User`s guide

VersaTools
®
MTP 15HD A Series • InstallationVersaTools
®
MTP 15HD A Series • Installation
VersaTools
®
MTP 15HD A Series, cont’d
VersaTools
®
MTP 15HD A Series • SpecificationsVersaTools
®
MTP 15HD A Series • Specifications
c. Use a Tweeker or other small screwdriver to press the
Select button one more time to save the most recent
adjustment or allow the 10-second timeout to elapse.
4. If the remaining color is left shifted, repeat steps 2 and 3.
Non-SEQ receivers skew compensation
Try using the following methods to minimize or eliminate pair
skew:
• Switch to Extron’s Enhanced Skew-Free A/V UTP cable.
• Add a skew compensation cable equal to the length of
pair skew to the receiver’s output.
• Install an SEQ 100 15HD Skew Equalizer on the receiver’s
video output and adjust the skew for the leading video
image.
Specifications
Video
Gain ............................................... Unity
Number/signal type ................... 1 set of proprietary analog signals
Connectors.................................... 1 female RJ-45
Video input and loop through — transmitters
Number/signal type ................... 1 analog RGBHV, RGBS, RGsB, RsGsBs,
component video, S-video, or composite
video
1 buffered RGBHV, RGBS, RGsB, RsGsBs
local monitor loop through (includes ID
bits)
Connectors.................................... 2 female 15-pin HD
Nominal level............................... 1 V p-p for Y of component video and
S-video, and for composite video
0.7 V p-p for RGB
0.3 V p-p for R-Y and B-Y of component
video, and for C of S-video
Minimum/maximum levels ...... 0.3 V to 1.45 V p-p
Impedance .................................... 75 ohms
Horizontal frequency .................. 15 kHz to 130 kHz
Vertical frequency ....................... 30 Hz to 150 Hz
Return loss .................................... <-30 dB @ 5 MHz
DC offset (max. allowable)......... 250 mV
Video output — receivers
Number/signal type
MTP R 15HD A ................ 1 analog RGBHV, RGBS, RGsB, RsGsBs,
component video, S-video, or composite
video
MTP RL 15HD A, MTP RL 15HD A SEQ
1 set of proprietary analog signals
1 analog RGBHV, RGBS, RGsB, RsGsBs,
component video, S-video, or composite
video
Connectors
MTP R 15HD A ................ 1 female 15-pin HD
MTP RL 15HD A, MTP RL 15HD A SEQ
1 female RJ-45
1 female 15-pin HD
Nominal level............................... 1 V p-p for Y of component video and
S-video, and for composite video
0.7 V p-p for RGB
0.3 V p-p for R-Y and B-Y of component
video, and for C of S-video
Minimum/maximum levels ...... 0.3 V to 1.45 V p-p
Impedance .................................... 75 ohms
Return loss .................................... <-30 dB @ 5 MHz
DC offset ....................................... <±20 mV with input at 0 offset
Sync
Input type (transmitters) ............ RGBHV, RGBS, RGsB, RsGsBs
Output type (receivers)............... RGBHV, RGBS, RGsB, RsGsBs
Standards ...................................... NTSC 3.58, NTSC 4.43, PAL, SECAM
Input level (transmitter) ............. 3.5 V to 5.5 V p-p, unterminated
Output level (receivers) .............. 4.0 V to 5.0 V p-p, unterminated
Input impedance (transmitter) .. 510 ohms
Output impedance (receivers) ... 110 ohms
Max. input voltage (transmitter) 5.5 V p-p
Polarity
Transmitter ....................... Positive or negative
(follows input polarity)
Receivers ........................... Positive or negative (switch-selectable)
Audio
Number/signal type ................... 1 set of proprietary analog signals
Connectors.................................... 1 female RJ-45
Gain ............................................... Unbalanced output: 0 dB; balanced
output: +6 dB
2322