Quick Installation Guide

+1.8VDC
Dimensional drawing(unit: mm)
Recognizable positon
Port description
Installation instructions
Installation Method 1
1. Remove the bracket from the main device and fix it at the electrical switch box
with 2 screws (M4*40) on the wall.
2. Mount the device, starting from top to bottom, onto the bracket.
3. Use an Allen key to tighten the device and the bracket from the top of the
device with 2 set screws (M3*10) to complete the installation.
Installation Method 2
1.Choose an appropriate mounting location and affix the positioning sticker to
the mounting location.
2.Create holes in the mounting location, at the positions marked by hole 5 and
hole 6 on the positioning sticker. (Recommended aperture: 6mm, Depth: 40mm)
3.Remove the positioning sticker.
4.Remove the bracket from the main device and fix it on the wall with 2 sets of
expansion bolts(M4*25).
5.Mount the device, starting from top to bottom, onto the bracket.
6 .Use an Allen key to tighten the device and the bracket from the top of the
device with 2 set screws (M3*10) to complete the installation.
Note:
2.Depending on your mounting location, select the appropriate holes on the
positioning sticker to mount the device onto the electrical wall switch box.
3.When installing, please use the screws provided in the accessories of the
product to prevent the bracket from not being installed tightly with the device.
Quick installation guide
Height range
Person to wall camera
distance W (cm)
60
130
140
150
80-200
90-210
100-220
Note:The recognizable height L is proportional to the camera to ground
distance H.
Specification
Product packing list
Liveness Detection
Verification Method
Recognition Speed
User Capacity
Operating System
Camera
Display
Multi touch
Tamper alarm
Operating temperature
Relative Humidity
Dimensions
Power Supply
Support
1:1, 1:N, 1:1/1:N
0.3s/person (1:N mode)
Up to 100000 users
Android 8.1
Dual wide-angle camera (RGB+NIR)
8-inch LCD touch display
Support
Support
-10°C ~ 55°C
5% to 95% noncondensing
119.6*214*25mm
DC 12V 2A
Support 2.4 GHz/5 GHz，IEEE 802.11a/g/b/n;
Wi-Fi
Bluetooth
Ethernet
Support
Support
Support Bluetooth 4.1+BLE
RS485*1, Wiegand TX*1, Wiegand RX*1, Dry contact*1,
RJ45*1, Alarm interface*3
Power button
IPhysical interface
Communication Method
Device
Screw
Set screws
Expansion bolt
Terminal
Terminal
Positioning sticker
Quick installation guide
M4*40
M3*10
M4*25
6Pin
5Pin
Product and accessory descriptionNo. Specification Quantity
Screw(for stand) M4*20
1
2
3
4
5
6
7
8
10
11
12
Allen key M3
Product warranty booklet
Device
Bracket
M3*10 Set screws
18
214
119.6
25
Camera to ground
distance H (cm)
Recognizable
height L (cm)
1.Use an Allen key to uncrew the two set screws from the top of the main device to
remove the bracket.
Water-proof gasket9
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause
undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator& your body.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit di�erent from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC Warning:
WIFI 2.4G B/G/N
WIFI 5G -5.8G band 1/2/3/4
Remark：This product can be used across EU member statesWe declares that this
device is in compliance with the essential requeirements and other relevant rovisions
of Directive 2014/53/EU.Our product do not contains the AC/DC apter.You need
purchase the DC 12V/2A compliance the directive 2014/30/EU.
The adapter shall be installed near the equipment and shall be easily accessible.