User’s Manual C Do not connect this device to a computer data or telecommunications network TP Receivers Family High Resolution Video, Composite Video, and Stereo Audio Twisted Pair Cable Transmission Products 68-547-02 Rev.
Precautions Safety Instructions • English This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock. Caution Read Instructions • Read and understand all safety and operating instructions before using the equipment.
Precautions, cont’d 安全须知 • 中文 警告 这个符号提示用户该设备用户手册中 有重要的操作和维护说明。 电源 • 该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。 设 备 必须使用有地线的供电系统供电。 第三条线 （地线）是安全设施，不能不用或跳过。 这个符号警告用户该设备机壳内有暴 拔掉电源 • 为安全地从设备拔掉电源，请拔掉所有设备后 或桌面电源的电源线，或任何接到市电系统的电源线。 露的危险电压，有触电危险。 电源线保护 • 妥善布线， 避免被踩踏，或重物挤压。 注意 阅读说明书 • 用 户 使 用 该 设 备 前 必 须 阅 读 并 理 解所有安全和使用说明。 保存说明书 • 用户应保存安全说明书以备将来使 用。 遵守警告 • 用户应遵守产品和用户指南上的所有安 全和操作说明。 维护 • 所有维修必须由认证的维修人员进行。 设备内部 没有用户可以更换的零件。为避免出现触电危险不要自 己试图打开设备盖子维修该设备。 通风孔 • 有些设备机壳上有通风槽或孔，它们是用来防止 机内敏感元件过热。 不要用任何东西挡住通风孔。 锂电池 • 不正确的更换电池会有
Table of Contents Chapter One • Introduction ................................................... 1-1 About the TP Receivers ...................................................... 1-2 Features ..................................................................................... 1-4 TP R BNC A receiver .............................................................. 1-4 TP R BNC AV receiver ............................................................ 1-5 TP R 15HD A receiver ..................................
Table of Contents, cont’d All trademarks mentioned in this manual are the properties of their respective owners. 68-547-02 Rev.
TP Receivers 1 Chapter One Introduction About the TP Receivers Features
Introduction, Introductioncont’d About the TP Receivers The TP R BNC A, TP R BNC AV, and TP R 15HD A are Extron Twisted Pair (TP) receivers that receive transmissions of RGB video, component video, S-video, composite video, and stereo audio over Extron Enhanced Skew-Free™ A/V UTP cable or standard Category (CAT) 5 unshielded twisted pair (UTP), shielded twisted pair (STP), or foil shielded twisted pair (FTP) cable. Standard transmission distances are shown in the following tables.
Recommended transmission ranges at 60 Hz, TP R BNC A and TP R BNC AV Video format Component, S-video, Composite video and audio 640 x 480 800 x 600 1024 x 768 1280 x 960 1280 x 1024 1360 x 765 1365 x 768 1366 x 768 1440 x 900 1400 x 1050 1600 x 1200 1920 x 1200 Maximum range (High Quality) Maximum range (Variable Quality) 1000 feet (304 m) 1050 feet (320 m) 1000 feet (304 m) 800 feet (243 m) 600 feet (182 m) 450 feet (137 m) 400 feet (120 m) 400 feet (120 m) 400 feet (120 m) 400 feet (120 m) 350 feet (
Introduction, cont’d Features All Extron TP receivers provide the following features: Audio output — Provides unbalanced (left/right) audio on RCA connectors, and balanced or unbalanced audio on 3.5 mm, 5-pole captive screw connectors. Level control — Allows manual control of image brightness. Peaking control — Allows manual control of image sharpness. TP R BNC A receiver The TP R BNC A receiver has the following features: Video output — Provides RGBHV, RGBS, or RGsB video on 5 BNC connectors.
TP R BNC AV receiver The TP R BNC AV receiver has the following features: Video output — Provides RGBHV, RGBS, or RGsB video on 5 BNC connectors, and composite video on 1 BNC connector. RJ-45 connector — Allows attachment to an Extron TP transmitter. One connector is for computer input and one is for A/V input. Cable length compensation — Provides selection between automatic or manual compensation for long cable runs. Mounting — Mounts in a rack with an Extron Universal Rack Shelf Kit for 9.
Introduction, cont’d This page intentionally left blank.
TP Receivers 2 Chapter Two Installation and Operation Installation Overview Front Panel Controls and Indicators Troubleshooting
Installation Installation and andOperation Operation, cont’d Installation Overview To install and set up a TP receiver and the associated TP transmitter(s) for operation, perform the following steps: 1 Disconnect power from all of the equipment, including the video source, (such as computers or DVD players), the transmitter, receiver, and output displays.
N The following transmitters are compatible with the TP R 15HD A, TP R BNC A and TP R BNC AV receivers: TP T 15HD 45, TP T A 45, TP T 15HD A, TP T 15HD AV, N All TP transmitters include a 15 V or 12 V external power supply. The transmitters (with the exception of the TP T 15HD 45 and TP T A 45) also receive power from the associated Extron TP receiver(s) (with the exception of the TP R 15HD A) via the TP cable.
Installation and Operation, cont’d Video jumpers The TP R BNC A and TP R BNC AV receivers can be configured to receive component video (bi-level sync only), S-video, or composite video. N 1. The receivers are factory configured for RGB video. To receive any other type of video, reconfigure the jumpers. Remove the three screws on each side and the two screws on top of the cover (figure 2-1). Remove 8 Screws A 1.
5. 6. Locate J3 on the RGB video printed circuit board. See figure 2-1. a. For RGB video, ensure that pin 2 is jumpered to pin 3. b. For any other video format, ensure that pin 1 is jumpered to pin 2. Reinstall the video board, replace the cover, and reinstall the screws and BNC connector hex nuts. Video DIP switch C SYNC SOG C VIDEO N/C The TP R 15HD A receiver can be configured to receive component video (bi-level sync only), S-video, or ON composite video.
Installation and Operation, cont’d Shift internal jumpers as follows: 1. Remove three screws on each side and two screws on top of the cover (figure 2-2). Remove 8 Screws A 1.
Mounting the receiver UL guidelines for rack mounting The following Underwriters Laboratories (UL) guidelines are relevant to the safe installation of the TP Receivers in a rack: 1. Elevated operating ambient temperature — If the unit is installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient temperature.
Installation and Operation, cont’d Rack mounting (TP R BNC A, TP R BNC AV, TP R 15HD A) TP R BNC A, TP R BNC AV, or TP R 15HD AV — For optional rack mounting, mount the receiver on a Universal Rack Shelf Kit for 9.5 inch deep products (Extron part #60-190-01) (figure 2-3). The TP R BNC A and TP R BNC AV mount on the left or right side of the rack. The TP R 15HD A mounts in one of eight locations on the rack.
TP R 15HD A only — For optional rack mounting, mount the receiver on a Rack Shelf Kit for 3.5 inch deep products (Extron part #60-190-20), figure 2-4. The TP R 15HD A mounts in one of four locations on the rack. RG B LE VE L TP PEAK R 15 ING HD A 3.5” Deep Rack Shelf RG B LE VE L TP PEAK R ING 15 HD A 1/4 Rack Width False Front Face Plate Use 2 Mounting Holes on Opposite Corners RG B LE VE L TP PEAK R ING 15 HD A (2) 4-40 x 3/16" screws Figure 2-4 — Rack mounting the TP R 15HD A 1.
Installation and Operation, cont’d Furniture mounting All receiver models can be mounted under furniture such as a table or podium surface using the appropriate optional mounting bracket; the Extron Under-Desk Mounting Kit for 1/8 and 1/4 Rack Width Products (part #70-212-01) (TP R 15 HD A) or Under-Desk Mounting Kit for 1/2 Rack Width Products (part #70-077-01) (all other models).
5. For through-surface mounting (all except TP R 15HD A), insert four #8 wood screws through the bracket and into the four pilot holes. Tighten all four screws to secure the receiver in place. 6. For under-surface mounting, insert #8 wood screws into the four pilot holes. Tighten each screw into the mounting surface until slightly less than 1/4 inch of the screw protrudes. 7.
Installation and Operation, cont’d Rear panel features and cabling 6 7 VIDEO 8 A-V AUDIO A R L B 9 100-240V R A-V INPUT AUDIO A R R G B H/HV RGB OUTPUT AUDIO L B V 50/60 Hz 1 3 5 7 8 1 3 5 7 8 A R G B H/HV RGB OUTPUT TP R BNC AV 9 AUDIO R RGB INPUT R L SOG C SYNC RGB INPUT 0.3A L SOG C SYNC 2 POWER 15V .5A DC B L R L V TP R BNC A 4 RGB AV INPUT 8 L AUDIO 5 R C SYNC SOG C VIDEO N/C 1 9 POWER 15V .
b Composite video input connector — Attach one end of a TP cable to this RJ-45 female connector. Attach the other end to an Extron TP video transmitter outputting composite video. See Termination of TP cable on page 2-17 for pin assignments. Output cabling Computer video The TP R BNC A, TP R BNC AV, and TP R 15HD A receive and output RGB video. These receivers can also receive component (bi-level sync only) video, S-video, or composite video and output them on the R, G, and B signal lines.
Installation and Operation, cont’d d 10 5 15 1 RGB Output 15HD (TP R 15HD A) — Connect the desired video output device to the rear panel output 15HD connector. Refer to the table below for the video signal connections. Pins 13 and 14 are for sync only.
Audio g All TP receivers receive and output stereo audio. The TP R BNC A and AV output audio on both left and right RCA connectors (g) and on 3.5 mm, 5-pole captive screw connectors (h). The TP R 15HD A outputs audio on the captive screw connector (h) only. Stereo audio output connectors — Connect left and right stereo audio cables between these rear panel RCA connectors and the output device stereo audio inputs. Only analog, line level, unbalanced audio signals can be output on these connectors.
Installation and Operation, cont’d Power connector i Power TP R BNC AV — Plug a standard IEC power cord into this connector to connect the TP R BNC AV to a 100 to 240 VAC, 50-60 Hz power source. N If the distance between the transmitter and receiver is too great for the receiver to power the transmitter, the video image will be missing, distorted, noisy, or the receiver Manual/Auto LED will flash. The transmitter will require a local power supply.
Termination of TP cable Figure 2-10 details the termination of TP cables in accordance with the TIA/EIA T 568 A wiring standards. Pins: 12345678 RJ-45 connector RGB video and audio Pin Wire color 1 White-green 7&8 Level AV Video and audio Signal Level Red/V. sync+ ±0.35V Video+ +0.35V Green Red/V. sync- ±0.35V Video- -0.35V 3 White-orange Audio & power +15V with Audio+* & +15V power+ ±0.5 V 4 Blue Green+ +0.35V Reserved None 5 White-blue Green- -0.
Installation and Operation, cont’d Cable testing The TP units are designed for and perform best with Extron Enhanced Skew-Free A/V cable terminated in accordance with the TIA/EIA T 568 A wiring standard. CAT 5, Cat 5e and Cat 6 cables are acceptable but less preferable. Extron also recommends the use of pre-terminated and tested cables. Cables terminated on site should be tested before use to ensure they comply with Category 5/5e/6 specifications.
TP T 15HD A IF cable measurement indicates the pair with wires 1 and 2 is four feet shorter than the other pairs... AU DIO CO MP UT INP UT ID PIN 4 ID PIN 11 ER BU FF ER ED LO CA Audio L MO NIT OR H-S HIF T TP T 15 HD A ER DC POW .5A 15V O DI AU L B R SOG C SYNC A V B B HV H/ TPUT OU L R TP R BNC A RG G R T B PU IN RG PC Computer CAT 5 UTP Cable Pair RGB video 1, 2 Red 4, 5 Green 7, 8 Blue LCD Projector ...
Installation and Operation, cont’d Front Panel Controls and Indicators The TP R Receivers have similar controls and indicators as shown below. 2 1 3 4 5 RGB MANUAL LEVEL PEAKING AUTO TP R BNC A 1 2 3 4 5 VIDEO MANUAL LEVEL PEAKING AUTO RGB MANUAL LEVEL PEAKING TP R BNC AV AUTO Figure 2-12 — TP R BNC A and TP R BNC AV 1 4 5 RGB LEVEL PEAKING TP R 15HD A Figure 2-13 — TP R 15HD A a Power LED Amber — indicates power is applied, but the receiver is not connected to a transmitter.
• b Manual/Auto switch (TP R BNC A and TP R BNC AV) — With this switch in the Auto position, the receiver automatically adjusts level and peaking to compensate for long cable runs. In the Manual position, compensate for long cable runs using the level and peaking controls. N c d e The receiver is connected through a TP switcher to a device that provides a reference ground. If the transmitter is a VTT001, this switch should always be set to Manual.
Installation and Operation, cont’d 8. The transmission distance may be too short. Ensure the UTP cable is at least 50 feet long. 9. If the Manual/Auto switch is in the manual position, ensure the receiver level controls are not set too high. Too much level and peaking can cause display problems. 10. For computer video from a laptop or for ungrounded AC distribution systems, the transmitter may need to be grounded.
TP Receivers A Appendix Specifications, Accessories, and Part Numbers Specifications Included Parts Extron Accessories Cables/Adapters
Specifications, Accessories, Specifications, Accessories, and and Part Part Numbers Numbers cont’d Video Number/signal type ��������������������� 1 or 2 sets of proprietary analog signals Connectors ������������������������������������� 1 or 2 shielded RJ-45 female Video input— refer to the TP Transmitters Family User’s Manual, part #68-546-02 Video output Number/signal type TP R BNC A ������������������������ 1 analog RGBHV, RGBS, RGsB, component video, or S-video; or 1 S-video and 1 NTSC/PAL/SECAM compos
Audio Number/signal type ��������������������� Connectors ������������������������������������� Frequency response ���������������������� THD + Noise ���������������������������������� S/N �������������������������������������������������� Crosstalk ����������������������������������������� Stereo channel separation ������������ CMRR ���������������������������������������������� 1 or 2 sets of analog proprietary signals 1 or 2 shielded RJ-45 female 20 Hz to 20 kHz, >±0.05 dB 0.03% @ 1 kHz, 0.
Specifications, Accessories, and Part Numbers cont’d Power input requirements TP R BNC A ������������������������ 15 VDC, 0.3 A (minimum) TP R 15HD A ���������������������� 15 VDC, 0.
Product weight TP R BNC A ������������������������ TP R BNC AV ��������������������� TP R 15HD A ���������������������� Shipping weight TP R BNC A ������������������������ TP R BNC AV ��������������������� TP R 15HD A ���������������������� Vibration ����������������������������������������� 1.6 lbs (0.7 kg) 2.6 lbs (1.2 kg) 0.4 lbs (0.
Specifications, Accessories, and Part Numbers cont’d Included Parts These items are included in each order for a specific TP receiver: Included parts Part number All TP Receiver Set up Guide Captive screw connector, 5 pole, 3.5 mm (1 or 2) TP R BNC A 60-351-02 Single output external power supply, 15 V, 0.8 A 70-776-01 Captive screw connector, 3 pole, 3.5 mm 100-456-01 TP R 15HD A Single output external power supply, 15 V, 0.
Extron Accessories Accessories Part number PS 150 Multiple output 15 V power supply 60-432-01 RSU 129, Universal Rack Shelf for 9.5 inch deep products 60-190-01 RSB 129, Basic Rack Shelf for 9.5 inch deep products, Gray 60-604-02 RSU 126, Universal Rack Shelf for 6 inch deep products 60-190-10 RSB 126, Basic Rack Shelf for 6 inch deep products 60-604-10 RSF 123, Rack Shelf Kit for 3.5 inch deep products 60-190-20 RSB 123, Basic Rack Shelf for 3.
Specifications, Accessories, and Part Numbers cont’d Enhanced Skew-Free™ A/V UTP Cables Part number UTP23SF-4/3 (3 feet/90 cm) 26-569-01 UTP23SF-4/6 (6 feet/1.0 m) 26-569-02 UTP23SF-4/12 (12 feet/3.6 m) 26-569-03 UTP23SF-4/25 (25 feet/7.6 m) 26-569-04 UTP23SF-4/35 (35 feet/10.6 m) 26-569-05 UTP23SF-4/50 (50 feet/15.2 m) 26-569-06 UTP23SF-4/75 (75 feet/22.8 m) 26-569-07 UTP23SF-4/100 (100 feet/30.4 m) 26-569-08 UTP23SF-4P/25 (25 feet/7.6 m) Plenum 26-570-04 UTP23SF-4P/35 (35 feet/10.
Extron Warranty Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase.
Extron USA - West Headquarters +800.633.9876 Inside USA / Canada Only +1.714.491.1500 +1.714.491.1517 FAX Extron USA - East Extron Europe Extron Asia Extron Japan Extron China Extron Middle East +800.633.9876 +800.3987.6673 +800.7339.8766 +81.3.3511.7655 +81.3.3511.7656 FAX +400.883.1568 +971.4.2991800 +971.4.2991880 FAX +1.919.863.1794 +1.919.863.1797 FAX +31.33.453.4040 +31.33.453.4050 FAX +65.6383.4400 +65.6383.
