Concept Remote Blower Instruction Manual READ AND SAVE THESE INSTRUCTIONS The Installer must leave these instructions with the homeowner. The homeowner must keep these instructions for future reference and for local electrical inspectors’ use.
CONTENTS 2 WARNING 3 CHARACTERISTICS 5 INSTALLATION 8 USE 13 MAINTENANCE 14 EN
READ THESE INSTRUCTIONS BEFORE YOU START INSTALLING THIS RANGEHOOD READ AND SAVE THESE INSTRUCTIONS WARNING: - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium setting. Always turn hood ON when cooking at high heat or when flambeing food (i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambè). Clean ventilating fans frequently.
This appliance should be connected directly to the fused disconnect (or circuit breaker) through flexible, armored or nonmetallic sheathed copper cable. Allow some slack in the cable so the appliance can be moved if servicing is ever necessary. A UL Listed, 1/2" conduit connector must be provided at each end of the power supply cable (at the appliance and at the junction box). When making the electrical connection, cut a 1 1/4" hole in the wall. A hole cut through wood must be sanded until smooth.
CHARACTERISTICS Components 12 D 1 Q.
Dimensional chart - Hood Distance from the Hob 6 EN
Dimensional chart - LIGHT EN 7
INSTALLATION The hood can be installed in the following ways: top air outlet, bottom air outlet, rear air outlet. Once the desired configuration has been chosen (see the diagrams below) it will be necessary to provide an opening in the wall where to house the built-in hood body case. Besides the air ducting pipes, basing on the chosen configuration, the hood has to be electrically connected, and an additional connection raceway between the hood installation area and the lighting area has to be provided.
LIGHTING UNIT INSTALLATION SCHEME LIGHTING UNIT LOWER BORDER SHALL BE INSTALLED AT THE MINIMUM DISTANCE OF 34 9/16 IN. ABOVE THE COOKING SURFACE. With the aid of the drilling template provided mark the necessary holes and drill them. 6 5/1 ø1 TOP OR BOTTOM AIR OUTLET CONFIGURATION The hood is manufactured with the air outlet at the top. • Fit the flange with non-return valve onto the air outlet position of the built-in hood body case.
REAR AIR OUTLET CONFIGURATION • Remove the suction panel by unfastening the 8 screws around the frame. • Remove the metal grease filters. • Remove the metal profile fixed to the flange by unfastening the 5 screws. • Fit the air outlet plug into the top air outlet. • Remove the rear air outlet plug . • Fit the rear air outlet flange in place of the plug Built-in hood body case installation FIXING INTO THE BRICK WALL • With the aid of pliers bend the lateral metal tongues of the built-in case.
Hood body installation • In case of the bottom air outlet configuration the hood body has to be turned 180°. • Remove the top cover of the terminal box by unfastening the two screws fixing it to the hood casing. • With the aid of pliers brake through a hole inside the terminal box providing thus for a passage of the electrical connection for the lighting unit. • Place the hood body inside the built-in case paying attention that the screws of the built-in case fall to the gaps of the hood body.
Lighting unit installation • Provide for passage of the electrical connection wires with the hood body. • Slide the top cover downwards, unfastening the two side screws and taking care not to scratch the tubular support members. • Insert the 4 plugs D into the earlier drilled holes. • Decide the height of the light; loosen the grub screws on the outer columns to allow the light to slide up and down. Take care not to scratch the columns when sliding. • Fasten the light to the ceiling using 4 screws C.
Electrical connection ! WARNING ELECTRICAL SHOCK HAZARD • Disconnect power before making electrical connctions. • Connect ground wire to green ground screw in terminal box. green ground • Connect the red wire of the Light cable with the red lead in the hood screw hood wiring hood wiring using a twist-on connector; connect the purple wire of the Light cable with the purple lead in the hood using a twist-on connector.
USE Control Panel S1 L T1 T2 T3 T4 The hood can be switched on pushing directly onto the requested speed without firstly having to select 0/1 button. LED FUNCTIONS L 0/1 Light Turns lighting on and off. T1 0/1 Motor Fixed T2 T3 Speed Speed Fixed on T4 Speed Fixed Flashing S1 Led Fixed Flashing First speed. When pressed for about 2 seconds the motor is switched off. Second speed. Third speed. Max. speed Intensive speed. Suitable for the strongest cooking vapours and odours.
Lighting LIGHT REPLACEMENT 20 W halogen light. • Extract the lamp from the Support. • Replace with another of the same type, making sure that the two pins are properly inserted in the lamp holder socket holes.
436002499_02 - 041103
