in material or workmanship. B.
