Installation Guide

ManualsBrandsEZ Shelf ManualsAdjustable Mount Wire Shelving KitsEZS-K-SRI

or email EZ@EzShelf.com

REACH IN CLOSET INSTRUCTIONS

Included Plastic Parts

Tube Receivers – 5 Left & 5 Right

5 Center Supports

4 End Brackets – optional use

left shown

For EZ Installation, Read Instructions & WATCH installation videos BEFORE beginning installation.

Installation videos: www.ezshelf.com/videos

This Photo shows EZS-K-WRI White Reach in Closet Kit which includes 1 Closet Shelf & Rod unit (40” - 73”),

1 Closet Shelf & Rod unit (28”- 48”), 3 Shelf Units (each 28” - 48”) & 3 End Brackets (1-EZS-EB-SCRW, and

2-EZS-EB-SW).

This can also be configured with the shelves on the left side.

Other layouts are possible depending upon closet measurements & your requirements.

Please call or email for design or installation assistance.

1) Measure each wall of closet before beginning and design your closet space(s).

2) Read Instructions & Watch 2 Minute Videos

The above picture has the following configuration:

Top Shelf & Rod - 1 Shelf and Rod Unit (40 – 73”) – EZS-SCRW72

Bottom Shelf & Rod & Shelf – 1 Shelf & Rod Unit (28 – 48” – EZS-SCRW48) joined with

1 Shelf Unit (28 – 48” EZS-SW48) and 1 included End Bracket EZS-SW

2 Additional Shelves (28-48” EZS-SW48)_ and 2 included Shelf End Brackets (EZS-EB-SW)

Shelf units are mounted to a side wall and End Brackets are used for mounting the other side to the Back Wall.

1 Shelf & Rod Unit Joined with 1

Shelf Unit with included

Shelf & Rod End Bracket

EZ-EB-SCRW

Shelf Unit Mounted to Side Wall &

Back Wall

with included 1 Shelf End Bracket

EZS-EB-SW

Summary of content (4 pages)

PAGE 1
or email EZ@EzShelf.com REACH IN CLOSET INSTRUCTIONS Included Plastic Parts Tube Receivers – 5 Left & 5 Right 5 Center Supports 4 End Brackets – optional use left shown For EZ Installation, Read Instructions & WATCH installation videos BEFORE beginning installation. Installation videos: www.ezshelf.
PAGE 2
Installation Instructions for Shelf & Rod Unit mounted to 2 Side Walls (like the side of a closet). If beginning with an End Bracket, skip to step #15. Mounting Tube Receiver to Sidewall 1. Measure & Mark Sidewall from floor up Suggested Shelf Heights: Single Hanging: 60” - 80” from floor to top of shelf. Double Hanging: 80” - 84” from floor to top shelf & rod & 40” - 42” for bottom shelf & rod. 2. Tape Tube Receiver Template to sidewall – Must be Level. There is a left and right template. 3.
PAGE 3
11. Twist both ends of tubes until fully secured. 12. Place Center Support so the tubes rest in the slots (preferably thicker part of tubes). To make sure Center Support contacts ALL Tubes - Push center support UP from Bottom. Then Mark Holes on Back Wall. Note: DO NOT rest Center Support on tube extension sleeves. 13. Attach Center Support using anchors and screws (see steps 4-5 on page 1).
PAGE 4
Optional Shelf Top Assembly – See Below Pictures: White – EZS-ST-W (6 pieces for up to 73” Shelf), Silver EZS-ST-S (6 pieces for up to 73” Shelf), 1. After EZ Shelf unit has been installed, the shelf top will easily snap onto the middle tube of the unit. 2. Push shelf top pieces together for continuous look. 3. If needed, shelf top will break along the lines to fit the shelf needed. 4. A usable unit of shelf top must have at least three pieces. 5.