Installation Instructions / Warranty 3-Hole Roman Tub Rough 3-Hole Roman Tub Trim Kits
3-Hole Roman Tub Rough 06607000 Technical Specification Recommended operating pressure 45 - 80 psi Recommended hot water temp. 120o - 140o F* Max. flow rate 10 gpm Hole sizes valves 1 1/4” spout 1 3/8” spout pin 3/16” Max. mounting surface thickness 1 9/16” Requires 1/2” supply lines (not included) *Please know and follow all applicable local plumbing codes when setting the temperature on the water heater. In Massachusetts, the water heater may be set no higher than 112oF.
Installation Install the connecting tubes: Place a compression nut and ferrule on one end of the connection tube. Push the tube into the inlet of the spout tee. Tighten the compression nut. Place another compression nut and ferrule on the other end of the compression tube. Push the tube into the outlet port of the valve. Tighten the compression nut. Repeat with the second connection tube. Install the rough: Remove the plaster shields, escutcheon adapters, o-rings, and stop rings from the valves.
Interaktiv and Retroaktiv Trim, 3-Hole Roman Tub Sets Models Covered Interaktiv Solaris Stratos Metro Interaktiv S 06630XX0 06574XX0 06551000 06875000 Retroaktiv Cross handle Scroll handle Lever handle Swing 06122XX0 06120XX0 06120XX0 Tango 06045XX0 06044XX0 06043XX0 Limbo 06109XX0 06108XX0 06107XX0 These trim kits are for use with rough 06607000. The rough must be installed, and the mounting surface complete and watertight.
Retroaktiv Tango (scroll handles shown) Retroaktiv Limbo (lever handles shown)
Install the Handles Retroaktiv only: Install the deco-rings on the handles. All models: Remove the plaster shields from the hot and cold valves and spout tee. Position the handle over the sten with the lever in the desired “off” position. While holding the lever with one hand, use the other hand to turn the bell, and screw it down over the valve. Install the spout: Retroaktiv Swing only: Install the deco-ring on the spout.
Push the spout sealing ring firmly into the spout tee. Press the spout over the spout tee. Install and tighten the set screw with the enclosed 3 mm Allen wrench. Turn on the water and check all connections for leaks. User Instructions: Turn the left handle to obtain hot water, the right handle to obtain cold water. If the flow of water diminishes over time, remove and clean the aerator.
Replacement Parts 6 4 2 3 1 5 06607000 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 hot cartridge cold cartridge mounting kit mounting kit compression ftg valve set sealing ring aerator set screw Solaris handles Stratos handles Metro handles Interaktiv S handles cross handles, tall scroll handles, tall lever handles, tall cross handles, low scroll handles, low lever handles, low handle deco ring Interaktiv 9 10 8 7 11 12 13 94009000 94008000 88511000 88540000 88513000 88503000 8851200
Retroaktiv 14 9 8 15 7 20 16 Swing 9 8 7 20 Tango Limbo 17 9 18 20 7 19 8
Cleaning Recommendation for Hansgrohe Products Modern sanitary faucetry and shower fixtures consist of very different materials to comply with the needs of the market with regard to design and functionality. To avoid damage and returns, it is necessary to consider certain points when cleaning: Cleaning materials for faucets and shower products: Acids are necessary ingredients of cleaning materials for removing lime.
year, with respect to Interaktiv and Retroaktiv products, and (ii) for 5 years, with respect to AXOR, ShowerPower and Pharo products. THIS WARRANTY DOES NOT COVER, AND HANSGROHE WILL NOT PAY FOR: A. Conditions, malfunctions or damage not resulting from defects in material or workmanship. B.
www.hansgrohe-USA.com US - Installation Instructions • Part No. 90964701 • Revised 01/2007 Hansgrohe, Inc. • 1490 Bluegrass Lakes Parkway • Alpharetta, GA 30004 Tel.
