Installation Instructions

4 E-Z Build Shed Building Guide 10'×10' ∙ 10'×12' ∙ 10'×14' ∙ 10'×16' ∙ 10'×20'
TRIMS: Cut to t and attach corner trim & end wall fascia
trim; likewise with 1×4 trim over doors.
STEP 14. ROOF & TRIMS
STEP 11. FLOOR SHEATHING
STEP 12. SIDE WALLS
STEP 13. FASCIA/SOFFIT
• 10' Building: Cut (2) ¾" 4×8 sheets to 47½"×96". Cut a ¾" 4×8
sheet into 24"×96" & 24"×95½". Cut another sheet to 24"×23½".
• 12' Building: Use (1) ¾" 4×8 sheet. Cut (2) ¾" 4×8 sheets to
47½"×96". Cut another ¾" 4×8 sheet to 24"×95½" & 24"×47½".
• 14' Building: Use (2) ¾" 4×8 sheets. Cut (1) ¾" 4×8
sheet to 47½"×96". Cut (1) 4×8 sheet into 23½"×96" &
24"×95½". From another sheet cut a piece 24"×71½".
• 16' Building: Use (2) ¾" 4×8 sheets. Cut (2) 4×8
¾" sheets to 47½"×96".Cut (1) to (2) 24"×95½".
• 20' Building: Use (3) ¾" 4×8 sheets and (1) 24"×48" piece.
Cut (2) ¾" 4×8 sheets to 47½"×96". Cut (1) into (2) 24"×95½".
Notch and adjust as necessary. Stagger end butt joints front to back. Fasten using 8d nails.
•10' Building: Use (2) full OSB 4×8 sheets. From a 4×8 OSB
sheets: Cut (2) 21¼"×72", (2) 24"×48" & (2) 21¼"×48".
•12' Building: Use (2) full 4×8 OSB sheets. From a 4×8 OSB
sheets: Cut (2) 48"×48"; (1) to (2) 21¼"×48"; and (1) to (2)
21¼"×96". See Figure 12.
•14' Building: Use (2) full 4×8 OSB sheets. From others: Cut
(2) to 21¼"×72"; (2) to 72" and (1) to (2) 21¼"×96".
•16' Building: Use (4) full 4×8 OSB sheets. Cut (2) more into
(4) 21¼"×96".
•20' Building: Use (4) full 4×8 OSB sheets. From others: Cut
(2) into (4) 21¼"×96"; (1) into (2) 21¼"×48"; and (1) into (2)
48"×48".
Stagger ends front to back. Nail with 6d nails 8" on center
Apply roof edge, felt, and shingles as written on bundles.
• 10' Building: Cut (5) 4×8 siding sheets to 83". Cut
(2) of those to 47½" wide and (1) into (2) 23½"×83".
• 12' Building: Cut (6) 4×8 siding sheets to 83".
Cut (4) of those to 47½" wide.
• 14' Building: Cut (7) 4×8 siding sheets to 83". Cut (2) of
those to 47½" wide and (1) into (2) 23½"×83".
• 16' Building: Cut (8) 4×8 siding sheets to 83".
Cut (4) of those to 47½" wide.
• 20' Building: Cut (10) 4×8 siding sheets to 83".
Cut (4) of those to 47½" wide.
48"×21¼"
48"×21¼"
72"×21¼"
96"×21¼"
96"×48"
96"×48"48"×48"
24"
×
48"
69¼"
69¼"
10'
12'
4 Pieces 1×6
Cut to t.
4 Pieces 1×4
Cut to t.
End wall
fascia trim
End wall
corner trim
Notch for
Uprights
Seams
10'×12'
Floor
Shown
10'
24"
96"
47½" 48"
95½"
47½"
NOTE: Notch siding at tops to t around
E-Z frame overhangs. Place cut edges
at corners. Make certain end walls and
frames are plumb (vertically level) and
then fasten using 6d nails.
•10' Bldg: Use (2) 1×6×10' boards •12' Bldg: Use (2) 1×6×12' boards
•14' Bldg: Use (2) 1×6×14' boards •16' Bldg: Use (2) 1×6×16' boards
•20' Bldg: Use (4) 1×6×10' boards. Nail to the exposed ends of the roof
frame members using 6d nails. Place top edge of fascia board ½" above
the top of the roof frame member to cover exposed roof edge. Use 1x6
boards for the soft: •10' Bldg: 10' boards •12' Bldg: 12' boards
•14' Bldg: 6' & 8' boards •16' Bldg: 10' & 6' boards •20' Bldg: 10' boards
Raised
½"
1×2
Nailer
1×6 Fascia
Board
1×6 Soft Board
Figure 10
Figure 11
Figure 12