Instructions / Assembly

#10-14 410 STAINLESS STEEL***
• Use with 26 gauge or thinner to
avoid pre-drilling
• Available in 1", 1½", and 2"
• 1/4" hex head, EPDM/metal washer
• Use with steel panels installed on
treated lumber
• Use with aluminum
#9-16 300 SERIES
STAINLESS STEEL***
• Use for high corrosive environments
• Use with ALUMINUM panels
• Available in 1", 1½", and 2"
• 1/4" hex head, EPDM/metal washer
• Use with treated lumber
RIDGE CAP VENT
• Factory applied to the ridge cap
• Save up to half of your installation time
• Non-prole specic material
• Clean, dust free installation
• Virtually NO WASTED material
• 1½" x 3" material provides 17 sq.
inches/lineal foot free area at the ridge
RV35 AND RV100
• 10' metal ridge vent
• Variety of colors available
LP2 RIDGE VENT
• Available in Horizon S,
Grandrib 3 and Mighti-Rib proles
• Lower, custom-t prole
• Moisture and pest barrier
• Non-obtrusive appearance
• Reduces utility costs
• One-person installation
PROFILE FIT VENT-ROLL
• Available in Grandrib 3, 5V and SSR
• 10.66 sq. in. per lineal ft. of ridge
(5.33 / side)
#10-1 PANCAKE HEAD**
• Use with 1½" SSR and concealed
fastener panels
• Check with engineering department
for spacing with OSB or ½" plywood
#10-16 ULTIMATE WOODTITE**
• Use with ALL panels
• Available in 1", 1½", 2", 2 ½"
and 3"
• 5/16" case zinc hex head
• Hex head & washer all one piece
#10-12 WAFER HEAD**
• Use with Horizon S panel
• Check with engineering department
for spacing with OSB or ½" plywood
• Available in 1", 1½" , 2" and self
drillers
• Available with square drive head
#12x3/4" STITCH*
• Use for trim attachment for Horizon S
• 1/4" hex head, EPDM/metal washer
SYSTEM COMPONENTS 20
SEALANT
• Waterproof sealant to ll gaps up to 1"
• UV-resistant
• Permanent exibility - won’t crack
• Standard color: Gray (stocked)
• Up to 50 additional color options (non stocked)
SEALANT TAPE
• 3/16" x ½" x 40' (sidelap)
• 3/32" x ½" x 50' (endlap)
• 1/8" x 2" x 30'
SEALANT STRIP
•Use at valleys and hips
•1" x 1" x 19' 6.8" long
• Accommodates
up to 4 rails of
protection
• Customized rail
tubing
• Functions below
the standing seams
• Easy to retrot to
existing roofs
• Available in mill nished aluminum
and black e-coat primer
• Three sizes available to accommodate
differing seam widths
• Use on Fabral 1½" SSR panel
• Available in mill nished aluminum,
mill nished bronze, black e-coat
primer or custom colors
• Two sizes to accommodate differing
seam widths
• Use on Fabral 1½" SSR and Horizon S panels
• Dual rail, low
prole snow reten-
tion systems
• Stronger, lighter
system
• Receptor slot for
custom orna-
mental attachment
• Single rail, low-
prole snow
retention systems
• Functions below
the standing seams
• Economical
snow rail
• Easy to retrot to
existing roofs
F-RAIL E-RAIL S-RAIL
STANDING SEAM
SL1 SNOW MEISTER SNOW GUARD
AP SNOW GUARD
SL1 AP