SecureYour Life Protect Your Dreams H.264 DIGITAL VIDEO RECORDER User’s Manual eyemax HX Series Model: HX-04/08 Rev 1.
USER’S MANUAL Safety Precautions Turn off the power of the product before installing the product. Do not plug many can be damaged, keep at least 15cm of plugs into one outlet clearance between where the product is - It can cause an electric shock or a fire. installed and where the power outlet is. Do not put any containers with liquid such - It can cause a fire, an electric shock or an as water, coffee, beverage etc. on top of the product. injury.
USER’S MANUAL CAUTION RISK OF ELECTRIC SHOCK. CAUTION! DO NOT OPEN. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
USER’S MANUAL Caution Please read the following precautions carefully before installing the product and follow the directions for installation. Do not install the product where the level of humidity, dust or smoke is high. Do no install the product where it is exposed to direct sunlight or close to the heating device. Do not install the product where there is danger of electric shock or near magnetic object.
USER’S MANUAL TABLE OF CONTENTS Chapter 1 Installation 1-1 Product characteristics ---------------------------------------------------------------------------- 8 1-2 Component ------------------------------------------------------------------------------------------- 9 1-3 Front side --------------------------------------------------------------------------------------------- 9 1-4 Rear side ------------------------------------------------------------------------------------------- 10 1-5 Remote controller
USER’S MANUAL Chapter 3 Web viewer 3-1 Installation ------------------------------------------------------------------------------------------ 60 Web viewer installation ......................................................................................... 60 3-2 Functional description --------------------------------------------------------------------------- 62 Web viewer monitoring window ............................................................................ 62 Web viewer search window.........
USER’S MANUAL CHAPTER 1 Installation 1-1 Product characteristics ------------------------------------------------------------------------- 8 1-2 Components ---------------------------------------------------------------------------------------- 9 1-3 Front side -------------------------------------------------------------------------------------------- 9 1-4 Rear side ------------------------------------------------------------------------------------------- 10 1-5 Remote Controller ----------------------
USER’S MANUAL 1-1. Product characteristics z Adopted the stable Embedded Linux z Stable file system recovery even after power supply is disconnected from a power outage. z Realized small file size and high video quality by applying the H.264. z Supports terra byte hard disk ( up to 2TB ) z Real time recording - 04CH: Up to 120IPS@704 X 240 at NTSC / Up to 100IPS@704 X 288 at PAL - 08CH: Up to 240IPS@352 X 240 at NTSC / Up to 200IPS@352 X 288 at PAL z Supports various recording resolutions and qualities.
USER’S MANUAL 1-2. Components Screws User’s Manual Remote Controller Mouse SATA cable HDD power cable Power cable Adapter Reference: The type of components can be applied differently by the option. 1-3. Front side ④ ③ ⑥ ⑦ ⑨ ⑧ ⑩ ⑪ ② ⑫ ⑤ ① POWER SWITCH: Used to turn the product on/off and when logging off. ② Front LED: The LED is turned on when the power is on , search is in active , record is in active and network is in use.
USER’S MANUAL 1-4. Rear side ② ③ ⑧ ④ ① ⑤ ⑥ ⑨ ⑦ ⑦ ⑤ ② ③ ⑧ ⑧ ④ ① ⑤ ⑥ ⑦ ⑨ ① E-Sata port for External HDD ② Camera input ③ Spot output(up) & Main Monitor output(Down) ④ Audio in and out ⑤ VGA ⑥ Network Port ⑦ USB Port ⑧ RS485, SENSOR INPUT, RELAY OUTPUT ⑨ Power input H.
USER’S MANUAL 1-5. Remote controller Reference: The shape of remote controller can be different by the model. How to set the ID of remote controller: 1. Press cancel button about 3 seconds then light of power button turns on. 2. Enter two digit numbers which is the id of remote controller using number keys. ※ You have to input ‘0’ first when you are to input one digit number. Ex) In case you want to use ‘2’ as ID, input ‘02’. 3. Every time you press the number key the light of power button will blink.
USER’S MANUAL 1-6. Connection and initial setting Caution z The camera or other external devices can be connected to this device in numerous methods. Refer to the user manual of the camera or other external device for addition information on connection methods. z When installing the camera, check whether the power of the camera is turned off. z After installing the monitor, turn on the power of the DVR. 4CH 8CH H.
USER’S MANUAL 1-7. RS-485 connection ① This device has 1 data port (RS-485). ② Use this port to connect the PTZ camera or the keypad. (Optional) ③ PTZ camera / keyboard connection i.Connect the PTZ serial communication cable to the RS-485 port. ii. When connecting the cable, make sure that the TX- of the device is connected to the RX- (TX-) of the camera (keyboard), and TX+ of the device is connected to the RX+(TX+) of the PTZ camera(keyboard). iii.
USER’S MANUAL 1-10. About internal hard disk The hard disk installed inside the device is a precision device which can be damaged even with the small impact. To prevent the hard disk from being damaged, manage the device as follows. To prevent the data loss, it is recommended to back up any important data into an external storage device. When installing or uninstalling the hard disk, you must always turn off the power of the product. z If the power is turned on, do not move the device.
USER’S MANUAL ① Install the hard disk to the bracket and tighten the 4 screws. ▶ Connecting bracket to hard disk Set the SATA cable connection port to lower direction to install the hard disk to the bracket Connect the bracket marked as “L” To the left side of hard disk Connect the bracket marked as “R” to the right side of hard disk ② Connect the SATA cable to the hard disk ▶Connect power cable ▶Connect SATA cable H.
USER’S MANUAL ③ Connect the SATA cable to the SATA port of the main board. <8CH> <4CH> The first SATA cable port on the main board must be connected at all times. If a hard disk is not connected, this device may not operate normally. A. ① Close the cover of the main unit. ② Tighten the screws. ③ After installing the hard disk, you must format the hard disk from the setting menu. Hard disk replacement First turn of the power of the device and then unplug the power.
USER’S MANUAL B. Recommended list of hard disk - Hard disks of below are the ones proved to be compatible through experiment. - Please refer to when adding or replacing the hard disk. Manufacturer Model name ST3250312CS ST3250310CS Seagate Capacity 250GB ST3320613AS 320GB ST3500312CS 500GB ST3750330SV 750GB ST31000322CS ST31000528AS 1TB ST31500341AS 1.5TB ST32000542AS 2TB Notice: HDD not in the recommended list may not work properly even if it is detected by DVR.
USER’S MANUAL CHAPTER 2 Main system application 2-1 Operation ---------------------------------------------------------------------------------------------19 Start up ................................................................................................................ 19 Shutdown ..............................................................................................................
USER’S MANUAL 2-1. Operation 1) Start up 1. Press power button to turn on this device, then it boots with power indicator light turned on. 2. After booting Login window will be displayed. ① ② Notice!: without login by any user, DVR works as “guest” mode and only the live display can be controlled. After login by admin, DVR setting is enabled. H.
USER’S MANUAL ① [User] You may select user to login and authority is restricted by kind of user. The access rights can be set for each user. I. admin for system administrator (Access rights to Live, Search and Setup) II. guest (Access rights to Live only) III. user1/user2/user3 for general user (Access rights can be set by administrator) ② [Password] The default user is set to ‘admin’ with password: 000000. Click button then you will see the screen keypad as right. 3.
USER’S MANUAL 2) Shutdown 1. Press Log out button in Main Menu while you are logged in, then logout window will be displayed as below. A B C A. Selection: Select “Logout” or “Shutdown”. B. User: Display current user has logged. C. Password: Input password. 2. Click “OK” button to “Logout” or “Shutdown”. H.
USER’S MANUAL 2-2. Live display ① ② ③ ④ ⑥ ⑤ ① [Camera name] Shows camera name If you want to modify channel name, you can do so by selecting [Setup] Æ [Video/Audio] Æ [Camera] ② [Status icon] (OSD) Status icon shows current status of camera/recording. OSD feature Item Icon Description Audio icon Camera Motion icon PTZ icon Continuous recording Emergency recording Recording Recording by motion No recording Recording by sensor H.
USER’S MANUAL ③ [Channel selection] Selected channel shows green rectangle on the edge of the screen. ④ [Live view] (Live button on the remote controller) It shows current live view as real time. ⑤ [Current date/time] A. It shows current date/time. You can change date/time setting at [Setting] Æ [System] Æ Date/Time.
USER’S MANUAL 5)[System log] You can see log in time and information of DVR This shows the system log in DVR. Click button from live screen to show the list of system log. You can see the log of previous date or next date by using buttons. You can see the previous or next log list by using buttons. Click “OK” button to close window. H.
USER’S MANUAL 6)[system information] a. Model: It displays the name of model. b. Language: It displays language currently set. c. IP address: It displays IP address. d. MAC address: It displays MAC address. e. F/W version: It displays the version number of firmware. f. OS version: It displays the version number of OS. g. Video type: It displays video input/output signal type of NTSC or PAL. When video input comes in, it will be automatically detected and cannot be set by user. h.
USER’S MANUAL 10) [Auto Sequence] Push the icon, you can monitor the picture one by one automatically. 11) [Alarm] This button is used to turn off alarm out put 12) Network status This button network connection status When the light in on(Blue) it means DVR connected to network, it is black, the net work connection is off. ⑦ [System control toolbar – Search screen] ② ③ ④ ⑤ ① ⑥ 1. [Playback date/time] ⑦ ⑧⑨ ⑩⑪ ⑫⑬⑭⑮ It shows the date/time currently playback. 2.
USER’S MANUAL 10. [Previous frame] It displays previous frame and pause. (1 step backward play) 11. [Fast backward playback] 12. Click this button to playback fast backward. The speed of fast backward playback can be set to one of the following, X2, X4, X8, and X16.[Stop] Click this button to stop playback. 13. [Forward playback] Click this button to playback forward as normal speed. 14. [Fast forward playback] Click this button to playback fast forward.
USER’S MANUAL 2-3. System setting System setting can be configured by setup menu. Working condition can be specified by mouse / remote controller. Only admin user can setup system configuration by menu. ※ Press “Menu” on the remote controller and use Left/Right/Up/Down button to select menu by pressing “OK” button. ( Left/Right : Top menu, Up/Down : Sub Menu ) 1) System ① ② ③ ④ ⑤ ① [General setup] You can specify the system configuration by this menu. Use button to change configuration. A.
USER’S MANUAL ②[Date/Time] Specify date and time of system. You can specify setting by using Select date and time, then you will see virtual keypad as below. button A.Date/Time: Specify current date and time B.Time zone: Specify the time zone. C.NTP Server: It supports using internet time server to synchronize time. D.Format: Specify the display format of date/time. Ex.) Setting as “DD/MM/YYYY AM/PM” will displays “16/12/2010 AM 12:00”.
USER’S MANUAL ③ [F/W update] It is used for updating firmware. A. File: Select a firmware file to update using buttons after putting USB Memory stick. B. Refresh: Read list of files from USB memory. C. OK: Starts updating firmware with selected file. ④ [Setting update] It is used to import or export setting values. H.
USER’S MANUAL A. Import: Imports setting values from USB memory. B. Export: Exports setting values to USB memory. C. Refresh: Reload files from USB memory. Caution USB memory stick is needed to update F/W or setting values. Once you disconnected and reconnect USB memory, you should press “Import” button to read list of file from USB memory. “USB is not detected.” Message will be shown when you are to run updating without connected USB.
USER’S MANUAL 2) Video / Audio On this menu, camera, recording, color, OSD, display, audio, and PTZ can be configured. ① ② ③ ④ ⑤ ⑥ ① [Camera] You can specify channel name of camera. A. Camera no.: Select the camera number to change name. B. Camera name: Input camera name (Maximum 12 characters) C. Audio: Select camera to associate with each audio input. ② [Recording] You can specify recording configuration. H.
USER’S MANUAL A. Total: Max frame rate has restricted by screen resolution. B. Resolution: Specify resolution of recorded video. (CIF / Half-D1 / D1) C.Camera: Select camera to set frame and quality. D.Quality: Specify image quality for selected camera. (Very high, High, Normal, Low, Very low) E. Normal frame rate: You can specify recording frame rate when recording method is continuous for selected camera. ※ Frame rate cannot exceed event frame rate. F.
USER’S MANUAL ④ [OSD] You can set the items of OSD to be displayed, which are camera name, status icon, current date/time, video loss and transparency of OSD. If transparency is 10%, the OSD is displayed most transparently. On the other hand, if the transparency is 100%, the OSD is displayed as opaque. ⑤ [Display] You can set the position of current date/time and each channel name. H.
USER’S MANUAL A. Time bar position: Select one from “Left”, “Center”, and “Right”. B. Channel name position: Select one from “Left-top”, “Left-bottom”, and “Right-bottom”. ⑥ [PTZ] It is used to operate the PTZ camera connected to RS-485. It is needed to set the configuration between PTZ camera and DVR to use PTZ camera. B A A. Selecting PTZ Camera B. Panning or tilting camera. C. Use OSD of camera. D. Zoom: Zoom in or out. E. Focus: Focus near or far. F. Iris: Iris in or out. G.
USER’S MANUAL xii. SPD-2300 / 3000 / 3300 / SAMSUNG Co.,Ltd xiii. SUNGJIN / SUNGJIN Co.,Ltd xiv. DSC-200 / DYNACOLOR,INC xv. V1305R-DC / V1300RB / CRX – 1013 / VICON I. Device ID: Specify the device address of PTZ camera. J. Baud rate: Specify the speed of serial communication (bps). The default baud rate value is “9600 bps”. ※ It can be set as one of these values. (1200/ 2400/ 4800/ 9600/ 19200/ 38400/ 57600/ 115200 bps) Notice Basically DVR support one RS-485 port for PTZ connection. H.
USER’S MANUAL 3) Event You can specify the processing when event occurs like sensor, motion detection, video loss, event filters, and schedule. ① ② ③ ④ ⑤ ⑥ ⑦ ① [Device] You can set enable or disable sensor, alarm, and alert. A. Sensor no.: Select sensor no. (1 ~ 4) B. Activate sensor: Check if you want to enable the sensor. C. Type : Specify the sensor type is “N.O.” or “N.C.”. i. N.O.(Normal Open): The type of input device is opened normally. ii. N.C.
USER’S MANUAL ② [Sensor] You can specify the processing when event occurs from input device. A. Sensor no.: Selecting sensor number. (1 ~ 4) B. Channels: Setting association with selected sensor event. C. Alarm: Setting association with the sensor input. D. Alert: Setting sound a buzzer when event occurs from input device. H.
USER’S MANUAL ③ [Motion] You can specify the process when motion is detected. A. Camera no.: Selecting camera which is associated event. B. Channels: Setting association with selected motion detection event. C. Alarm: Setting association channel with motion detection. D. Alert: Setting sound a buzzer when event occurs with motion detection. H.
USER’S MANUAL ④ [Motion zone] Setting area of motion detection. Drag mouse while left button pressed to set or release the area of motion detection. ( Red: motion zone, Grey : non motion zone ) A. Channels: Selecting a channel to set motion zone. B. Sensitivity: Setting the motion sensitivity. (Very high/High/Normal/Low/Very low) C. Pixel sensitivity: Setting the detailed motion sensitivity by block unit. (Very high/High/Normal/Low) D. Select all: Selecting entire area. E.
USER’S MANUAL ④ [Video loss] You can specify the processing when video loss. A. Camera no.: Selecting camera which is associated with video loss event. B. Channels: Selecting channels to record when video loss event occur from the specified camera. C. Alarm: Setting alarm out when video loss. D. Alert: Setting sound a buzzer when video loss. H.
USER’S MANUAL ⑤ [Event filter] Specifying the event which will be sent to the central monitoring center and E-mail. A. System start: Enabling or disabling the system start event. B. Setting change: Enabling or disabling the setting change event. C. Normal shutdown: Enabling or disabling the system shutdown event. D. Login: Enabling or disabling the login event. E. Logout: Enabling or disabling the logout event. F. HDD full: Enabling or disabling the HDD full event. G.
USER’S MANUAL ⑥ [Schedule] You can specify recording method by schedule with date and time. C: Continuous recording method H: Continuous recording + event recording method (Motion, Sensor) E: Event recording method: if event (Motion, Sensor) happens, recording works. N: No Recording. A. Click time table to change recoding method. B. Click channel number to change recording method for all time. C. Click time label to change recording method for all days. D.
USER’S MANUAL F. Click “Holiday” button to specify date of holiday. G. To add specific date to the holiday list, select date on the calendar and “Add” button. Selected date shows as yellow colored rectangle. H. To delete specific date in the holiday list, select date on the holiday list and click “Delete” button. Selected holiday date shows as blue-green colored rectangle. I. Click “OK” button to save current holiday setting and back to schedule menu. J.
USER’S MANUAL 4) Network You can set the network environments. 1. [TCP/IP] You can specify the TCP/IP setting according to network environment. Specifying the TCP port number of Web, Playback and Live. Default values: Web(80), Playback(9091), Live(9092) For dynamic IP or PPPoE All the items of IP address, subnet mask, gateway and DNS are disabled and set each value automatically. For static IP IP Address: Enter IP address received from ISP using screen keyboard.
USER’S MANUAL ※ If the network of DVR is connected via router, you must set Configuration of port forwarding according to the router. (web, search, live ports) Please refer to user's guide of the router which you are using. ※ UPnP IGD : The IP router setting of port forwarding for web, playback and live ports can be done automatically. Caution UPnP IGD feature will be disabled if IP router does not support UPnP IGD or it turned off it in the router settings.
USER’S MANUAL 3. [DDNS] You can use DynDns or dvrdns service : Visit www.dyndns.com or www.dvrdns.net and And domain name. You can connect to DVR easily using host name instead of IP address with DDNS PPPOE 4. Mode: Enabling or disabling DDNS. 5. Server: IP address of DDNS. 6. Port: TCP port number of DDNS. 7. Domain: The domain name of DVR device. 8. Interval: Setting the interval of IP address updating.
USER’S MANUAL 4. [CMS] Specifying IP address and TCP port number of CMS. 9. Mode: Enabling or disabling event report to the central monitoring center when event occurs. 10. IP address: The IP address of the central monitoring center. 11. Port: The TCP port number of the central monitoring center. H.
USER’S MANUAL 5. [E-mail] You can set the E-mail notification when event occurs. 12. Mode: Enabling or disabling E-mail notification. (OFF / Authentication / Not authentication) 13. SMTP server: Setting the IP address or domain name of SMTP server. 14. Port: Setting the TCP port number of SMTP (Default value is 25). 15. Account: Setting the E-mail account registered in SMPT server. 16. Password: Setting the password of the E-mail account. 17. Sender: Setting the E-mail address of sender. 18.
USER’S MANUAL 5) User You can create new user, modify authority, delete user. ① ② ③ ④ ① [User list] You can view the list of all users. ② [Create user] H.
USER’S MANUAL A. Total: It displays the number of registered users and the maximum number of users can be registered. B. User ID: Input user id to create. C. Password: Input password for the user id. D. Authority items: Specify each authority item for the user id. A. Setup B. Manual alarm C.Search D.Backup E. Network F. Multi login G. PTZ H.Audio E. Cameras: Specify the cameras which the user can see. ③ [Modify authority] A. User ID: Select a user id to modify authority. B.
USER’S MANUAL F. Multi login G. PTZ H. Audio D. Cameras: Specify the cameras which the user can see. ④ [Delete user] Select user id to delete. H.
USER’S MANUAL 2-4. PTZ control It is used to control PTZ camera which is connected at RS-485 port. Settings of camera and DVR should be done if you are to control PTZ camera. 1. Click the icon PTZ bar to control PTZ in first main menu. 2. Control the PTZ camera using each item below. ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ⑪ ⑫ ⑬ ⑭ ① Click this button or press “CANCEL” button on the remote controller to close the PTZ control window. ② Click this spin control to select PTZ camera.
USER’S MANUAL ⑫ Click to delete specified preset number. ⑬ Click to start touring, which function traverse each preset position one by one according to dwell time. ⑭ Click to stop touring. Setting a new preset position 2. Select the preset number to set using button ⑨. 3. Click button ⑪ “SET”. 4. Repeat process 1 ~ 3 stage to set another preset position. Preset numbers are available up to 16. ※ The maximum preset number is different according to the specification of camera.
USER’S MANUAL 2-5. Search (playback) and backup Various features are available for user to search recorded data easily. 1) Time search You can search recorded data with date and time. How to search recorded data A. Click Search bar on Main menu button on main menu bar. B. Select the date you want to search on the calendar above. (The date with recorded data is displayed in bold.) C. Then recorded time table will be displayed. D.
USER’S MANUAL 2) Event Search You can search recorded data using event occurrence time. A. Click the Event Search bar on search menu bar. B. Use C. Check sensor, motion check box below to filter out the events. D. Move to previous or next page using – and + buttons. E. Select a data to search from the list. Click the mouse button to move to the corresponding buttons on the upper right side to select camera to search. recorded data. F.
USER’S MANUAL 3) Backup You can back up the recorded data which you select date/time and channels. A. Click mouse on the Back up bar on Search menu bar. B. Select a device to backup data will be stored. C. If you want to select cameras to backup, click “Set” button and select cameras you want. Then click “OK” button. D. Selected cameras will be displayed below. E. Specify starting date/time of backup period. F. Specify ending date/time of backup period. G.
USER’S MANUAL How to erase media Î You can erase data in the storage media, like USB memory stick Î When you are to use USB memory, after connecting USB memory to USB port, click “Erase media” button to erase media. Î It is recommended to backup important data stored in USB memory before using this function. ※ The backup process is not started if you specify invalid starting and ending date/time. ※ The backup period cannot exceed 24 hours. ※ The USB memory should be formatted as FAT32.
CHAPTER 3 Web viewer 3-1 Installation ---------------------------------------------------------------------------------------- 60 1. Web viewer installation .............................................................................. 60 3-2 Functional description --------------------------------------------------------------------------- 62 1. Web viewer monitoring window ................................................................. 62 2. Web viewer search window .....................................
USER’S MANUAL Installation 3-1. Set up the network before the installation. 1. Web viewer installation ① Enter the DVR IP address in the Web address window, and then the following Active-X installation window will be displayed. ② When you click on the Active-X install button, the following window will be displayed. Press the Install button. H.
USER’S MANUAL ③ Press the Next button from the Web View installation window. When the installation is completed, the Web initialization screen will be displayed. (General installation recommended) ④ Enter the ID and password. (Multi-login is not enabled and you must log in to the DVR with an unused ID.) (Default: admin, user1, user2, user3) Caution Web Viewer and CMS cannot be used at the same time. Max 3 users are allowed to access DVR simultaneously. H.
USER’S MANUAL Functional description 3-2. 1. Web viewer monitoring window ③ ④ ⑤ ② ⑥ ⑦ ⑧ ⑨ ⑪ ⑫ ① ⑩ ⑬ ⑭ ① Divide screen division (Full screen/1/4/ 9 in addition for HX08) ② Selecting a camera ③ Real time image capture (Save as JPEG) ④ Settings (It is available only when you logged in as admin) ⑤ Enable or disable incoming audio (Default value is disable.
USER’S MANUAL 2. Web viewer search window ③ ④ ⑤ ⑧ ⑩ ① ② ⑬ ⑥ ⑦ ⑨ ⑪ ⑫ ① Divide screen division (Full screen/1/4, 9 in addition for HX08) ② Selecting a camera ③ Saving video or still image (Saving as AVI/JPEG/BMP) ④ Date/Time selection button to play back (Refer to 3. Search dialog box) ⑤ Enable or disable incoming audio (Default value is disabled.
USER’S MANUAL 3. Search Menu ① ② ⑤ ③ ④ ⑥ ⑧ ⑦ ① Recorded data graph (Click on the data graph to select time to play.) ② Time scroll bar ③ Zoon in/out of graph (It can be scaled from 2 hours to 24 hours by minute unit.) ④ Displaying selected data/time ⑤ Displaying calendar (The dates are shown in bold if recorded data exist.) ⑥ Description of the color of the recorded data graph ⑦ “OK” button (Video is played immediately when you selected data/time which has recorded data.
USER’S MANUAL 4. Saving as AVI file dialog box ⑤ ⑥ ⑦ ① ② ③ ④ ⑧ ⑨ ⑩ ① Camera name/Date/Time which is currently displayed. ② Starting AVI saving (File name is requested when you click on this button.) ③ Stopping AVI saving ④ Closing Save as AVI dialog box (It will be closed automatically after stopping AVI file if it is being saved.) ⑤ Specifying time period to save AVI file. ⑥ Starting time to save AVI file. ⑦ Stopping time to save AVI file.
USER’S MANUAL CHAPTER 4 Using smart phone 4-1 Functional description -------------------------------------------------------------------------- 67 1. Real-time monitoring ................................................................................. 67 H.
USER’S MANUAL 4-1. Functional description 4. Real-time monitoring If you can use Wi-Fi environments, you can view the real-time monitoring video from DVR with smart phone ① Run web browser at smart phone, and enter DVR IP address. ② Enter id and password, and click “login” button the real-time monitoring screen will be shown.
USER’S MANUAL CHAPTER 5 Appendix 5-1 Check before requesting for service -------------------------------------------------------- 69 5-2 Recommended device to use------------------------------------------------------------------ 72 5-3 Factory Default ------------------------------------------------------------------------------------ 74 5-4 Product specification ----------------------------------------------------------------------------- 79 H.
USER’S MANUAL 5-1. Check before requesting for service Check before requesting for service. If the following symptoms are observed when using the product, recheck the following. It may not be a problem. Symptom Checkpoint and resolution Check whether the power plug is correctly plugged. I cannot turn on the power of the Check whether the voltage of the power supply is correct.
USER’S MANUAL Symptom Checkpoint and resolution Check whether the recording audio channel is correctly set up. I cannot hear the audio recorded Check whether the connecter on the rear side of the device is connected with the video. with external device (Line input) correctly. Check whether the connected external device is operating correctly.
USER’S MANUAL Symptom Checkpoint and resolution When the E-mail transmission fails without SMTP server setting. z Check whether the network is set up correctly. z Check whether the E-mail address is entered correctly. z Check the spam mail setting for the entered E-mail address. (If the spam mail is set, some mails may automatically be deleted or classified into spam mail box etc.) z Some SMTP mail server providers does not support sent email from the commercial SMTP server.
USER’S MANUAL 5-2.
USER’S MANUAL List of supported PTZ camera Protocol Manufacturer Pan/Tilt Zoom Focus Iris Preset Tour LG Multix_E LG x ○ ○ ○ x x LG Multix LG ○ ○ ○ ○ ○ ○ LPT-A100L LG ○ x x x x x LG x ○ ○ ○ x x Honeywell ○ ○ ○ ○ ○ ○ Sony ○ ○ ○ x x x New Born ○ ○ ○ ○ ○ ○ Dongyang ○ ○ ○ ○ ○ ○ PLECO -D / PELCO Co.,Ltd PELCO ○ ○ ○ ○ ○ ○ PLECO -P / PELCO Co.
USER’S MANUAL 5-3. Factory default 1 Step 2 Step 3Step 4Step INPUT Default 00~99 00 Language Overview Remote ID Auto-switching interval Spot-out 5~60sec. 30sec. CH1 ~ CH4 / CH8 CH1 Button sounds On/Off On Use retain data On/Off Off Retain days 1 ~ 60days 30days Use controller On/Off On Device ID 0 1200/2400/4800/960 0/19200/38400/ 57600/115200bps Baud rate Date/Time GMT + 00:00 ~ GMT -12:00 Off Pool.ntp.
USER’S MANUAL Disable / CH1 ~ CH4 / CH8 Disable / CH1 ~ CH4 / CH8 Disable / CH1 ~ CH4 / CH8 CIF/ Half-D1/ D1 1~4/1~8 Very low Low Normal High Very high Audio2 Audio3 Audio4 Resolution Camera no. Quality Recording Color OSD Disable CIF 1 Normal CIF : 30, Half-D1 : 30, D1 : 15 Event frame rate Normal frame rate 1 / 2 / 3 / 5 / 7 / 10 / 15 / 20 / 25 / 30 Camera no.
USER’S MANUAL Sensor no. HSDN251 MD200 New Born WVCS850 PELCO-D PELCO-P SCC-641 SPD-2300 SUNGJIN DSC230 V1305R-DC Not use 1200/2400/4800/960 0/19200/38400/5760 0/ 115200bps 1~4 Active sensor Check / Uncheck Check Sensor type Active alarm Latency time Active alert Latency time N.O. / N.C. Check / Uncheck 1 ~ 10sec. Check / Uncheck 1 ~ 10sec. N.O. Check 10sec. Check 10sec. Sensor no. 1~4 1 Check / Uncheck CH1 Alarm Check / Uncheck Uncheck Alert Check / Uncheck Uncheck Camera no.
USER’S MANUAL Schedule HDD full / Sensor / Alarm / Motion / Alert / Abnormal termination / Video loss Camera no. Recording method Day IP Configuration TCP / IP 1~4/8 1 C/H/E/N H SUN ~ SAT Dynamic IP Static IP PPPoE - IP address - Subnet mask - Gateway - DNS - MAC address - Web port PPPoE Playback port 80 9091 Live port 9092 UPnp IGD Check / Uncheck Uncheck Status Disconnect / Connect - User ID - Password www.dvrdns.net / www.dyndns.
USER’S MANUAL User list Create user Password - Sender - Receiver - E-mail test - admin - guest - user1 - user2 - user3 - User ID - Password Authority Channel User Setup Manual Alarm Search Backup Network Multi login Check / Uncheck 000000 Check Check / Uncheck Check Check / Uncheck Check / Uncheck Check / Uncheck Check Check Check Check / Uncheck Uncheck PTZ Check / Uncheck Check Audio CH1 ~ CH4 / CH8 Check / Uncheck Check Check / Uncheck Check Select user User ID
USER’S MANUAL 5-4. Product specification MODEL HX04 HX08 OPERATING SYSTEM Embedded Linux COMPRESSION H.