TP T Series Transmitters TP T 15 HD A TP T 15 HD AV TP T BNC DA4 Audio/Video Twisted Pair Cable Transmitters 68-546-03 Rev.
Precautions Safety Instructions • English Warning This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. Power sources • This equipment should be operated only from the power source indicated on the product. This equipment is intended to be used with a main power system with a grounded (neutral) conductor. The third (grounding) pin is a safety feature, do not attempt to bypass or disable it.
FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.
PRELIMINARY TP T Series Transmitters
Table of Contents Chapter One • Introduction . ..................................................................................................... 1-1 About this Manual ..................................................................................................................... 1-2 About the TP T Series Transmitters .................................................................................. 1-2 Recommended transmission distances ............................................................
PRELIMINARY Table of Contents, cont’d ii TP T Series Transmitters • Table of Contents
1 Chapter One Introduction About this Manual About the TP T Series Transmitters Features PRELIMINARY TP T Series Transmitters
Introduction About this Manual This manual describes the procedures for installing and using the Extron TP Series transmitters, including the TP T 15HD A, TP T 15HD AV, and TP T BNC DA4. The terms “TP T transmitter” and “transmitter” are used interchangeably throughout this manual to refer to these three products generically.
TP T Series transmitter to TP R BNC A and TP R BNC A AV receivers using CAT 5/5e/6 or Enhanced Skew-Free cable at 60 Hz Maximum distance, high quality Maximum distance, variable quality Component video 1000' (300 m) 1050' (320 m) Composite video 1000' (300 m) 1050' (320 m) S-video 1000' (300 m) 1050' (320 m) 640 x 480 1000' (300 m) 1050' (320 m) 800 x 600 800' (245 m) 900' (275 m) 1024 x 768 600' (185 m) 700' (215 m) 1280 x 960 450' (135 m) 600' (185 m) 1280 x 1024 400' (120 m) 500'
Introduction, cont’d Output — An RJ-45 connector provides a connection to an Extron TP R receiver. Horizontal shift — Allows you to adjust the horizontal placement of the computer video image on the screen. This is also called “horizontal centering”. DDSP™ (Digital Display Sync Processing™) — Allows the sync signal to pass through without altering sync pulse timing or width. TP T 15HD AV transmitter Video inputs — Computer video — Accepts computer analog video on a female 15-pin HD connector.
2 Chapter Two Installation Installation Connections and Cabling on the Front and Rear Panels Controls and Indicators on the Front and Rear Panels Troubleshooting PRELIMINARY TP T Series Transmitters
Installation and Operation Installation Installation and service must be performed by authorized personnel only. C Overview To install and set up a TP transmitter for operation, follow these steps: 1 Disconnect power from all of the equipment, including the video source(s) (such as computers or DVD players), the transmitter, the receiver(s), and the output display(s). 2 If using component, S-video, or composite video, reconfigure the video jumpers as needed.
Configuring video jumpers for component, S-video, and composite video The TP T Series transmitters are configured at the factory for RGB video. To transmit component video (bi-level sync only), S-video, or composite video, you must place the video jumpers on the transmitter’s internal main board as follows: 1. Remove the two screws on each side of the unit and one screw on top. 2.
Installation and Operation, cont’d Setting audio jumpers for use with unmodified receivers N Older (unmodified) transmitters and receivers are fully compatible with each other, but not with the TPX 88 A twisted pair matrix switcher. Redesigned (modified) transmitters and receivers are fully compatible with each other and with the TPX 88 A. You can use jumper connections to make redesigned transmitters and receivers compatible with the unmodified models, but not with the TPX 88 A.
Mounting the transmitters The TP T Series transmitters can be set on a table; mounted on a rack shelf; or mounted through or under a desk, podium, or tabletop. The following optional mounting kits are available: • RSM 100 — Rack shelf mount kit for twisted pair products (#70-123-01) • RSB 129 — 1U, 9.5" deep basic rack shelf (#60-604-01, -02) • RSU 129 — 1U, 9.
Installation and Operation, cont’d The following illustration shows how to mount the transmitter on a 9.5" rack shelf. 1U Universal Rack Shelf RSM 100 TP Mounting Bracket (2) 4-40 x 3/16" Screws PRELIMINARY Use 2 Mounting Holes (each side) Rack mounting the transmitter Under-desk mounting Furniture-mount the transmitter under a desk or shelf using the optional mounting kit (part #70-077-01), as illustrated below. To mount the transmitter under a desk, podium, or table top, 1.
6. Drill pilot holes 1/4 inch (6.4 mm) deep and 3/32 inch (2 mm) in diameter into the table or desk top at the marked screw locations. The holes should be drilled from the underside or inside (concealed side) of the furniture where the transmitter will be located. 7. Insert #8 wood screws into the four pilot holes. Tighten each screw into the mounting surface until slightly less than 1/4 inch of the screw head protrudes. 8.
Installation and Operation, cont’d 7. Slide the unit up and down or back and forth in the mounting brackets until the front panel of the unit is at the desired height. Tighten the screws that secure the brackets in place. If the bracket screws are inaccessible to a screwdriver when the unit is in place, a. Mark the location of the brackets relative to the screws. b. Remove the transmitter from inside the furniture. c. Tighten the screws. d. Replace the unit inside the surface.
Connectors and Cabling on the Front and Rear Panels 1 2 3 COMPUTER AUDIO ID PIN 4 ID PIN 11 INPUT BUFFERED H-SHIFT LOCAL MONITOR TP T 15HD A TP T 15HD A front panel 9 DDSP SPARE 7 POWER 15V .5A DC OUTPUT 1 2 COMPUTER AUDIO 4 5 VIDEO AUDIO 3 ID PIN 4 ID PIN 11 PC H-SHIFT BUFFERED L INPUT PRELIMINARY TP T 15HD A rear panel R LOCAL MONITOR TP T 15HD AV TP T 15HD AV front panel 8 7 DDSP SPARE 9 POWER 15V .
Installation and Operation, cont’d a Audio input connector — Connect PC audio to this 3.5 mm stereo jack. Wire the male plug as shown below. N Only analog line level audio signals should be input on the audio input connector. Tip (L) Ring (R) Sleeve ( ) Audio input wiring b Computer Input connector — Connect a computer video source to this female 15-pin HD connector. COMPUTER 10 5 1 6 PRELIMINARY On the TP T 15HD A and the TP T 15HD AV, this connector 15 11 accepts computer video.
f Input BNC connectors — Connect the desired video input device to these BNC connectors, which accept RGBHV, RGBS, RGsB, component video, S-video, and composite video. Transmission of component video, S-video, or composite video requires that internal jumpers be reconfigured. See “Configuring video jumpers for component, S-video, and composite video”, earlier in this chapter. N Input only sync signals (no video signals) on the H/V and V BNC connectors.
Installation and Operation, cont’d Terminating TP cable The figure below details the recommended termination of TP cables in accordance with the TIA/EIA T 568A wiring standards. Pins: 12345678 RGB video and audio Pin Wire color Signal RJ-45 Connector AV video and audio Signal Level 1 White-green Red/V. sync + ±0.35 V Video + +0.35 V 2 Green Red/V. sync – ±0.35 V Video – –0.35 V 3 White-orange Audio and power Insert Twisted Pair Wires Level +15 V with Audio +* & +15 V ±0.
TP T 15HD A IF cable measurement indicates that the pair with wires 1 and 2 is four feet shorter than the other pairs... AU DIO CO MP UT INP UT ID PIN 4 ID PIN 11 ER BU FF ER ED LO CA Audio H-S L MO NIT OR HIF T TP T 15 HD A ER DC POW .5A 15V DI AU O L B R SOG C SYNC A V B B HV H/ TPUT OU L R TP R BNC A RG G R T B IN PU RG PC Computer CAT 5 UTP Cable RGB video 1, 2 Red 4, 5 Green 7, 8 Blue ...
Installation and Operation, cont’d Controls and Indicators on the Front and Rear Panels All of the transmitters have front panel Power indicators. In addition, the TP T 15HD A and TP T 15HD AV have horizontal shift control on the front panel and DIP switches on the front and rear panels. 1 3 2 AUDIO COMPUTER ID PIN 4 ID PIN 11 INPUT BUFFERED H-SHIFT LOCAL MONITOR TP T 15HD A TP T 15HD A front panel DDSP SPARE 4 POWER PRELIMINARY 15V .
a Power/signal LED — Amber: Indicates that power is applied, but that the transmitter is not connected to a receiver. Green: Indicates that the transmitter is properly connected to a receiver. b ID bit switches (TP T 15HD A and TP T 15HD AV) — If a local monitor is installed, set both of these DIP switches to Off. If a local monitor is not installed, set both switches to On. c H. Shift (TP T 15HD A) and PC H.
Installation and Operation, cont’d If the image is not displayed correctly 1. For computer video, if the output image looks too green, ensure that the receiver’s SOG switch is set to Off. 2. For computer video, if the picture hangs off the edge of the screen, adjust the transmitter’s H Shift control. N DDSP disables the horizontal shift control. 3. Place the receiver’s Manual/Auto switch to manual and adjust the level and peaking controls for optimum quality. 4.
A Appendix A Specifications, Part Numbers, and Accessories Specifications Part Numbers PRELIMINARY TP T Series Transmitters
Specifications, Part Numbers, and Accessories Specifications Video — video models Number/signal type ��������������������� 1, 2, or 4 sets of proprietary analog signals Connectors ������������������������������������� 1, 2, or 4 female shielded RJ-45 PRELIMINARY Video input — video models Number/signal type TP T 15HD A ���������������������� 1 analog RGBHV, RGBS, RGsB, component video, S-video, or composite video; or 1 S-video and 1 NTSC/PAL/SECAM composite video from a single source; or 3 NTSC/PAL compos
Audio input — audio models Number/signal type TP T 15HD A ���������������������� TP T 15HD AV ������������������� Connectors TP T 15HD A ���������������������� TP T 15HD AV ������������������� Impedance �������������������������������������� Nominal level �������������������������������� Maximum level ������������������������������ CMRR ���������������������������������������������� N 1 stereo, unbalanced 2 stereo, unbalanced (1) 3.5 mm mini jack (1) 3.
Specifications, Part Numbers, and Accessories, cont’d Part Numbers Included parts These items are included with the TP T Series Transmitter: Included part Replacement part number TP T 15HD A 60-345-02 TP T 15HD AV 60-346-03 TP T BNC DA4 60-349-02 PS 1508 single output external power supply, 15 V, 0.8 A 70-776-01 Captive screw connector, 3-pole, 3.5 mm 10-265-03 TP Transmitters Series Setup Guide PRELIMINARY N The TP T 15HD AV is a redesigned transmitter.
Cables and adapters N Skew-Free™ A/V UTP cables are not recommended for Ethernet/LAN locations. Skew-Free™ A/V cable Part number UTP 23SF-4/3 — 3' (90 cm) 26-569-01 UTP 23SF-4/6 — 6' (1.8 cm) 26-569-02 UTP 23SF-4/12 — 12' (3.6 m) 26-569-03 UTP 23SF-4/25 — 25' (7.6 m) 26-569-04 UTP 23SF-4/35 — 35' (10.6 m) 26-569-05 UTP 23SF-4/50 — 50' (15.2 m) 26-569-06 UTP 23SF-4/75 — 75' (22.8 m) 26-569-07 UTP 23SF-4/100 — 100' (30.
PRELIMINARY Specifications, Part Numbers, and Accessories, cont’d A-6 TP T Series Transmitters • Specifications, Part Numbers, and Accessories
Extron Warranty Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase.
Extron USA - West Headquarters +800.633.9876 Inside USA / Canada Only +1.714.491.1500 +1.714.491.1517 FAX Extron USA - East Extron Europe Extron Asia Extron Japan Extron China Extron Middle East +800.633.9876 +800.3987.6673 +800.7339.8766 +81.3.3511.7655 +81.3.3511.7656 FAX +400.883.1568 +971.4.2991800 +971.4.2991880 FAX +1.919.863.1794 +1.919.863.1797 FAX +31.33.453.4040 +31.33.453.4050 FAX +65.6383.4400 +65.6383.
