Instructions / Assembly
Table Of Contents
- 1. BASIC SYSTEM COMPONENTS
- 2. PLATFORMS
- 2.1. INSTALL PLATFORMS
- 2.2. INSTALL SUPPORT TUBES AND FEET, THEN ADJUST PLATFORM HEIGHT
- 2.3. CONNECT TWO PLATFORMS TOGETHER
- 2.4. 45-DEGREE ANGLE PLATFORM
- 2.5. 8’ X 5’ TURN BACK PLATFORM
- 2.6. LOW PROFILE PLATFORM
- 2.7. INSTALL UNIVERSAL ANGLE BRACE – PLATFORMS
- 2.8. INSTALL UNIVERSAL CROSS BRACE
- 3.1. CONNECT RAMP SECTIONS
- 3.2. INSTALL RAMPS ON PLATFORMS
- 3.3. ATTACH SUPPORT LEG BRACKETS AND LEGS TO RAMPS
- 3.4. INSTALL UNIVERSAL ANGLE BRACE - RAMPS
- 3.5. INSTALL GROUND TRANSITION RAMP
- 3.6. INSTALL A SINGLE RAMP RUN TO AN EXISTING STRUCTURE
- 3.7. ANCHOR RAMP UPPER TRANSITION
- 3.8. ANGLE RAMPS WITH RESPECT TO PLATFORMS, PORCHES, OR DECKS
- 4.1. RAMP WITHOUT HANDRAILS
- 4.2. RAMP HANDRAILS
- 4.3. ASSEMBLE STANDARD PLATFORM HANDRAILS
- 4.4. INSTALL STANDARD PLATFORM HANDRAILS
- 4.5. 8’ X 5’ TURN BACK PLATFORM HANDRAILS
- 4.6. 45-DEGREE ANGLE PLATFORM HANDRAILS
- 5.1. If installing a closure on a platform in the “straight” configuration, the 2” x 2” angle post will already be in place; skip to step 5.4
- 5.2. If installing on a platform in the ‘turn’ configuration, install the 2” x 2” angle post not attached to a platform handrail in the open platform corner pocket. Align the bottom of the post with the bottom of the corner pocket and tighten the set ...
- 5.3. Install an angle cap on top of the handrail post (FIG. 5.1). Use construction adhesive to bond the cap in place.
- 5.4. First install the top rail, the rail connecting the ramp handrail to the platform post.
- 5.5. TWO-LINE CLOSURE
- 5.6. VERTICAL PICKET CLOSURE
- 5.7. TWO-LINE TURN BACK CLOSURE
- 6.1. SECURE RAMP TO PLATFORM
- 6.2. INSTALL RAMP HANDRAIL END LOOPS
- 6.3. INSTALL RAMP HANDRAIL END CAPS
- 6.4. INSTALL RAMP CORNER PROTECTORS
- 6.5. TOUCH-UP ARCHITECTURALLY FINISHED HANDRAILS
- 6.6. FINAL CHECKS
- 7.1. RAMP SUPPORT TOP
- 7.2. RAMP LOWER TRANSITION
- 7.3. SINGLE BRIDGE PLATE
- 7.4. LANDING PAD
- 7.5. PLATFORM TIE STRAPS
- 7.6. LIGHTNING GROUND ROD
- 7.7. TIE DOWN
- 7.8. GATE
- 7.9. CONNECT 45-DEGREE ANGLE PLATFORM WITH TWO-LINE RAILS TO STANDARD PLATFORM
- 8.1. PERIODIC MAINTENANCE AND SAFETY
PATHWAY
®
3G Modular Access System Assembly Manual
Page 6 of 75
1
1. BASIC SYSTEM COMPONENTS
Because each ramp configuration will differ from one another, your system may or may not contain all these
basic system components. Identify your system components before you begin.
SURFACE OPTIONS
SOLID SURFACE EXPANDED METAL SURFACE
RAMP AND RAMP HANDRAIL OPTIONS
RAMP W/O HANDRAILS RAMP W/ TWO-LINE HANDRAIL
RAMP W/ VERTICAL PICKETS RAMP W/ HORIZONTAL PICKETS