Instructions / Assembly
Table Of Contents
- 1. BASIC SYSTEM COMPONENTS
- 2. PLATFORMS
- 2.1. INSTALL PLATFORMS
- 2.2. INSTALL SUPPORT TUBES AND FEET, THEN ADJUST PLATFORM HEIGHT
- 2.3. CONNECT TWO PLATFORMS TOGETHER
- 2.4. 45-DEGREE ANGLE PLATFORM
- 2.5. 8’ X 5’ TURN BACK PLATFORM
- 2.6. LOW PROFILE PLATFORM
- 2.7. INSTALL UNIVERSAL ANGLE BRACE – PLATFORMS
- 2.8. INSTALL UNIVERSAL CROSS BRACE
- 3.1. CONNECT RAMP SECTIONS
- 3.2. INSTALL RAMPS ON PLATFORMS
- 3.3. ATTACH SUPPORT LEG BRACKETS AND LEGS TO RAMPS
- 3.4. INSTALL UNIVERSAL ANGLE BRACE - RAMPS
- 3.5. INSTALL GROUND TRANSITION RAMP
- 3.6. INSTALL A SINGLE RAMP RUN TO AN EXISTING STRUCTURE
- 3.7. ANCHOR RAMP UPPER TRANSITION
- 3.8. ANGLE RAMPS WITH RESPECT TO PLATFORMS, PORCHES, OR DECKS
- 4.1. RAMP WITHOUT HANDRAILS
- 4.2. RAMP HANDRAILS
- 4.3. ASSEMBLE STANDARD PLATFORM HANDRAILS
- 4.4. INSTALL STANDARD PLATFORM HANDRAILS
- 4.5. 8’ X 5’ TURN BACK PLATFORM HANDRAILS
- 4.6. 45-DEGREE ANGLE PLATFORM HANDRAILS
- 5.1. If installing a closure on a platform in the “straight” configuration, the 2” x 2” angle post will already be in place; skip to step 5.4
- 5.2. If installing on a platform in the ‘turn’ configuration, install the 2” x 2” angle post not attached to a platform handrail in the open platform corner pocket. Align the bottom of the post with the bottom of the corner pocket and tighten the set ...
- 5.3. Install an angle cap on top of the handrail post (FIG. 5.1). Use construction adhesive to bond the cap in place.
- 5.4. First install the top rail, the rail connecting the ramp handrail to the platform post.
- 5.5. TWO-LINE CLOSURE
- 5.6. VERTICAL PICKET CLOSURE
- 5.7. TWO-LINE TURN BACK CLOSURE
- 6.1. SECURE RAMP TO PLATFORM
- 6.2. INSTALL RAMP HANDRAIL END LOOPS
- 6.3. INSTALL RAMP HANDRAIL END CAPS
- 6.4. INSTALL RAMP CORNER PROTECTORS
- 6.5. TOUCH-UP ARCHITECTURALLY FINISHED HANDRAILS
- 6.6. FINAL CHECKS
- 7.1. RAMP SUPPORT TOP
- 7.2. RAMP LOWER TRANSITION
- 7.3. SINGLE BRIDGE PLATE
- 7.4. LANDING PAD
- 7.5. PLATFORM TIE STRAPS
- 7.6. LIGHTNING GROUND ROD
- 7.7. TIE DOWN
- 7.8. GATE
- 7.9. CONNECT 45-DEGREE ANGLE PLATFORM WITH TWO-LINE RAILS TO STANDARD PLATFORM
- 8.1. PERIODIC MAINTENANCE AND SAFETY
PATHWAY
®
3G Modular Access System Assembly Manual
Page 24 of 75
1
2.6.7.8. The installed low profile ground or bridge transition is shown (FIG. 2.19).
2.6.7.9. If using as a bridge transition, check and adjust the height of the platform until
the bridge transition is level. Attach the bridge transition to the platform or
landing using fasteners appropriate for the surface (provided by the installer)
through the two 1/4” holes in the corners. If using as a ground transition,
anchoring is optional.
FIG. 2.19
2.7. INSTALL UNIVERSAL ANGLE BRACE – PLATFORMS
For added stability, any platform with a walking surface over 36″ high requires bracing. The
PUAB (PATHWAY ANGLE BRACE) is used for surfaces 36″ up to 71″.
2.7.1. Angle braces come in pairs. Use four pairs per platform (one pair per support tube,
or side) or six pairs when two platforms are connected.
2.7.2. Use two brace bands to secure the ends of the two angle braces nearest the twist to
the support tube using a 5/16" bolt, flat washer, and nut (FIG. 2.20).
2.7.3. Opposite ends of the braces are attached to the bottom of the platform side rail at
90-degrees to each other using a 1/4″x 1” long self-drilling screw (FIG. 2.20).
Ensure that all angle braces are secured before using platform.
FIG. 2.20
LOW PROFILE GROUND TRANSITION
OR BRIDGE TRANSITION