Installation Guide

ManualsBrandsEZ Shelf ManualsAdjustable Mount Wire Shelving KitsEZS-RS72S

EZ Shelf Instructions – Closet Shelf & Rod

**WATCH 2 Installation videos BEFORE Installation: www.ezshelf.com/videos

Included Plastic Parts

Tube Receivers – Left and Right

1 - Center Support

1 - End Bracket – NOT INCLUDED- For mounting to Back Wall, Corners &

Left shown

Joining Shelves together for longer Shelf & Rod Unit

End Bracket will NOT be needed if installing between two sidewalls (sides of a closet).

For 1 Side Wall you will need to purchase 1 End Bracket (EZS-EB-SCRW for Shelf & Rod) or (EZS-EB-SW for Shelf).

If you have NO Side Walls and want to attach only to Back Wall you will need to purchase 2 End Brackets.

40-44” Wide Closet - If installing in a tight space (40-44” wide) insert ALL tubes into both left and right Tube Receivers

BEFORE step 1 & either have someone help hold the Shelf or mount Center Support Bracket First.

The tubes will NOT fit into a tight space once the brackets are mounted to the wall.

Mounting Tube Receiver to Sidewall

1. Measure & Mark Sidewall from floor up

Suggested Shelf Heights: Single Hanging: 60” - 80” from floor to top of shelf.

Double Hanging: 80” - 84” from floor to top shelf & 40” - 42” for bottom shelf.

2. Tape Tube Receiver Template to sidewall – Must be Level.

3. Mark Four Screw Holes with Pencil.

Note: Tube Receiver Installation: Large Holes MUST be on Top & Small, Protruding TAB MUST touch back wall (see below).

Left Tube Receiver

4. CHECK FOR STUDS–Push nail/screw into drywall-If it doesn’t go all the way in you may be hitting a stud or other object.

5. Drywall Anchor Instructions- Drill/poke a small hole into wall. Push TIP ONLY of Anchor into drywall & Screw in plastic

anchors (see drywall anchor pictures below). Use screwdriver/electric drill (on LOW setting – do NOT over tighten).

Note: EZ Shelf will hold 200 lbs. WITHOUT securing to studs.

Do NOT use included anchors when:

 You HIT A STUD: Drill “pilot” hole into stud & attach screw directly to stud.

 PLASTER WALLS: Drill “pilot” hole - Use plastic or lead anchors & appropriate screws.

 CONCRETE WALLS: Drill “pilot” hole (may need hammer drill) - Use concrete anchors/screws.

Drywall Anchor & Screw Installation Diagrams (see ezshelf.com/videos for more information):

TAB should be

touching against

back wall

Large Holes

on Top

Anchor/Screw Hole

Left Tube Receiver has SMALLER tube

diameter & holes than Right Tube Receiver

1. Press Tip of

SnapSkru anchor

into Drywall using

screwdriver or

screw gun. Screw

anchor clockwise

into drywall until

anchor stops flush

with wall.

2. Place

item over

anchor &

insert

screw.

3.Tighten

screw

until flush

with item.

Summary of content (2 pages)

PAGE 1
EZ Shelf Instructions – Closet Shelf & Rod **WATCH 2 Installation videos BEFORE Installation: www.ezshelf.com/videos Included Plastic Parts Tube Receivers – Left and Right 1 - Center Support 1 - End Bracket – NOT INCLUDED- For mounting to Back Wall, Corners & Joining Shelves together for longer Shelf & Rod Unit Left shown End Bracket will NOT be needed if installing between two sidewalls (sides of a closet).
PAGE 2
6. Insert Back Tube (closest to back wall) into installed Tube Receiver (use hammer or mallet if necessary). 7. Attach Back Tube to other Tube Receiver and Extend to opposite sidewall. 8. Place Level on Back Tube & then also on Tube Receiver – Must be level - Mark Holes on wall with pencil. 9. Attach Tube Receiver to Wall (Repeat Steps 4 and 5 above from page 1) 10. Insert 4 other Top Tubes into both Tube Receivers. Do NOT insert Hanging Rod tube (Bottom of “L”) until after step 13. 11.