Instruction manual

ManualsBrandsEYEZONE ManualsComputer equipmentB1080PX-4

EYEZONE B1080PX-4

User Manual

Aug 13, 09

FCC Notices

It’s herewith confirmed to comply with the requirements of FCC Part 15 Rules. Operation is

subject to the following two conditions:

z This device may not cause harmful interference.

z This device must accept any interference received, including interference that may

cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

residential installation. This equipment generated uses and can radiate radio frequency

energy and if not installed and used in accordance with the instruction manual may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio of television reception, which can be determined by turning the

equipment off or on, the user is encouraged to try to correct the interference by one or more

of the following measures:

z Reorient or relocate the receiving antenna.

z Increase the separation between the equipment and receiver.

z Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

z Consult the dealer or an experienced radio TV technician for help.

CE Declaration

This device complies with CE class B.

EN55022 IEC 61000-4-4

EN61000-3-2 IEC 61000-4-5

EN61000-3-3 IEC 61000-4-6

EN55024 IEC 61000-4-8

IEC 61000-4-2 IEC 61000-4-11

IEC 61000-4-3

Printed in Taiwan R.O.C.

All contents are subject to change without notice.

All trademarks are the property of their respective owner.

Summary of content (23 pages)

PAGE 1
FCC Notices EYEZONE B1080PX-4 It’s herewith confirmed to comply with the requirements of FCC Part 15 Rules. Operation is subject to the following two conditions: This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
PAGE 2
CONTENTS 1. 2. 3. 4. 5. Package Contents……………………..……………………….. Introduction……………………………….……………………... Features………………………………………….……………… Hardware Overview…………………..………………………... Remote Control…………………………..…………………….. 5.1 Entering Text or IP Address…………..…………………… 6. Start the B1080PX-4…..……………….………………………. 7. Setting Up……………………………………………………….. 7.1 Network Setup……………………..….……………………. 7.2 FTP Setup…………………………………………………… 7.3 Video Setup…………………………..…………………….. 7.4 Other Setup………………………………..……………….. 7.5 Scrolling Text Setup………….
PAGE 3
. FEATURES High-performance and high stability: With the same resolution and bit rate as Blu-ray players’. The source of HD WMV9 MP@HL (Main Profile / High Level) supports resolution up to 4. HARDWARE OVERVIEW 1920x1080 (1080P) and the maximum bit rate is 40Mbps. Supports multiple file formats: WMV9 and WMA. Supports HDMI input to display videos from HDMI sources (such as HDMI DVD player or HDMI Game Box). Supports Video, Y.Pb.Pr, HDMI, VGA and Audio output.
PAGE 4
5. REMOTE CONTROL 6. START THE B1080PX-4 Power On 1 Power on/ off z Insert the CF memory card that has Picture, Music, Movie or WMV9 files. 2 Select the output mode z Press the “POWER” button to power on the Eyezone B1080PX-4, and then press the “TV 3 Numeric Key 4 Delete last entry 5 Select a function or to play the selected file 6 Open the setup menu Mute sound 7 OSD display function on/ off 8 Auto-play function on/ off 9 Mute sound MODE” button to select the output mode.
PAGE 5
7.1 NETWORK SETUP (continued) 7. SETTING UP In the main menu, using the “▼” button on remote control to select the “SETUP” item, and then server or you want to use Local FTP Server function, enter the fixed IP address, Mask, Gateway press the “ENTER” button. You will be presented with the Eyezone B1080PX-4 settings screen. and DNS for the Eyezone B1080PX-4. You can also press the “SETUP” button on remote control to directly open the settings screen. PS. Refer to 5.
PAGE 6
7.1.2 Setting the Network from the IP Detect Tool Step3: Double click on the With the bundle tool “IP Detect”, user could search B1080PX-4 on the local area network. User could Step4: Click on the “Auto Detect” button, then the tool will show all available B1080PX-4 in the local also change the IP setting via this tool. For example, user might assign a static IP to B1080PX-4 by the icon to start the tool. area network.
PAGE 7
Step6: The default IP mode of B1080PX-4 is DHCP. User should change the mode to “Manual”, if he 7.2 FTP SETUP wants to assign a static IP address to B1080PX-4. Then enter the preferred “IP”, “Net Mask” and “Gateway” in the “Network Setting”. Finally, click on the “Setup” button for completing the setting. NOTE: The IP setting will not show on the OSD menu instantly, but it should be available after pressing “Setup” button. The prefer IP address will show on the OSD menu when B1080PX-4 restart.
PAGE 8
② Local Time: Set the system time manually. NOTE: GMT and applied regions Time Zone Region Time Zone (GMT-12:00) (GMT-11:00) Eniwetok, Quazalen Midway, Ireland, Samoa (GMT+02:00) (GMT+03:00) (GMT-10:00) Hawaii (GMT+03:00) (GMT-09:00) (GMT+03:00) (GMT+03:00) Kuwait, Raid (GMT+03:30) Tehran (GMT+04:00) (GMT+04:00) (GMT+04:30) Baku, Tbilisi, Ere van Abu Dhabi, Muscat Kabul (GMT-06:00) Alaska Pacific GMT (U.S. & Canada); Tijuana Continental GMT (U.S.
PAGE 9
7.4 OTHER SETUP (continued) 7.4 OTHER SETUP Export Setting File: Press the “Enter” button to export the configuration value to the CF card. Step1: Copy the file “HDPlayerSetting.txt” on CF card to your PC. Use the “Wordpad” to open the file, and you can see all the configuration value of B1080PX-4. Step2: You can modify directly the configuration value on your PC. Example: [NETWORK] Disable Options: Disable, RJ45, WiFi The “Network” function is disabled, you can directly change the mode to RJ45.
PAGE 10
7.5 Scrolling Text Setup 8. USING THE B1080PX-4 8.1 PLAY MEDIA FILES ON THE CF CARD Step 1: Insert the CF card with media files, then turn on the Eyezone B1080PX-4 and press the “ENTER” button on the remote control when “’mnt/CF” is highlighted to take you into the CF card. Multiple Display: - Movie: Display movies (live video or stored video) with scrolling text.
PAGE 11
8.1.1 Using the Remote Control When Media File Is Playing PAUSE/STEP: Pause the playback or play frame by frame. SETUP: Press the button to adjust the brightness, contrast or saturation while the video or picture ZOOM: Zoom in/ out on the movie or picture. is playing. With the “+ VOLUME –” button. - First Press: Adjust the brightness. - Second Press: Adjust the contrast. - Third Press: Adjust the saturation.
PAGE 12
8.2 MULTIPLE DISPLAY ZONES 8.3 HDMI IN Step 1: Put movies, pictures (only supports PNG format/ size: 213x641/ 96DPI) and text file on CF card. Mode 1: Play HD Videos from HDMI sources only Picture Files If you select the “By Slide Time” item of the picture slide mode; please name the picture files 0.png ~ 9.png. If you select the “Match Video” item of the picture slide mode, the file name of the picture must be the same of the corresponding movie file.
PAGE 13
Step 4: Select the HDMI In item to directly play the live video and scrolling text on your screen. 8.
PAGE 14
Item [file] 001.mpg 002.mpg 0.png 1.png schedule.ini message1.txt Step2: Remember to save the file after editing, and named the command file d + MAC address.txt. Description Enter the filename you want to download. Example: The MAC address of B1080PX is 0013fe100000, and named the file d0013fe100000.txt. Note: The length of file name and extension cannot exceed 20 characters. NOTE: The MAC address of B1080PX will be displayed in the setup menu. The file schedule.
PAGE 15
8.5 RS-232 FUNCTION (RS-232 cable is optional) 8.6 LOG FUNCTION Use the tool “Tera Term” or other tools to control the Eyezone B1080PX-4 with ASCII command. Step1. Please turn on the Log Function first. (Refer to 7.4 Other Setup) NOTE. 1. The available baud rates is “19200”. Step2 .The new log files are automatically generated every day. The log file contains media filename 2. The reaction time of B1080PX-4 is around three seconds. and start time of playback. 3.
PAGE 16
9.1 CONTROL 9. HTTP COMMAND FUNCTION Confirm that the Eyezone B1080PX-4 is already connected to the network. (Refer to 7.1) Confirm the “Local HTTP Server” function has been enabled, and the “Local HTTP Server Setup” set has been completed (refer to 7.2). Set your router or firewall, and open a port 80 for the Eyezone B1080PX-4. The following figure is an example, please refer to your user’s manual of router for opening ports.
PAGE 17
9.2 NETWORK 9.3 SERVER - Enable: Enable or disable the FTP auto download function. - Port: The default port for FTP is 21. In most cases you should not change this number. If Network the FTP site uses a port other than 21, you should enter the correct port. - Enable: Enable or disable the network function. - IP address: Enter the domain name or IP address of the remote FTP server. - Interface: Select your network connection Ethernet (wired) or Wireless.
PAGE 18
9.4 TIME 9.5 FEATURES NTP Server - - Web Interface Enable: Enable or disable the NTP server function. - Enable: Enable or disable the HTTP command function. GMT Server: Enter the NTP server IP address like: 66.187.233.4. Time Zone: Set the time zone of your location. - Port: Enter the port of the B1080PX-4 (default port: 80) - User ID: Enter the user name of the B1080PX-4 (default ID: root). - Password: Enter the password of the B1080PX-4 (default password: admin).
PAGE 19
10.2 START THE SCHEDULE SOFTWARE 10. SCHEDULE FUNCTION NOTE: The “NTP Server” or “Local Time” must be set before using the Schedule You might double click the “Schedule Maker” icon on your desktop for opening the “Schedule Generator”. Or you might click on → → → < Function. (refer to 7.2) Schedule Maker > for starting the program. 10.1 INSTALL THE SCHEDULE SOFTWARE There are two parts of program: “Basic Schedule” and “Advance Schedule” in the window.
PAGE 20
Modify: Click this button to modify the file in the list. z Press the “SAVE” button and a pop-up window will appear. Select the path, then click the “SAVE” button Select the file that you want to modify in the list, and press the “Modify” button. to save your setup. Remove: Click this button to remove the file from the list. z NOTE: Do not rename the file (schedule.ini), otherwise the B1080PX-4 will not be able to read the file.
PAGE 21
10.2.3 Explanation of the Warning Message Step 2: Click the “Add” button in the “File Setup” section to open the “Schedule File Editor” window. Click the “Browser” button to select a file that you want to play. You can also set up the “Play Times” of the file in the window. Click the “OK” button to complete the setup. Or you can add video in schedule by There is no schedule file in the “Basic Schedule” or “Advance Schedule” can be saved.
PAGE 22
11.3 PIR SENSOR (Eyezone PIR) 11. OPTIONAL AUXILIARY EQUIPMENT 11.1 PLAY-BUTTON BOX (Eyezone BB) Application 1: The Eyezone PIR is an external remote control receiver. Application 2: The Eyezone PIR is a motion detector. The Play Button Box (Eyezone BB) supports up to 12 play-button inputs. Press one of the play buttons to play the corresponding file. Hardware Connection 11.3.1 Using the PIR Sensor Step 1: Set the repeat mode to the “Repeat Default”.
PAGE 23
11.4.2 Demo Files 12. TROUBLESHOOTING Ex. Using the wireless 5 Touch-Sensor Buttons Put 6 demo files on CF card. (1 default file and 5 demo files) NOTE: The files are sorted by filename in ascending order alphanumerically (numbers < upper case Situation letters < lowercase letter). Each button is mapped to a file by this order. For Example： There are 6 demo files on the CF card. The file names are a01.xxx, 33.xxx, b55.xxx, 1abc.xxx, 07.xxx and A01.xxx.