Setup Guide User guide

ManualsBrandsExtron Electronics ManualsHardwareTLE 710

Before connecting the TLP 710CV to a

power source, refer to the TLP 710CV user

guide, which is available at

www.extron.com.

TLP 710CV and TLE 710 • Setup Guide

Overview

The Extron TLP 710CV 7-inch Cable Cubby

TouchLink

™

touchpanel and TLE 710 enclosure provide AV connectivity using

convenient pullout cables. The TLP 710CV also provides simple and versatile conguration and control for a range of IPLink

control systems using a touch screen. The touchpanel communicates through an Ethernet connection to a congurable IP Link

control processor. Video and audio input is provided by a twisted pair cable connected to an MTP transmitter.

NOTE: The network output must connect via a network switch, hub, or router to an Ethernet LAN or the Internet, with

an Extron IP Link controller on the same network. Suggested controllers include IPL T S series (for example, IPL T S4),

IPL250, IPL T CR48, IPLTSFI244, or IPCP series.

The rst four pages of this guide provides basic instructions for experienced installers to mount either the TLP 710CV or the

TLE710. The last four pages show initial conguration for the TLP710CV. For reference material and full instructions about

conguring the touchpanel, see the TLP 710CV User Guide (see www.extron.com).

Planning

 Before making any cuts, select the best location for the

TLP710CV or TLE 710.

 Ensure that the edge that opens on the lid is oriented correctly.

 Ensure there is enough space for all the system cables and

components, including cable retractors, if they are to be

installed.

 Decide on the method for cutting a hole in the table:

z Hand router and template

z CNC wood router

z Jigsaw and paper template

 Verify that you have the correct template or dimensions.

 Check all relevant regulations.

z Ensure the installation complies with local, state, and

national building and electrical codes.

z Ensure the installation complies with the Americans with

Disabilities Act or other accessibility requirements.

Tools Required for Installation

Safety Glasses

Phillips Screw Driver

Tape Measure

Vacuum Cleaner

1/4" Hex Nut Driver

Marking Pen

Square

Included Parts

With Power

Module

Without Power

Module

AC Power Module* 1 0

Pass-through AAPs

†

3 3

Blank AAPs 6 6

1-space bracket kit 0 1

2-space bracket kit 3 4

3-space bracket kit 1 1

NOTES:

* Inside the US, the TLP 710CV may be purchased with or without an AC power module. If required, a power module for

the TLE 710 must be purchased separately. Outside the US, see www.extron.com to find an AC power module for

your country.

†

Active or Passive AAPs must be purchased separately (see www.extron.com).

‡

The Power over Ethernet injector is provided only with the TLP 710CV.

Table Clamps

Extron

Removal Tool

Zip Ties

#4−40 Screws

and Nuts

AC Power Module*

Blank AAPs

Pass-thru AAPs

2 Pos

AAP Shelf Bracket Kits

(2 brackets/kit)

3 Pos1 Pos

PWR LAN OUT

LAN-IN

AMBER

GREEN

BLINK

POWER ON

POWER ACTIVE

LOAD ERROR

Power over Ethernet

(PoE) Injector

‡

(TLP 710CV only)

TLP 710CV or TLE 710

Extron

Summary of content (8 pages)

PAGE 1
to a r e 10CV LP 7 10CV us T e g th e TLP 7 t n i t c nne er to th ilable a a re co ef Befo ource, r ich is av om. h s . r w n e , o e r c pow guid ww.ext w TLP 710CV and TLE 710 • Setup Guide Overview The Extron TLP 710CV 7-inch Cable Cubby® TouchLink™ touchpanel and TLE 710 enclosure provide AV connectivity using convenient pullout cables. The TLP 710CV also provides simple and versatile configuration and control for a range of IP Link® control systems using a touch screen.
PAGE 2
TLP 710CV and TLE 710 • Setup Guide (Continued) Mounting the TLP 710CV and TLE 710 Step 1 — Obtain Cut-out Dimensions ATTENTION: • The table should be cut only by licensed and bonded craftspeople. • Make certain the correct cut-out dimensions are being used before proceeding to the next step. Extron is not responsible for mounting holes that are incorrectly cut. • The surfaces of the Cable Cubby enclosure have screws and other protruding hardware that could damage fine furniture.
PAGE 3
Step 3 — Run all Cables Run all cables necessary to support the AC connector, the cables stored in the cubby, and all planned AAP connectors. Run the cables below the table and through the hole that was cut in Step 2. Leave enough slack in the cables to connect or route them before the cubby is installed in the table. Leave enough space under the enclosure for the external power supply and connection of AV cables and the network connection for the TLP 710CV.
PAGE 4
TLP 710CV and TLE 710 • Setup Guide (Continued) Step 7 — Install the AAP Assembly 1. From under the table, push the first AAP assembly through the bottom of the enclosure. The holes in the rear bracket must align with the bottom row of holes on the rear face of the enclosure. TIP: Ensure there is enough space above the AAP assembly for the lid to close completely without cables or connectors contacting the touchpanel. 2. Secure the AAP assembly into position with the provided Phillips head screws. 3.
PAGE 5
Connecting the TLP 710CV NOTE: The rest of this guide applies only to the TLP 710CV (not to the TLE 710). The cable connections are located in a panel on the bottom of the TLP 710CV: c b POWER 12V 1.0A MAX LAN / PoE a a b c MTP MTP connector LAN and PoE connector External power supply connector Step 9 — Connect the MTP Input Connect the output of an Extron Mini Twisted Pair (MTP) transmitter to the MTP socket (a) on the TLP 710CV. This signal provides composite or S-video and audio input.
PAGE 6
TLP 710CV and TLE 710 • Setup Guide (Continued) Step 12 — Power on the TLP 710CV for the First Time Power on all the devices connected to the TLP 710CV. When the 12 VDC power supply or the PoE power supply is switched on, the TLP 710CV will boot up and, if a graphical user interface (GUI) has been designed and loaded onto the touchpanel, that screen will be displayed. If a GUI has not been loaded, a plain blue screen will be displayed.
PAGE 7
Initial Configuration Before use, configure the touchpanel, using the on-screen menus. 1. Remove the bezel, using the Extron removal tool. 2. Press the Menu button once (g in the figures on page 6). The Main menu screen opens. Main Volume Sleep timer: 005 Min Down Up Auto Backlight PoE Active On Time Network Video Backlight: 073% Down Up Exit 3. Touch an on-screen button to highlight and select that option (the button turns green with a yellow border). 4.
PAGE 8
TLP 710CV and TLE 710 • Setup Guide (Continued) Calibration Screen 1. To access the calibration screen, press the Menu button a second time (g in the figures on page 6). The calibration screen opens with the on-screen button in the top left corner highlighted. + + Press and Hold Highlighted Box Until Color Changes + + 2. Press the highlighted button until it turns gray and a new button is highlighted. When all four points have been calibrated, the screen reopens to the Main Screen. 3.